January 1, 201313 yr Attached is syslog - was running monthly parity check. No errors but syslog shows handle stripe errors on disk0. This is my parity disk. Does this drive need replacing already? My server name is Maiko. I'm also not getting a response when trying to get to unraid's main web page but unmenu is fine. In unmenu when I click on unraid_main, no response. syslog-2013-01-01.txt.zip
January 1, 201313 yr Author Yes, running RC8a. No other plugins. Smart Report: Statistics for /dev/sda ST3000DM001-1CH166_Z1F12RP3 smartctl -a -d ata /dev/sda smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST3000DM001-1CH166 Serial Number: Z1F12RP3 Firmware Version: CC43 User Capacity: 3,000,592,982,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Tue Jan 1 15:49:15 2013 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 113 100 006 Pre-fail Always - 53192888 3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 109 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 7381290 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 745 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 8 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 084 084 000 Old_age Always - 16 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 097 097 000 Old_age Always - 3 190 Airflow_Temperature_Cel 0x0022 069 061 045 Old_age Always - 31 (Min/Max 21/36) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 5 193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 2221 194 Temperature_Celsius 0x0022 031 040 000 Old_age Always - 31 (0 20 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 82394652606630 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 15849455600 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 28169515088 SMART Error Log Version: 1 ATA Error Count: 16 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 16 occurred at disk power-on lifetime: 740 hours (30 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 25d+03:03:43.866 READ DMA EXT ef 10 02 00 00 00 a0 00 25d+03:03:43.865 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 25d+03:03:43.865 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 25d+03:03:43.865 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 25d+03:03:43.864 SET FEATURES [set transfer mode] Error 15 occurred at disk power-on lifetime: 740 hours (30 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 25d+03:03:40.970 READ DMA EXT ef 10 02 00 00 00 a0 00 25d+03:03:40.969 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 25d+03:03:40.969 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 25d+03:03:40.968 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 25d+03:03:40.968 SET FEATURES [set transfer mode] Error 14 occurred at disk power-on lifetime: 740 hours (30 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 25d+03:03:38.015 READ DMA EXT ef 10 02 00 00 00 a0 00 25d+03:03:38.014 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 25d+03:03:38.014 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 25d+03:03:38.014 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 25d+03:03:38.013 SET FEATURES [set transfer mode] Error 13 occurred at disk power-on lifetime: 740 hours (30 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 25d+03:03:32.160 READ DMA EXT ef 10 02 00 00 00 a0 00 25d+03:03:32.159 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 25d+03:03:32.159 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 25d+03:03:32.158 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 25d+03:03:32.158 SET FEATURES [set transfer mode] Error 12 occurred at disk power-on lifetime: 740 hours (30 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 25d+03:03:29.243 READ DMA EXT ef 10 02 00 00 00 a0 00 25d+03:03:29.242 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 25d+03:03:29.242 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 25d+03:03:29.241 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 25d+03:03:29.241 SET FEATURES [set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 671 - # 2 Short offline Completed without error 00% 667 - # 3 Short offline Completed without error 00% 667 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
January 2, 201313 yr Does the web access work initially upon reboot and then fails (if so after how long), or does it never work?
January 2, 201313 yr Author Does the web access work initially upon reboot and then fails (if so after how long), or does it never work? Web access initially worked, I havent rebooted since the initial build.
January 2, 201313 yr Does the web access work initially upon reboot and then fails (if so after how long), or does it never work? Web access initially worked, I havent rebooted since the initial build. I also have the same issue of webui dropping - haven't quite understood why yet. http://lime-technology.com/forum/index.php?topic=23274.0 I have seen more mentions of it on the forum.
January 2, 201313 yr It most probably got killed as a result of lack of memory.. Check if your syslog mentions OOM events. If so then check out the following thread: http://lime-technology.com/forum/index.php?topic=22971.0
January 2, 201313 yr Looks like a loose or bad SATA cable or port. Reseat the SATA cable and/or try a new cable.
January 3, 201313 yr Author Ok, I've shutdown the system. re-seated the cables and started back up. The web interface is back. Will see if these errors pop up again. Thanks for the help.
Archived
This topic is now archived and is closed to further replies.