drmindbender Posted August 4, 2012 Share Posted August 4, 2012 I have a SMART Failure predicted on hard disk 3. THe machine has not fully booted yet. I am running unRaid 4.7. Advice? I tried to search for smart failure predicted and did not get good results. Thank! Link to comment
drmindbender Posted August 8, 2012 Author Share Posted August 8, 2012 Statistics for /dev/sdp WDC_WD20EADS-65R_WD-WCAVY2234848 smartctl -a -d ata /dev/sdp smartctl version 5.38 [i486-slackware-linux-gnu] Copyright © 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD20EADS-65R6B0 Serial Number: WD-WCAVY2234848 Firmware Version: 01.00A01 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Aug 8 08:46:55 2012 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (43200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 198 198 051 Pre-fail Always - 250512 3 Spin_Up_Time 0x0027 156 143 021 Pre-fail Always - 9183 4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2170 5 Reallocated_Sector_Ct 0x0033 091 091 140 Pre-fail Always FAILING_NOW 871 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 074 074 000 Old_age Always - 19436 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 74 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 51 193 Load_Cycle_Count 0x0032 144 144 000 Old_age Always - 169600 194 Temperature_Celsius 0x0022 110 099 000 Old_age Always - 42 196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 845 197 Current_Pending_Sector 0x0032 198 198 000 Old_age Always - 781 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 6 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 14 200 Multi_Zone_Error_Rate 0x0008 168 001 000 Old_age Offline - 6566 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Link to comment
mbryanr Posted August 8, 2012 Share Posted August 8, 2012 Replace the drive. See the raw values for pending and reallocated sectors. Sent from my SAMSUNG-SGH-I897 using Tapatalk 2 Link to comment
bubbaQ Posted August 8, 2012 Share Posted August 8, 2012 Yes, that is a very sick drive. Copy/Replace it ASAP. Link to comment
drmindbender Posted August 8, 2012 Author Share Posted August 8, 2012 i have spare drives. there was a parity check running for days and was only at 17% so I stopped it. 1) I will shut down the machine. 2) I will locate the drive in the sever and remove it 3) insert new drive in same slot 4) then what? thanks Link to comment
Joe L. Posted August 8, 2012 Share Posted August 8, 2012 i have spare drives. there was a parity check running for days and was only at 17% so I stopped it. 1) I will shut down the machine. 2) I will locate the drive in the sever and remove it 3) insert new drive in same slot 4) then what? thanks Then just start the array. You might have to check the box under "Start" to enable it, it will say something about re-constructing onto the replacement drive. DO NOT FORMAT THE REPLACEMENT DRIVE (although it is OK to preclear it if you have the time, as that will burn it in. It is NOT necessary to use a per-cleared drive, just they are less likely to die in the first few hours of use). DO NOT SET A NEW DISK CONFIGURATION. Just press "Start" Joe L. Link to comment
drmindbender Posted August 8, 2012 Author Share Posted August 8, 2012 thank you. Started Stop will take the array off-line. Data-Rebuild in progress. Cancel will stop Data-Rebuild. WARNING: canceling Data-Rebuild will leave the array unprotected! that was pretty easy so far. Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.