Billy_McSkintos Posted November 7, 2014 Share Posted November 7, 2014 I began running UnRaid 5.05 earlier this year and have been nothing but delighted but I recently upgrade from 5.05 to 5.06 with a small hardware refresh in between (new power supply, replaced RMA's MoBo). I now have a single drive that will not remain spun down and is running hot. I am a bit of an amateur and lost as to my next steps. I am hoping this wonderful forum can help me out? Thank you! EDIT: Apologies to all, I'm an idiot. I installed BTSync and the share was mounted on the spinning disk. I moved it to my cache SSD and all is well. Billy_McSkintos Smart.txt: smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723030ALA640 Serial Number: MK0333YHGBK2MC LU WWN Device Id: 5 000cca 225c54037 Firmware Version: MKAOA5C0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Nov 6 18:05:09 2014 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (30457) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 508) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 133 133 054 Pre-fail Offline - 91 3 Spin_Up_Time 0x0007 137 137 024 Pre-fail Always - 620 (Average 506) 4 Start_Stop_Count 0x0012 099 099 000 Old_age Always - 4859 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 138 138 020 Pre-fail Offline - 25 9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 27616 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 146 192 Power-Off_Retract_Count 0x0032 096 096 000 Old_age Always - 4863 193 Load_Cycle_Count 0x0012 096 096 000 Old_age Always - 4863 194 Temperature_Celsius 0x0002 146 146 000 Old_age Always - 41 (Min/Max 20/79) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 27607 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. syslog.zip smart.txt Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.