March 21, 201313 yr 1st pre-clear ** Changed attributes in files: /tmp/smart_start_sde /tmp/smart_finish_sde ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 199 200 51 ok 4011 Seek_Error_Rate = 100 200 0 ok 0 Load_Cycle_Count = 1 1 0 near_thresh 796570 Temperature_Celsius = 109 114 0 ok 41 No SMART attributes are FAILING_NOW 106 sectors were pending re-allocation before the start of the preclear. 111 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 45 sectors are pending re-allocation at the end of the preclear, a change of -61 in the number of sectors pending re-allocation. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. 2nd pre-clear ** Changed attributes in files: /tmp/smart_start_sde /tmp/smart_finish_sde ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Load_Cycle_Count = 1 1 0 near_thresh 796577 Temperature_Celsius = 108 112 0 ok 42 No SMART attributes are FAILING_NOW 67 sectors were pending re-allocation before the start of the preclear. 72 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 63 sectors are pending re-allocation at the end of the preclear, a change of -4 in the number of sectors pending re-allocation. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. 3rd pre-clear ** Changed attributes in files: /tmp/smart_start_sde /tmp/smart_finish_sde ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 198 199 51 ok 8251 Reallocated_Sector_Ct = 198 200 140 ok 43 Load_Cycle_Count = 1 1 0 near_thresh 796579 Temperature_Celsius = 110 107 0 ok 40 Reallocated_Event_Count = 167 200 0 ok 33 No SMART attributes are FAILING_NOW 63 sectors were pending re-allocation before the start of the preclear. 75 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 75 sectors are pending re-allocation at the end of the preclear, a change of 12 in the number of sectors pending re-allocation. 0 sectors had been re-allocated before the start of the preclear. 43 sectors are re-allocated at the end of the preclear, a change of 43 in the number of sectors re-allocated. extended smart after 3rd pre-clear === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (38400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 198 198 051 Pre-fail Always - 8251 3 Spin_Up_Time 0x0027 244 171 021 Pre-fail Always - 2766 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 840 5 Reallocated_Sector_Ct 0x0033 198 198 140 Pre-fail Always - 43 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 18118 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 139 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 48 193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 796588 194 Temperature_Celsius 0x0022 108 094 000 Old_age Always - 42 196 Reallocated_Event_Count 0x0032 167 167 000 Old_age Always - 33 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 97 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 60 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 199 199 000 Old_age Offline - 484 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 18116 3593194728 # 2 Extended offline Completed: read failure 90% 17493 3662235257 # 3 Short offline Completed: read failure 90% 17492 3662235257 # 4 Short offline Completed: read failure 90% 17140 3619484415 # 5 Short offline Completed without error 00% 12827 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. this drive was from my parity. replaced with new 2tb green. hw reliable is this disk, if i add it into array? regards, joseph
March 21, 201313 yr I would say that drive is nearly useless. There are constantly un-readable sectors on ever post-read cycle. There is a possibility it is a poor power supply to the drive causing the errors, but odds are higher it is the drive itself.
Archived
This topic is now archived and is closed to further replies.