I'm running 5.0-rc12a.

In the healt tab for SimpleFeatures v1.0.11 when i run disk self test for drive 2 I get:

 

ATA Error Count: 105 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

 

Error 105 occurred at disk power-on lifetime: 10275 hours (428 days + 3 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 99 a3 8a e0  Error: UNC at LBA = 0x008aa399 = 9085849

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 08 97 a3 8a e0 00      06:38:47.972  READ DMA EXT

  25 00 08 df aa 0c e0 00      06:38:47.911  READ DMA EXT

  c8 00 08 3f 91 75 ec 00      06:38:47.891  READ DMA

  c8 00 08 87 e2 6a ee 00      06:38:47.871  READ DMA

  c8 00 08 8f 1f d0 ec 00      06:38:47.851  READ DMA

 

Error 104 occurred at disk power-on lifetime: 8401 hours (350 days + 1 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 c1 cc 6d e0  Error: UNC at LBA = 0x006dccc1 = 7195841

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 70 57 cc 6d e0 00      05:14:50.667  READ DMA EXT

  27 00 00 00 00 00 e0 00      05:14:50.666  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 a0 00      05:14:48.606  IDENTIFY DEVICE

  ef 03 46 00 00 00 a0 00      05:14:48.548  SET FEATURES [set transfer mode]

  27 00 00 00 00 00 e0 00      05:14:48.547  READ NATIVE MAX ADDRESS EXT

 

Error 103 occurred at disk power-on lifetime: 8401 hours (350 days + 1 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 c1 cc 6d e0  Error: UNC at LBA = 0x006dccc1 = 7195841

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 70 57 cc 6d e0 00      05:14:44.434  READ DMA EXT

  27 00 00 00 00 00 e0 00      05:14:43.913  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 a0 00      05:14:48.606  IDENTIFY DEVICE

  ef 03 46 00 00 00 a0 00      05:14:48.548  SET FEATURES [set transfer mode]

  27 00 00 00 00 00 e0 00      05:14:48.547  READ NATIVE MAX ADDRESS EXT

 

Error 102 occurred at disk power-on lifetime: 8401 hours (350 days + 1 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 c1 cc 6d e0  Error: UNC at LBA = 0x006dccc1 = 7195841

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 70 57 cc 6d e0 00      05:14:44.434  READ DMA EXT

  25 00 08 1f d6 37 e0 00      05:14:43.913  READ DMA EXT

  25 00 08 8f ef 9a e0 00      05:14:43.823  READ DMA EXT

  25 00 28 9f c4 d6 e0 00      05:14:43.803  READ DMA EXT

  25 00 58 c7 8c d6 e0 00      05:14:43.783  READ DMA EXT

 

Error 101 occurred at disk power-on lifetime: 8391 hours (349 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 a7 cc 78 e0  Error: UNC at LBA = 0x0078cca7 = 7916711

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 00 1f cb 78 e0 00      01:37:51.193  READ DMA EXT

  27 00 00 00 00 00 e0 00      01:37:51.192  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 a0 00      01:37:51.192  IDENTIFY DEVICE

  ef 03 46 00 00 00 a0 00      01:37:51.134  SET FEATURES [set transfer mode]

  27 00 00 00 00 00 e0 00      01:37:51.133  READ NATIVE MAX ADDRESS EXT

 

Just to clarify, the server works fine, so are the drives... but the SMART status on TWO DRIVES worries me.

Is this a plugin issue or a real problem? How can I find out for sure?

Disk 3

 

Attached to port: sdn

Num

Test Description

Status

Remaining

LifeTime(hours)

LBA of first error

 

 

1

Short offline

Completed: unknown failure

90%

14102

238316519

 

 

 

2

Short offline

Completed: unknown failure

90%

14094

686677484

 

 

3

Extended offline

Completed: unknown failure

90%

14094

148646063

 

Disk 2 Error Log

 

ATA Error Count: 105 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

 

Error 105 occurred at disk power-on lifetime: 10275 hours (428 days + 3 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 99 a3 8a e0  Error: UNC at LBA = 0x008aa399 = 9085849

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 08 97 a3 8a e0 00      06:38:47.972  READ DMA EXT

  25 00 08 df aa 0c e0 00      06:38:47.911  READ DMA EXT

  c8 00 08 3f 91 75 ec 00      06:38:47.891  READ DMA

  c8 00 08 87 e2 6a ee 00      06:38:47.871  READ DMA

  c8 00 08 8f 1f d0 ec 00      06:38:47.851  READ DMA

 

Error 104 occurred at disk power-on lifetime: 8401 hours (350 days + 1 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 c1 cc 6d e0  Error: UNC at LBA = 0x006dccc1 = 7195841

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 70 57 cc 6d e0 00      05:14:50.667  READ DMA EXT

  27 00 00 00 00 00 e0 00      05:14:50.666  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 a0 00      05:14:48.606  IDENTIFY DEVICE

  ef 03 46 00 00 00 a0 00      05:14:48.548  SET FEATURES [set transfer mode]

  27 00 00 00 00 00 e0 00      05:14:48.547  READ NATIVE MAX ADDRESS EXT

 

Error 103 occurred at disk power-on lifetime: 8401 hours (350 days + 1 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 c1 cc 6d e0  Error: UNC at LBA = 0x006dccc1 = 7195841

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 70 57 cc 6d e0 00      05:14:44.434  READ DMA EXT

  27 00 00 00 00 00 e0 00      05:14:43.913  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 a0 00      05:14:48.606  IDENTIFY DEVICE

  ef 03 46 00 00 00 a0 00      05:14:48.548  SET FEATURES [set transfer mode]

  27 00 00 00 00 00 e0 00      05:14:48.547  READ NATIVE MAX ADDRESS EXT

 

Error 102 occurred at disk power-on lifetime: 8401 hours (350 days + 1 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 c1 cc 6d e0  Error: UNC at LBA = 0x006dccc1 = 7195841

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 70 57 cc 6d e0 00      05:14:44.434  READ DMA EXT

  25 00 08 1f d6 37 e0 00      05:14:43.913  READ DMA EXT

  25 00 08 8f ef 9a e0 00      05:14:43.823  READ DMA EXT

  25 00 28 9f c4 d6 e0 00      05:14:43.803  READ DMA EXT

  25 00 58 c7 8c d6 e0 00      05:14:43.783  READ DMA EXT

 

Error 101 occurred at disk power-on lifetime: 8391 hours (349 days + 15 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  40 51 00 a7 cc 78 e0  Error: UNC at LBA = 0x0078cca7 = 7916711

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  25 00 00 1f cb 78 e0 00      01:37:51.193  READ DMA EXT

  27 00 00 00 00 00 e0 00      01:37:51.192  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 a0 00      01:37:51.192  IDENTIFY DEVICE

  ef 03 46 00 00 00 a0 00      01:37:51.134  SET FEATURES [set transfer mode]

  27 00 00 00 00 00 e0 00      01:37:51.133  READ NATIVE MAX ADDRESS EXT

 

 

Interestingly, when I click on the Smart Status button, on the drive setting page, it reports SMART STATUS passed (although it reports a fail before I click on the button).

Attached to port: sdo

 

ID# ATTRIBUTE NAME FLAG VALUE WORST THRESH TYPE UPDATED FAILED RAW VALUE

1 Raw Read Error Rate 0x000f 119 071 006 Pre-fail Always Never 204491176

3 Spin Up Time 0x0003 093 092 000 Pre-fail Always Never 0

4 Start Stop Count 0x0032 097 097 020 Old age Always Never 3758

5 Reallocated Sector Ct 0x0033 096 096 036 Pre-fail Always Never 176

7 Seek Error Rate 0x000f 054 044 030 Pre-fail Always Never 3075367678354

9 Power On Hours 0x0032 085 085 000 Old age Always Never 13477

10 Spin Retry Count 0x0013 065 018 097 Pre-fail Always Now 0

12 Power Cycle Count 0x0032 100 100 020 Old age Always Never 178

187 Reported Uncorrect 0x0032 001 001 000 Old age Always Never 11016

189 High Fly Writes 0x003a 100 100 000 Old age Always Never 0

190 Airflow Temperature Cel 0x0022 064 055 045 Old age Always Never 36 (3 240 36 24)

194 Temperature Celsius 0x0022 036 045 000 Old age Always Never 36 (0 7 0 0)

195 Hardware ECC Recovered 0x001a 053 046 000 Old age Always Never 219787201

197 Current Pending Sector 0x0012 100 100 000 Old age Always Never 0

198 Offline Uncorrectable 0x0010 100 100 000 Old age Offline Never 0

199 UDMA CRC Error Count 0x003e 200 200 000 Old age Always Never 0

200 Multi Zone Error Rate 0x0000 100 253 000 Old age Offline Never 0

202 Data Address Mark Errs 0x0032 100 253 000 Old age Always Never 0

 

 

spin retry count line is red for disk two