DToX Posted March 16, 2014 Share Posted March 16, 2014 I can't get my Mobo Temp to show and i'm assuming it's from this Driver `f71882fg': * ISA bus, address 0x480 Chip `Fintek F71889A Super IO Sensors' (confidence: 9) Is there anyway to get this working corrrectly? root@Tower:~# sensors k10temp-pci-00c3 Adapter: PCI adapter CPU Temp: +20.8°C (high = +70.0°C) (crit = +70.0°C, hyst = +67.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: 124.95 W (crit = 124.95 W) root@Tower:~# Sensor-detect output root@Tower:/tmp# perl sensors-detect # sensors-detect revision $Revision$ # System: MSI MS-7693 [2.0] # Board: MSI 970A-G46 (MS-7693) This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): yes Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... Success! (driver `k10temp') AMD Family 16h thermal sensors... No AMD Family 15h power sensors... Success! (driver `fam15h_power') AMD Family 16h power sensors... No Intel digital thermal sensor... No Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): yes Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... Yes Found `Fintek F71889A Super IO Sensors' Success! (address 0x480, driver `f71882fg') Some systems (mainly servers) implement IPMI, a set of common interfaces through which system health data may be retrieved, amongst other things. We first try to get the information from SMBIOS. If we don't find it there, we have to read from arbitrary I/O ports to probe for such interfaces. This is normally safe. Do you want to scan for IPMI interfaces? (YES/no): yes Probing for `IPMI BMC KCS' at 0xca0... No Probing for `IPMI BMC SMIC' at 0xca8... No Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): yes Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): yes Using driver `i2c-piix4' for device 0000:00:14.0: ATI Technologies Inc SB600/SB700/SB800 SMBus Module i2c-dev loaded successfully. Next adapter: SMBus PIIX4 adapter at 0b00 (i2c-0) Do you want to scan it? (yes/NO/selectively): yes Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Probing for `EDID EEPROM'... No Client found at address 0x51 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Client found at address 0x52 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Client found at address 0x53 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `fam15h_power' (autoloaded): * Chip `AMD Family 15h power sensors' (confidence: 9) Driver `k10temp' (autoloaded): * Chip `AMD Family 15h thermal sensors' (confidence: 9) Driver `f71882fg': * ISA bus, address 0x480 Chip `Fintek F71889A Super IO Sensors' (confidence: 9) Warning: the required module f71882fg is not currently installed on your system. Check http://www.lm-sensors.org/wiki/Devices for driver availability. No modules to load, skipping modules configuration. Unloading i2c-dev... OK root@Tower:/tmp# Quote Link to comment
dlandon Posted March 16, 2014 Share Posted March 16, 2014 There is an issue with the CPU and MB temperatures. This line in the SystemTemps.php sorts the temperatures and the lowest one always shows first (left position) on the webpage. exec("sensors -A|awk '/^CPU Temp/ {print $3*1}; /^M\/?B Temp/ {print $3*1}'",$temp); No matter which temperature is associated with the CPU and MB, the lowest temperature will always show first on the left. In my case the MB temp is lower so it shows in the CPU temperature position. Really a minor issue, but may cause some consternation when trying to get the temperatures to show in the correct positions. Quote Link to comment
DToX Posted March 16, 2014 Share Posted March 16, 2014 There is an issue with the CPU and MB temperatures. This line in the SystemTemps.php sorts the temperatures and the lowest one always shows first (left position) on the webpage. exec("sensors -A|awk '/^CPU Temp/ {print $3*1}; /^M\/?B Temp/ {print $3*1}'",$temp); No matter which temperature is associated with the CPU and MB, the lowest temperature will always show first on the left. In my case the MB temp is lower so it shows in the CPU temperature position. Really a minor issue, but may cause some consternation when trying to get the temperatures to show in the correct positions. Well that is good to know but I can't even read my mobo temp, I think from what I have gathered is that the linux kernel doesn't support the driver needed for my mobo so I cannot get the temps Quote Link to comment
RobJ Posted March 17, 2014 Share Posted March 17, 2014 Well that is good to know but I can't even read my mobo temp, I think from what I have gathered is that the linux kernel doesn't support the driver needed for my mobo so I cannot get the temps DToX, he wasn't actually responding to you, he was announcing an issue he had found, one that should be straight forward to fix. I can't get my Mobo Temp to show and i'm assuming it's from this Driver `f71882fg': * ISA bus, address 0x480 Chip `Fintek F71889A Super IO Sensors' (confidence: 9) Is there anyway to get this working corrrectly? root@Tower:~# sensors k10temp-pci-00c3 Adapter: PCI adapter CPU Temp: +20.8°C (high = +70.0°C) (crit = +70.0°C, hyst = +67.0°C) I'm actually happy that you have the same issue I have, needing the Fintek f71882fg driver. I suspect you haven't read my post above (found here). Now that I know someone else needs 'f71882fg', I'll ask Tom if he can add it to UnRAID (didn't want to before if I was the only one). Since yours is very similar except your board uses the k10temp chipset instead of the k8temp chipset, I think you can probably use the sensors.conf file I posted, except change "k8temp-*" to "k10temp-*". Make sure you use an editor that keeps the linux line endings. That should at least give you 2 CPU temps for now, until f71882fg support is added. Be aware though that many users have reported that the k8temp and k10temp chipsets are notoriously unreliable for true temps. Works fine for me though. Quote Link to comment
DToX Posted March 18, 2014 Share Posted March 18, 2014 Well that is good to know but I can't even read my mobo temp, I think from what I have gathered is that the linux kernel doesn't support the driver needed for my mobo so I cannot get the temps DToX, he wasn't actually responding to you, he was announcing an issue he had found, one that should be straight forward to fix. I can't get my Mobo Temp to show and i'm assuming it's from this Driver `f71882fg': * ISA bus, address 0x480 Chip `Fintek F71889A Super IO Sensors' (confidence: 9) Is there anyway to get this working corrrectly? root@Tower:~# sensors k10temp-pci-00c3 Adapter: PCI adapter CPU Temp: +20.8°C (high = +70.0°C) (crit = +70.0°C, hyst = +67.0°C) I'm actually happy that you have the same issue I have, needing the Fintek f71882fg driver. I suspect you haven't read my post above (found here). Now that I know someone else needs 'f71882fg', I'll ask Tom if he can add it to UnRAID (didn't want to before if I was the only one). Since yours is very similar except your board uses the k10temp chipset instead of the k8temp chipset, I think you can probably use the sensors.conf file I posted, except change "k8temp-*" to "k10temp-*". Make sure you use an editor that keeps the linux line endings. That should at least give you 2 CPU temps for now, until f71882fg support is added. Be aware though that many users have reported that the k8temp and k10temp chipsets are notoriously unreliable for true temps. Works fine for me though. Thank you that was helpful, anyway fingers crossed on a future update Quote Link to comment
FreeMan Posted March 30, 2014 Share Posted March 30, 2014 I'm running a Gigabyte F2A88XM-D3H mobo with an AMD A6 5400K CPU. I found this link http://ubuntuforums.org/showthread.php?t=2201555 and this one http://www.phoronix.com/forums/showthread.php?96788-Gigabyte-F2A88XM-D3H-AMD-A88X/page3 that both indicated that I needed to use modprobe it87 force_id=0x8728. Having done that, sensors now reports: k10temp-pci-00c3 Adapter: PCI adapter MB Temp: +9.4 C (high = +70.0 C) (crit = +80.0 C, hyst = +79.0 C) it8728-isa-0228 Adapter: ISA adapter in0: +1.00 V (min = +0.00 V, max = +3.06 V) in1: +1.49 V (min = +0.00 V, max = +3.06 V) in2: +2.02 V (min = +0.00 V, max = +3.06 V) in3: +2.02 V (min = +0.00 V, max = +3.06 V) in4: +2.00 V (min = +0.00 V, max = +3.06 V) in5: +2.22 V (min = +0.00 V, max = +3.06 V) in6: +2.22 V (min = +0.00 V, max = +3.06 V) 3VSB: +3.36 V (min = +0.00 V, max = +6.12 V) Vbat: +3.02 V fan1: 1917 RPM (min = 10 RPM) fan2: 0 RPM (min = 10 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) fan5: 0 RPM (min = 0 RPM) temp1: +29.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor temp2: -8.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor temp3: +30.0 C (low = +0.0 C, high = +60.0 C) sensor = Intel PECI intrusion0: ALARM I ended up with this in my sensors.conf: # sensor configuration chip "k10temp-*" #chip "it8728-isa-0028" label temp1 "MB Temp" label temp3 "CPU Temp" With the first "chip" line in effect, I get the somewhat ridiculously low reading in the single digits © as a temp being displayed in Dynamix. If I uncomment the 2nd "chip" line, instead, I get no readings showing up. The values from the it8728 chip seem to be accurate, or at least reasonable, how do I get them to display instead of the values from the k10temp chip? (As a side note, how do I get a nicely formatted word as a link, instead of displaying the full link? I know how to do <a href="url">text</a> in HTML, but how do I do it in BBCode?) Quote Link to comment
RobJ Posted March 31, 2014 Share Posted March 31, 2014 I'm running a Gigabyte F2A88XM-D3H mobo with an AMD A6 5400K CPU. I found this link http://ubuntuforums.org/showthread.php?t=2201555 and this one http://www.phoronix.com/forums/showthread.php?96788-Gigabyte-F2A88XM-D3H-AMD-A88X/page3 that both indicated that I needed to use modprobe it87 force_id=0x8728. Having done that, sensors now reports: k10temp-pci-00c3 Adapter: PCI adapter MB Temp: +9.4 C (high = +70.0 C) (crit = +80.0 C, hyst = +79.0 C) it8728-isa-0228 Adapter: ISA adapter in0: +1.00 V (min = +0.00 V, max = +3.06 V) in1: +1.49 V (min = +0.00 V, max = +3.06 V) in2: +2.02 V (min = +0.00 V, max = +3.06 V) in3: +2.02 V (min = +0.00 V, max = +3.06 V) in4: +2.00 V (min = +0.00 V, max = +3.06 V) in5: +2.22 V (min = +0.00 V, max = +3.06 V) in6: +2.22 V (min = +0.00 V, max = +3.06 V) 3VSB: +3.36 V (min = +0.00 V, max = +6.12 V) Vbat: +3.02 V fan1: 1917 RPM (min = 10 RPM) fan2: 0 RPM (min = 10 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) fan5: 0 RPM (min = 0 RPM) temp1: +29.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor temp2: -8.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor temp3: +30.0 C (low = +0.0 C, high = +60.0 C) sensor = Intel PECI intrusion0: ALARM I ended up with this in my sensors.conf: # sensor configuration chip "k10temp-*" #chip "it8728-isa-0028" label temp1 "MB Temp" label temp3 "CPU Temp" With the first "chip" line in effect, I get the somewhat ridiculously low reading in the single digits © as a temp being displayed in Dynamix. If I uncomment the 2nd "chip" line, instead, I get no readings showing up. The values from the it8728 chip seem to be accurate, or at least reasonable, how do I get them to display instead of the values from the k10temp chip? It looks like you used "it8728-isa-0028" instead of "it8728-isa-0228". Safer yet, try "it8728-isa-*". (As a side note, how do I get a nicely formatted word as a link, instead of displaying the full link? I know how to do <a href="url">text</a> in HTML, but how do I do it in BBCode?) Simple, click the 'Insert Hyperlink' button above your edit message box (has an earth icon, located below the Italic button). After the initial URL, add an equal sign and the link, then the display text between the pair of bracketed 'URL's. Like the following: [url=http://ubuntuforums.org/showthread.php?t=2201555]Ubuntu forum link[/url] Displays as: Ubuntu forum link Quote Link to comment
FreeMan Posted March 31, 2014 Share Posted March 31, 2014 It looks like you used "it8728-isa-0028" instead of "it8728-isa-0228". Safer yet, try "it8728-isa-*". Winner, winner, chicken dinner!!! Thanks Rob, that was the ticket. Despite wearing contacts, we all need 4 eyes. Displays as: Ubuntu forum link Thanks - don't know why I didn't think of that... Quote Link to comment
maspiter Posted May 6, 2014 Share Posted May 6, 2014 I've followed the guide, made the sensors.conf file but I still don't get the temps displayed. When running sensors, it shows the labels have changed to "CPU temp" and "MB temp" though. Any thoughts? Quote Link to comment
megalodon Posted June 18, 2014 Share Posted June 18, 2014 Anyone found a way to use lm-sensors on X9SCM-F but with unRAID running under ESXi? In that case modprobe w83627ehf complains 'no such device found'. Apparently such devices are not passed-through to a VM. I tried with other modules, but they do not work either. Maybe the only way is to read system temp via IPMI linux tools? Edit: I found this: http://www.thomas-krenn.com/en/wiki/Supermicro_X9SCM-F_Motherboard We would require FreeIPMI package then and modified/alternative version of System Temp plugin for IPMI. I didn't get the X9SCM-F working under ESXi, but I did get it working on bare metal using the following steps: My go file addition: modprobe w83627ehf cp /boot/custom/sensors.d/sensors.conf /etc/sensors.d cp /boot/custom/sensors.d/sensors.conf /etc/sensors3.conf My /boot/custom/sensors.d/sensors.conf file: chip "w83627ehf-*" "w83627dhg-*" "w83667hg-*" "nct6775-*" "nct6776-*" label in0 "Vcore" label in2 "AVCC" label in3 "+3.3V" label in7 "3VSB" label in8 "Vbat" label temp2 "CPU Temp" label temp1 "MB Temp" set in2_min 3.3 * 0.90 set in2_max 3.3 * 1.10 set in3_min 3.3 * 0.90 set in3_max 3.3 * 1.10 set in7_min 3.3 * 0.90 set in7_max 3.3 * 1.10 set in8_min 3.0 * 0.90 set in8_max 3.3 * 1.10 Thanks for this Ogi it was a great help to me. As Im using a later version of Dynamix WebGui all I had to do was make a sensors.conf file using a text editor and place your settings in it and just add "mod probe w83627ehf" to my go file using my text editor. The sensors.conf file is in a different place from where it used to be when using the Dynamix system temp plugin from the webGui. For a new user to unRAID like me it helps so much when users post helpful things like you did, so thanks. Im using a Supermicro X9SCM-iF Motherboard but a the temp sensors are very confusing on this board. It says Im getting 29.5 on the motherboard and 35 degree's C on the CPU using your settings in the dynamix webGui with the system temp plugin. But the IPMI says 29c system temp, 35c peripheral temp and CPU temp low. When I spoke to Supermicro Tech support last year they told me the system temp is for the motherboard sensor as correctly shown in the Dynamix WebGui but the 35c is for the peripherals like the HBA cards etc and not the CPU as the CPU just has low, med or high so Im wondering if the CPU temp of 35c showing in the Dynamix webGui is actually for the CPU or not. Quote Link to comment
optiman Posted June 20, 2014 Share Posted June 20, 2014 I'm just getting started with setting up the sensors.conf file for my new rig. I have the Gigabyte GA-X58A-UD3R_rev2 motherboard. Does anyone else have this same MB and perhaps can share the config file to save me some time? Update: I was able to get this working. I've attached my sensors.conf file, in case anyone has my same MB. In addition, I share the output, in case I have done anything incorrectly. That said, the temps are showing up and they look to be correct. my sensors.conf: # sensors config for Gigabyte GA-X58A-UD3R_rev2 chip "it8720-isa-0290" label temp1 "CPU Temp" label temp2 "MB Temp" ignore temp3 chip "coretemp-isa-0000" My Go file: #!/bin/bash # Start the Management Utility /usr/local/sbin/emhttp & # Update Sensors Config cp /boot/custom/sensors.d/sensors.conf /etc/sensors.d/sensors.conf modprobe coretemp modprobe it87 /usr/bin/sensors -s sensors command line output: root@Tower:~# sensors coretemp-isa-0000 Adapter: ISA adapter Core 0: +46.0 C (high = +80.0 C, crit = +100.0 C) Core 1: +47.0 C (high = +80.0 C, crit = +100.0 C) Core 2: +48.0 C (high = +80.0 C, crit = +100.0 C) Core 3: +45.0 C (high = +80.0 C, crit = +100.0 C) it8720-isa-0290 Adapter: ISA adapter in0: +0.93 V (min = +0.00 V, max = +4.08 V) in1: +1.58 V (min = +0.00 V, max = +4.08 V) in2: +3.38 V (min = +0.00 V, max = +4.08 V) +5V: +3.01 V (min = +0.00 V, max = +4.08 V) in4: +0.34 V (min = +0.00 V, max = +4.08 V) in5: +3.10 V (min = +0.00 V, max = +4.08 V) in6: +0.08 V (min = +0.00 V, max = +4.08 V) 5VSB: +2.98 V (min = +0.00 V, max = +4.08 V) Vbat: +3.17 V fan1: 1885 RPM (min = 10 RPM) fan2: 1250 RPM (min = 0 RPM) fan3: 1730 RPM (min = 0 RPM) fan4: 1394 RPM (min = 0 RPM) CPU Temp: +48.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor MB Temp: +45.0 C (low = +127.0 C, high = +60.0 C) sensor = thermal diode intrusion0: ALARM root@Tower:~# Very nice to see temps again. sensors.conf Quote Link to comment
megalodon Posted June 21, 2014 Share Posted June 21, 2014 As its always hard to find information about unRAID plugins etc without sometimes reading through loads of forums posts, it maybe a good idea to have a list of motherboards that forum users have already setup with the system temp plugin, sensors.confg information, with a link from each motherboard to the sensors.conf information and the go information. Just a thought but it would make it so much easier to just click a link and have the information to hand. Quote Link to comment
dazzam Posted July 9, 2014 Share Posted July 9, 2014 My two cents Attached my simple sensors.conf for HP microserver NL36. Only CPU temp Thanks marrajon! btw: what sensor driver did you use with modprobe in the go 'file' ? I'm hoping the N54L uses the same driver as your NL36 so I don't have to worry about installing the perl package (I presume the go 'file' mentioned in the directions, is the one in /boot/config/ ) cheers, DM Quote Link to comment
Necrotic Posted July 13, 2014 Share Posted July 13, 2014 Back in the SF thread we also ran into issues of keeping track of sensor files, I suggested that a wiki page should be added for it where people can append some of the files but no one took me up. I have the sensor file ready for my mobo if anyone wants to create the wiki/thread for it. Quote Link to comment
umax Posted October 29, 2014 Share Posted October 29, 2014 Ok, I have a few basic problems here regarding getting the temp senosors done. I have Supermicro X8SIL board, bellow is console response to "sensors". root@Tower:~# sensors coretemp-isa-0000 Adapter: ISA adapter Core 0: +35.0 C (high = +89.0 C, crit = +105.0 C) Core 2: +35.0 C (high = +89.0 C, crit = +105.0 C) Tried installing perl package to get "sensors-detect" output, but I stopped here as I don't know how to successfully install perl package? Where is Dynamix system Temp plugin located and what/how do I edit it as it is explained bellow; - Or for Dynamix, you can modify the Dynamix System Temp plugin itself, by locating the line ending with "# perl scripting" and replacing "no-install" with "do-install". Then re-install the plugin or reboot. After that do I need only sensors.conf file or do I need to edit "go" file also? Never done that before, so I feel a bit overwhelmed. Quote Link to comment
optiman Posted October 29, 2014 Share Posted October 29, 2014 Have you read the first post in this thread, which tells you to go read the wiki? I think step 5 talks about what directory the plugin resides. Best if you read and follow the instructions in the wiki. Not sure if the wiki says this or not, but for my Windows rig I use Notepad++ to edit. Quote Link to comment
umax Posted October 30, 2014 Share Posted October 30, 2014 Have you read the first post in this thread, which tells you to go read the wiki? I think step 5 talks about what directory the plugin resides. Best if you read and follow the instructions in the wiki. Not sure if the wiki says this or not, but for my Windows rig I use Notepad++ to edit. Sure, the step 6 which I posted above talks about installing perl package, this is where I stopped as I dont know how(and where) to edit plugin to force perl installation. Step 5 in Wiki talks about where to save sensors.conf file. Ok, I have notepad++ so thanks for letting me know about "go" file. Quote Link to comment
optiman Posted October 30, 2014 Share Posted October 30, 2014 Ok, first run sensors-detect on the console nad see if you get anything. if not sure what you are looking at, post the output here so we can see it. Look at my output, about 6 posts above as a reference. If you do get the output you are looking for, then you already have what you need to move to the next step. The reason it tells you to try it first is because other packages may have already installed perl or one of the other packages that will allow senors ro work. If you don't get the output you want, then simple locate the plugin on your boot (flash) drive and use Notepad++ to change the one line - replace don't install with do install. Save and reboot. Go back to step 6 and run sensors-detect again. If it now works, go to step 7. you use Notepadd++ as any other TEXT file editor. Just open Notepad++ and then open the plugin file, then scroll down until you find the line mentioned in step 6 and change it - save it and exit. Reboot and see if it works. Quote Link to comment
umax Posted November 1, 2014 Share Posted November 1, 2014 i have manged to install Perl and here is the output of "sensors-detect". I really don't know what to look for tho UNRAiD login: root Linux 3.9.11p-unRAID. root@UNRAiD:~# sensors-detect # sensors-detect revision 6170 (2013-05-20 21:25:22 +0200) # System: Supermicro X8SIL [0123456789] This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): Yes Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No AMD Family 16h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): Yes Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... Yes Found `Winbond W83627DHG Super IO Sensors' Success! (address 0xa10, driver `w83627ehf') Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Some systems (mainly servers) implement IPMI, a set of common interfaces through which system health data may be retrieved, amongst other things. We first try to get the information from SMBIOS. If we don't find it there, we have to read from arbitrary I/O ports to probe for such interfaces. This is normally safe. Do you want to scan for IPMI interfaces? (YES/no): Yes Found `IPMI BMC KCS' at 0xca2... Success! (confidence 8, driver `to-be-written') Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): Yes Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): Yes Using driver `i2c-i801' for device 0000:00:1f.3: Intel 3400/5 Series (PCH) Module i2c-dev loaded successfully. Next adapter: SMBus I801 adapter at 0400 (i2c-0) Do you want to scan it? (YES/no/selectively): Yes Client found at address 0x18 Probing for `Analog Devices ADM1021'... No Probing for `Analog Devices ADM1021A/ADM1023'... No Probing for `Maxim MAX1617'... No Probing for `Maxim MAX1617A'... No Probing for `Maxim MAX1668'... No Probing for `Maxim MAX1805'... No Probing for `Maxim MAX1989'... No Probing for `Maxim MAX6655/MAX6656'... No Probing for `TI THMC10'... No Probing for `National Semiconductor LM84'... No Probing for `Genesys Logic GL523SM'... No Probing for `Onsemi MC1066'... No Probing for `Maxim MAX1618'... No Probing for `Maxim MAX1619'... No Probing for `National Semiconductor LM82/LM83'... No Probing for `Maxim MAX6654'... No Probing for `Maxim MAX6690'... No Probing for `Maxim MAX6680/MAX6681'... No Probing for `Maxim MAX6695/MAX6696'... No Probing for `Texas Instruments AMC6821'... No Probing for `National Semiconductor LM95234'... No Probing for `National Semiconductor LM95245'... No Probing for `National Semiconductor LM64'... No Probing for `SMSC EMC1047'... No Probing for `SMSC EMC1402'... No Probing for `SMSC EMC1403'... No Probing for `SMSC EMC1404'... No Probing for `ST STTS424'... No Probing for `ST STTS424E'... No Probing for `ST STTS2002'... No Probing for `ST STTS3000'... No Probing for `NXP SE97/SE97B'... No Probing for `NXP SE98'... No Probing for `Analog Devices ADT7408'... No Probing for `IDT TS3000/TSE2002'... No Probing for `Maxim MAX6604'... No Probing for `Microchip MCP9804'... No Probing for `Microchip MCP98242'... No Probing for `Microchip MCP98243'... No Probing for `Microchip MCP98244'... No Probing for `Microchip MCP9843'... No Probing for `ON CAT6095/CAT34TS02'... Success! (confidence 5, driver `jc42') Probing for `Atmel AT30TS00'... No Client found at address 0x1a Probing for `Analog Devices ADM1021'... No Probing for `Analog Devices ADM1021A/ADM1023'... No Probing for `Maxim MAX1617'... No Probing for `Maxim MAX1617A'... No Probing for `Maxim MAX1668'... No Probing for `Maxim MAX1805'... No Probing for `Maxim MAX1989'... No Probing for `Maxim MAX6655/MAX6656'... No Probing for `TI THMC10'... No Probing for `National Semiconductor LM84'... No Probing for `Genesys Logic GL523SM'... No Probing for `Onsemi MC1066'... No Probing for `Maxim MAX1618'... No Probing for `Maxim MAX1619'... No Probing for `National Semiconductor LM82/LM83'... No Probing for `Maxim MAX6654'... No Probing for `Maxim MAX6690'... No Probing for `Maxim MAX6680/MAX6681'... No Probing for `Maxim MAX6695/MAX6696'... No Probing for `Texas Instruments AMC6821'... No Probing for `ST STTS424'... No Probing for `ST STTS424E'... No Probing for `ST STTS2002'... No Probing for `ST STTS3000'... No Probing for `NXP SE97/SE97B'... No Probing for `NXP SE98'... No Probing for `Analog Devices ADT7408'... No Probing for `IDT TS3000/TSE2002'... No Probing for `Maxim MAX6604'... No Probing for `Microchip MCP9804'... No Probing for `Microchip MCP98242'... No Probing for `Microchip MCP98243'... No Probing for `Microchip MCP98244'... No Probing for `Microchip MCP9843'... No Probing for `ON CAT6095/CAT34TS02'... Success! (confidence 5, driver `jc42') Probing for `Atmel AT30TS00'... No Client found at address 0x48 Probing for `National Semiconductor LM75'... No Probing for `National Semiconductor LM75A'... No Probing for `Dallas Semiconductor DS75'... No Probing for `National Semiconductor LM77'... No Probing for `Analog Devices ADT7410/ADT7420'... No Probing for `Analog Devices ADT7411'... No Probing for `Maxim MAX6642'... No Probing for `National Semiconductor LM73'... No Probing for `National Semiconductor LM92'... No Probing for `National Semiconductor LM76'... No Probing for `Maxim MAX6633/MAX6634/MAX6635'... No Probing for `NXP/Philips SA56004'... No Probing for `SMSC EMC1023'... No Probing for `SMSC EMC1043'... No Probing for `SMSC EMC1053'... No Probing for `SMSC EMC1063'... No Client found at address 0x50 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Probing for `EDID EEPROM'... No Client found at address 0x52 Probing for `Analog Devices ADM1033'... No Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `w83627ehf': * ISA bus, address 0xa10 Chip `Winbond W83627DHG Super IO Sensors' (confidence: 9 ) Driver `jc42': * Bus `SMBus I801 adapter at 0400' Busdriver `i2c_i801', I2C address 0x18 Chip `ON CAT6095/CAT34TS02' (confidence: 5) * Bus `SMBus I801 adapter at 0400' Busdriver `i2c_i801', I2C address 0x1a Chip `ON CAT6095/CAT34TS02' (confidence: 5) Driver `to-be-written': * ISA bus, address 0xca2 Chip `IPMI BMC KCS' (confidence: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) Warning: the required module jc42 is not currently installed on your system. If it is built into the kernel then it's OK. Otherwise, check http://www.lm-sensors.org/wiki/Devices for driver availability. Note: there is no driver for IPMI BMC KCS yet. Check http://www.lm-sensors.org/wiki/Devices for updates. Do you want to generate /etc/sysconfig/lm_sensors? (yes/NO): yes Copy prog/init/lm_sensors.init to /etc/init.d/lm_sensors for initialization at boot time. You should now start the lm_sensors service to load the required kernel modules. Unloading i2c-dev... OK I have accidentally put YES to "Enter [NO] to automatically generate the config file (last prompt)". Is this bad or how can I undo it? Do you want to generate /etc/sysconfig/lm_sensors? (yes/NO): yes Copy prog/init/lm_sensors.init to /etc/init.d/lm_sensors for initialization at boot time. You should now start the lm_sensors service to load the required kernel modules. Unloading i2c-dev... OK Quote Link to comment
optiman Posted November 1, 2014 Share Posted November 1, 2014 I could be wrong and you will want Bonienl to confirm, but I would not worry about saying YES to creating the config file. If it were me, I would just continue to step 8. Make sure your sensors.conf file is correct, edit your GO file and reboot. Quote Link to comment
bonienl Posted November 2, 2014 Author Share Posted November 2, 2014 Indeed no worries on that last 'yes' (this is reset upon reboot). Add the following to your "go" file and reboot your system # Add temperature modules modprobe coretemp modprobe w83627ehf /usr/bin/sensors -s After reboot do a "sensors" command and create your sensors.conf file as per wiki. Quote Link to comment
umax Posted November 2, 2014 Share Posted November 2, 2014 thanks to both, that did it!!! i now have both temps showing up on Dynamix! Quote Link to comment
optiman Posted November 2, 2014 Share Posted November 2, 2014 glad it's working. I assume the temps look correct to you. Some people have to switch the labels around in sensors.conf so cpu is actually the cpu, etc. I didn't have to do that for mine. What is really awesome is the announcement that Dynamix will now be included with V6! That is so cool - this completes unraid IMO. Quote Link to comment
MyKroFt Posted November 2, 2014 Share Posted November 2, 2014 having problems getting my sensor.conf file correct - the labels are not getting changed: sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +27.8 C (crit = +95.0 C) temp2: +29.8 C (crit = +95.0 C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +24.0 C (high = +74.0 C, crit = +94.0 C) Core 0: +22.0 C (high = +74.0 C, crit = +94.0 C) Core 1: +23.0 C (high = +74.0 C, crit = +94.0 C) Core 2: +18.0 C (high = +74.0 C, crit = +94.0 C) Core 3: +21.0 C (high = +74.0 C, crit = +94.0 C) nct6776-isa-0a30 Adapter: ISA adapter Vcore: +1.00 V (min = +0.60 V, max = +1.49 V) in1: +1.87 V (min = +1.62 V, max = +1.99 V) AVCC: +3.28 V (min = +2.98 V, max = +3.63 V) +3.3V: +3.28 V (min = +2.98 V, max = +3.63 V) in4: +1.53 V (min = +1.35 V, max = +1.65 V) in5: +1.27 V (min = +1.13 V, max = +1.38 V) in6: +1.46 V (min = +1.42 V, max = +1.52 V) 3VSB: +3.34 V (min = +2.98 V, max = +3.63 V) Vbat: +3.17 V (min = +2.70 V, max = +3.63 V) fan1: 0 RPM (min = 300 RPM) ALARM fan2: 0 RPM (min = 300 RPM) ALARM fan3: 0 RPM (min = 300 RPM) ALARM fan4: 0 RPM (min = 300 RPM) ALARM fan5: 2042 RPM (min = 300 RPM) SYSTIN: +26.0 C (high = +75.0 C, hyst = +70.0 C) sensor = thermistor CPUTIN: +19.5 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor AUXTIN: +1.0 C (high = +80.0 C, hyst = +75.0 C) sensor = thermistor PECI Agent 0: +29.5 C (high = +95.0 C, hyst = +92.0 C) (crit = +100.0 C) PCH_CHIP_TEMP: +0.0 C PCH_CPU_TEMP: +0.0 C PCH_MCH_TEMP: +0.0 C intrusion0: ALARM intrusion1: OK beep_enable: enabled sensors.conf # lines starting with "#" are comments and ignored # sensor configuration chip "nct6776-isa-0a30" label SYSTIN "MB Temp" label CPUTIN "CPU Temp" can not get the labels for SYSTIN and CPUTIN to change so we page picks it up Thanks for any info Myk Quote Link to comment
umax Posted November 2, 2014 Share Posted November 2, 2014 glad it's working. I assume the temps look correct to you. Some people have to switch the labels around in sensors.conf so cpu is actually the cpu, etc. I didn't have to do that for mine. What is really awesome is the announcement that Dynamix will now be included with V6! That is so cool - this completes unraid IMO. yea, the labels are switched, not a biggie, but can't figure it out... tried 3 different sensors_conf; chip "w83627dhg-isa-0a10" label temp2 "CPU Temp" label temp1 "MB Temp" and chip "w83627dhg-isa-0a10" label temp1 "MB Temp" label temp2 "CPU Temp" and label temp1 "CPU Temp" label temp2 "MB Temp" And yes, that is awesome news indeed, cant wait for V6 final! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.