Silverstone DS380 thread?


tucansam

Recommended Posts

On 6/19/2020 at 2:40 PM, Big Dan T said:

Hi,

 

Just curious has anyone managed to get a 1650 Super graphics card inside the DS380 without having to sacrifice a drive bay ??

 

I'm doing a new Ryzen build with this case and am looking at getting a MSI GeForce GTX 1650 SUPER AERO ITX OC 4GB Graphics Card for Transcoding, but want to triple check it will fit without loosing a bay ?

 

Cheers

 

Dan

While I've never tried this I have had my frustrations with the case. (To the point I gave up and switched to a 381 which has its own frustrations.)  Can I ask what build you're planning that you can fit a Ryzen itx board and 8 hard drives? I always came up with the answer of "there isn't enough slots!"

Link to comment
57 minutes ago, pras1011 said:

Small itx build with power supply internally. 6 x 16tb hdd. Horsham is good. I want something as small as the ds380 but smaller.

I don't know how it compares specifically to the DS380, but the Fractal Node 304 is a very compact 6 drive case.  I am using it with my backup server.  Some have even installed with Velcro a couple of SSDs outside the disk hangers for a total of 8 drives.

 

Unfortunately, the Lian-Li PC-Q25 is no longer available or I would highly recommend that case.  I am hanging onto the one I have for a future build.

Link to comment

The DS380 is 21.6 litres.  The Fractal Node 304 is 19.2 litres, so, 2.4 litres smaller. 

 

I don't know that you will find a 6 HDD Mini-ITX case as small as 13 litres.

 

U-NAS makes some small cases but it appears they have only 4-bay and 8-bay models.

Edited by Hoopster
Link to comment
On 7/13/2020 at 3:22 PM, Tai said:

While I've never tried this I have had my frustrations with the case. (To the point I gave up and switched to a 381 which has its own frustrations.)  Can I ask what build you're planning that you can fit a Ryzen itx board and 8 hard drives? I always came up with the answer of "there isn't enough slots!"

Got it to work in the end. Got a Palit 1650 which fits in the case without the need to loose a drive bay.

 

So with this setup I’ve got 8 hot swappable bays plus 1 m.2 SSD and a second 2.5 SSD.

 

based on a ryzen 3600.

 

took me ages to build :)

D032826F-FC85-42F4-8C6C-39BBF7366633.jpeg

61D91C8A-92F6-4323-A1A8-3C84F31B3439.jpeg

5D3200A0-ABBD-4591-9E53-EE3B95CB62D7.jpeg

Link to comment

Ok, so a little update from a first time unraider.

 

got two (14tb) drives that I’m preclearing at the mo and will get into the server when they are ready. They are wd element drives. Which are currently running very hot during preclear (around 50c). Had to get a fan on them to bring them back down to a more acceptable 34c.

95B53553-797B-4F91-A859-E2F9EFFEBCE6.thumb.jpeg.38cba51ef7b57f3d455a6261d2195f94.jpeg
 

I also forgot to mention I 3D printed two skirts to sort out the airflow issue as seen below. A word of warning these skirts need to be filled / cut down a bit to work with Noctua fans as they are slightly too high for the Ds380 drive cage. But otherwise good to go.

 

14801BBC-146D-4530-A5DA-C2B6F405D2E8.thumb.jpeg.b7e43978331cab328568b8101d3b9db6.jpeg


97C5C76C-72D3-46E1-8147-D9F8DB6EA7AE.thumb.jpeg.15f347091a2fd9d0f145354213a16a1b.jpeg


 

I don’t have a 3D printer myself so had to use an online service to print them (£25) for 3 but you only need 2. You can find the design files on google.

 

my only other gripe so far is that with Unraid version 6.8.3 you can’t see the cpu or fan temps on ryzen CPU or boards. Apparently this is fixed in version 6.9 but I’m going to wait for a stable release before upgrading (I’m a nervous neW unraider).

 

ill let you know the temps of my new drives once they are through preclear (about a week) and on the server

Edited by Big Dan T
Link to comment

oh and the inspiration for my build came from this video:- 

 

 

 

Except i didn't go quite so high end  on the specs as 1) I couldn't afford it 2) it should run a bit less hot with some of my specs (Hopefully)

 

Also i didn't want to sacrifice a drive bay as shown in the video, so with a very small 1650 you keep all your drive bays usable.

Edited by Big Dan T
Link to comment
  • 1 year later...
On 7/21/2020 at 3:15 PM, Big Dan T said:

Ok, so a little update from a first time unraider.

 

got two (14tb) drives that I’m preclearing at the mo and will get into the server when they are ready. They are wd element drives. Which are currently running very hot during preclear (around 50c). Had to get a fan on them to bring them back down to a more acceptable 34c.

95B53553-797B-4F91-A859-E2F9EFFEBCE6.thumb.jpeg.38cba51ef7b57f3d455a6261d2195f94.jpeg
 

I also forgot to mention I 3D printed two skirts to sort out the airflow issue as seen below. A word of warning these skirts need to be filled / cut down a bit to work with Noctua fans as they are slightly too high for the Ds380 drive cage. But otherwise good to go.

 

14801BBC-146D-4530-A5DA-C2B6F405D2E8.thumb.jpeg.b7e43978331cab328568b8101d3b9db6.jpeg


97C5C76C-72D3-46E1-8147-D9F8DB6EA7AE.thumb.jpeg.15f347091a2fd9d0f145354213a16a1b.jpeg


 

I don’t have a 3D printer myself so had to use an online service to print them (£25) for 3 but you only need 2. You can find the design files on google.

 

my only other gripe so far is that with Unraid version 6.8.3 you can’t see the cpu or fan temps on ryzen CPU or boards. Apparently this is fixed in version 6.9 but I’m going to wait for a stable release before upgrading (I’m a nervous neW unraider).

 

ill let you know the temps of my new drives once they are through preclear (about a week) and on the server

 

Have the ducts lowered your HDD temps? And would you mind telling me which online service you used to buy  them please?

Link to comment
  • 1 month later...
On 5/20/2022 at 11:16 PM, unraid20 said:

 

Have the ducts lowered your HDD temps? And would you mind telling me which online service you used to buy  them please?

Well I've always used them, so I couldn't tell you how much they lowered by temps by. 

 

I cant find the guys i used but I think it was here:- https://3dprintdirect.co.uk/quote/

 

And it cost something like £25-30 ? which is a bit steep for a bit of plastic, but worth it for peace of mind.

 

An FYI, i had to shave a bit off the ducts to get them to fit, not alot, but a bit.

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.