crazynight Posted January 18, 2013 Share Posted January 18, 2013 could someone take a look at this report and give me some idea of whats going on the drive has failed but not sure why can I just format it and put it back or do I need to send it back? smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST1500DL003-9VT16L Serial Number: (removed) Firmware Version: CC98 User Capacity: 1,500,301,910,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Fri Jan 18 20:14:45 2013 Local time zone must be set--see zic m SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 612) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 254) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1033) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 52128656 3 Spin_Up_Time 0x0003 093 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 525 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 068 060 030 Pre-fail Always - 7015628 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 869 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 22 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 071 071 000 Old_age Always - 29 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 4295032833 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 074 068 045 Old_age Always - 26 (Min/Max 23/26) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 546 194 Temperature_Celsius 0x0022 026 040 000 Old_age Always - 26 (0 21 0 0) 195 Hardware_ECC_Recovered 0x001a 035 019 000 Old_age Always - 52128656 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 109878148333943 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1191269549 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2479323320 SMART Error Log Version: 1 ATA Error Count: 29 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 29 occurred at disk power-on lifetime: 188 hours (7 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 5d+06:08:34.694 READ DMA EXT 27 00 00 00 00 00 e0 00 5d+06:08:34.693 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 5d+06:08:34.693 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 5d+06:08:34.692 SET FEATURES [set transfer mode] 27 00 00 00 00 00 e0 00 5d+06:08:34.662 READ NATIVE MAX ADDRESS EXT Error 28 occurred at disk power-on lifetime: 188 hours (7 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 5d+06:08:31.330 READ DMA EXT 27 00 00 00 00 00 e0 00 5d+06:08:31.329 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 5d+06:08:31.329 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 5d+06:08:31.298 SET FEATURES [set transfer mode] 27 00 00 00 00 00 e0 00 5d+06:08:31.201 READ NATIVE MAX ADDRESS EXT Error 27 occurred at disk power-on lifetime: 188 hours (7 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 5d+06:08:27.957 READ DMA EXT 27 00 00 00 00 00 e0 00 5d+06:08:27.956 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 5d+06:08:27.955 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 5d+06:08:27.955 SET FEATURES [set transfer mode] 27 00 00 00 00 00 e0 00 5d+06:08:27.925 READ NATIVE MAX ADDRESS EXT Error 26 occurred at disk power-on lifetime: 188 hours (7 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 5d+06:08:24.583 READ DMA EXT 27 00 00 00 00 00 e0 00 5d+06:08:24.582 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 5d+06:08:24.582 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 5d+06:08:24.581 SET FEATURES [set transfer mode] 27 00 00 00 00 00 e0 00 5d+06:08:24.550 READ NATIVE MAX ADDRESS EXT Error 25 occurred at disk power-on lifetime: 188 hours (7 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 5d+06:08:21.219 READ DMA EXT 27 00 00 00 00 00 e0 00 5d+06:08:21.219 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 5d+06:08:21.218 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 5d+06:08:21.218 SET FEATURES [set transfer mode] 27 00 00 00 00 00 e0 00 5d+06:08:21.187 READ NATIVE MAX ADDRESS EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Quote Link to comment
dgaschk Posted January 19, 2013 Share Posted January 19, 2013 The errors could be cause by a bad or loose cable or SATA port. Or EM interference on the cable. The SATA port on the drive itself could be flakey. I'd run pre-clear on the drive and the use it. Quote Link to comment
crazynight Posted January 19, 2013 Author Share Posted January 19, 2013 forgot to say the drive is making a buzz....clicking sound from time to time Quote Link to comment
itimpi Posted January 19, 2013 Share Posted January 19, 2013 forgot to say the drive is making a buzz....clicking sound from time to time That definitely sounds as if the drive failure is likely to be terminal. Quote Link to comment
crazynight Posted January 19, 2013 Author Share Posted January 19, 2013 as its just 2 months old will download their testing tool and test the drive and do a return. off shopping for a replacement to get the array back up and running and fully protected again. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.