March 8, 201412 yr Running Unraid 5rc3 plugins are (sab,SB,CP and cached directories) Asus MB with A6-3500 APU and 4g of ram 10 Drives(29tb), 550w psu Recently upgraded to a 4 port STATA card (si-pex40064 Marvell 88SE9215) I immediately noticed errors in syslog, and I believe its my cache drive which isn't hooked up to the new card. Attached are the syslog and the smart report on the drive. I'm running the extended smart test, but it wont complete for 48 mins.. I've also had a few random reboots in the last few days, since installing the new card. Could someone help me decipher the syslog? Cable, approaching PSU limit, or physical drive issues? Thanks! SMART status Info for /dev/sdd smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD2500AAKX-321CA0 Serial Number: WD-WCAYUDU72589 Firmware Version: 15.01H15 User Capacity: 250,059,350,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sat Mar 8 08:09:50 2014 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (4500) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 164 108 051 Pre-fail Always - 420 3 Spin_Up_Time 0x0027 192 173 021 Pre-fail Always - 1375 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 141 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 17 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 139 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 135 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 5 194 Temperature_Celsius 0x0022 118 113 000 Old_age Always - 25 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 5 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 5 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 5 SMART Error Log Version: 1 ATA Error Count: 378 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 378 occurred at disk power-on lifetime: 5 hours (0 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 24 01 28 e3 Error: UNC 8 sectors at LBA = 0x03280124 = 52953380 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 20 01 28 e3 08 01:31:49.733 READ DMA ef 10 02 00 00 00 a0 08 01:31:49.733 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 01:31:49.732 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 01:31:49.732 SET FEATURES [set transfer mode] Error 377 occurred at disk power-on lifetime: 5 hours (0 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 24 01 28 e3 Error: UNC 8 sectors at LBA = 0x03280124 = 52953380 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 20 01 28 e3 08 01:31:47.969 READ DMA ef 10 02 00 00 00 a0 08 01:31:47.969 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 01:31:47.968 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 01:31:47.968 SET FEATURES [set transfer mode] Error 376 occurred at disk power-on lifetime: 5 hours (0 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 24 01 28 e3 Error: UNC 8 sectors at LBA = 0x03280124 = 52953380 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 20 01 28 e3 08 01:31:46.204 READ DMA ef 10 02 00 00 00 a0 08 01:31:46.204 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 01:31:46.203 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 01:31:46.203 SET FEATURES [set transfer mode] Error 375 occurred at disk power-on lifetime: 5 hours (0 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 24 01 28 e3 Error: UNC 8 sectors at LBA = 0x03280124 = 52953380 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 20 01 28 e3 08 01:31:44.439 READ DMA ef 10 02 00 00 00 a0 08 01:31:44.439 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 01:31:44.438 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 01:31:44.438 SET FEATURES [set transfer mode] Error 374 occurred at disk power-on lifetime: 5 hours (0 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 24 01 28 e3 Error: UNC 8 sectors at LBA = 0x03280124 = 52953380 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 20 01 28 e3 08 01:31:42.674 READ DMA ef 10 02 00 00 00 a0 08 01:31:42.674 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 08 01:31:42.673 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 01:31:42.673 SET FEATURES [set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 17 52953380 # 2 Short offline Completed: read failure 90% 16 52953380 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. syslog-2014-03-08.zip
March 8, 201412 yr See here: http://lime-technology.com/wiki/index.php/Troubleshooting#Resolving_a_Pending_Sector After that, see Check Disk Filesystems in my sig,
Archived
This topic is now archived and is closed to further replies.