January 9, 201412 yr My system is at 4.7 I have a disk showing as DISK_DSBL, I tried carrying out the advice of... stopping the array unassign drive start the array with it un-assigned stop the array re-assign the drive that was disabled start the array This then started rebuilding the drive but I came back and its showing DISK_DSBL again, this must have been before it finished rebuilding as it was only a few hours later. system log attached. I ran smart report for the drive but this doesnt fail? smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD20EZRX-00DC0B0 Serial Number: WD-WMC1T2235192 Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Jan 9 23:18:35 2014 Local time zone must be set--see zic m SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26580) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 62 3 Spin_Up_Time 0x0027 182 159 021 Pre-fail Always - 5900 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1211 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 7101 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 30 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 21 193 Load_Cycle_Count 0x0032 196 196 000 Old_age Always - 13537 194 Temperature_Celsius 0x0022 122 103 000 Old_age Always - 28 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 198 198 000 Old_age Always - 854 198 Offline_Uncorrectable 0x0030 200 199 000 Old_age Offline - 121 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 194 186 000 Old_age Offline - 1934 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7101 - # 2 Short offline Completed without error 00% 7095 - # 3 Short offline Completed without error 00% 6321 - # 4 Extended offline Aborted by host 90% 6321 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. The drive is connected to a AOC-SASLP-MV8 controller, I have tried changing the cable already, any advice please? syslog-2014-01-09.zip
January 9, 201412 yr 197 Current_Pending_Sector 0x0032 198 198 000 Old_age Always - 854 198 Offline_Uncorrectable 0x0030 200 199 000 Old_age Offline - 121 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 194 186 000 Old_age Offline - 1934 Your drive has 854 current pending sectors. Your drive is bad and it's time to get a new one.
January 10, 201412 yr Author Drive is still in warranty so nice, free replacement! Thanks for your help.
January 10, 201412 yr If you RMA your drive, WD has the tendency to replace it with a larger capacity drive. If they do you will have to update your server to version 5.0. Just keep that on mind
January 10, 201412 yr Author I have RMA and it looks like they are sending the same size, I have been meaning to upgrade to v5 to start incorporating bigger disks but need to get the array stable and working before going for it.
Archived
This topic is now archived and is closed to further replies.