uhhuh Posted October 27, 2014 Share Posted October 27, 2014 I ran 3 preclear cycles with the Seagate 6tb attached to the Motherboard and it displays the temp as "0)". Had 2 WD 4TB Reds preclearing also, and they did display a temp. I now have it hooked it up to my new sata controller, and it does not display a temp. There are no jumpers attached to it. Suggestions for my next step? Drive - Seagate Desktop HDD 6TB 6Gb/s 128MB Cache 3.5-Inch Internal Drive Retail Kit (STBD6000100) (http://www.amazon.com/Seagate-Desktop-3-5-Inch-Internal-STBD6000100/dp/B00JBJ34WC/ref=sr_1_1?ie=UTF8&qid=1414374227&sr=8-1&keywords=Seagate+Desktop+HDD+6TB+6Gb%2Fs+128MB+Cache+3.5-Inch+Internal+Drive+Retail+Kit+%28STBD6000100%29) New Sata Controller - SUPERMICRO AOC-SAS2LP-MV8 PCI-Express 2.0 x8 SATA / SAS 8-Port Controller Card (http://www.newegg.com/Product/Product.aspx?Item=N82E16816101792) Info about the drive: /dev/sdc: ATA device, with non-removable media Model Number: ST6000DX000-1H217Z Serial Number: Z4D06290 Firmware Revision: CC47 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SAT A Rev 2.5, SATA Rev 2.6, SATA Rev 3.0 Standards: Used: unknown (minor revision code 0x001f) Supported: 10 9 8 7 6 5 Likely used: 10 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors:11721045168 Logical Sector size: 512 bytes Physical Sector size: 4096 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 5723166 MBytes device size with M = 1000*1000: 6001175 MBytes (6001 GB) cache/buffer size = unknown Form Factor: 3.5 inch Nominal Media Rotation Rate: 7200 Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = ? Advanced power management level: 128 Recommended acoustic management value: 208, current value: 208 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension * 48-bit Address feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name * IDLE_IMMEDIATE with UNLOAD Write-Read-Verify feature set * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE unknown 119[6] unknown 119[8] * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Native Command Queueing (NCQ) * Phy event counters * Idle-Unload when NCQ is active * unknown 76[15] DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation unknown 78[7] * SMART Command Transport (SCT) feature set * SCT Write Same (AC2) unknown 206[7] unknown 206[12] (vendor specific) * reserved 69[3] Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase Logical Unit WWN Device Identifier: 5000c500676a28df NAA : 5 IEEE OUI : 000c50 Unique ID : 0676a28df Checksum: correct Edit: Added SS of drive Quote Link to comment
uhhuh Posted October 30, 2014 Author Share Posted October 30, 2014 So an update. I opened up UnMenu and the temp is displaying. I guess this is a problem with the Dynamix GUI. I will post in the plugin thread now. Edit*** I had this issue with 2 6tb disks. HGST & Seagate. I added the HGST to the array, and it started displaying the temp correctly. Parity has been built and is being checked. Everything looks good now. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.