February 15, 201511 yr Hi All, I have a quick question - looking at the smart report this drive is throwing a couple of errors and Im not sure when to pull the plug. this is just my cache drive so little data is at risk - unless when the mover takes data to my array. Can you please have a look at this smart report and give my your opinion - what to watch for as time goes on or when is it time to literally throw this in the trash? thanks! smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build) Copyright © 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.C Device Model: Hitachi HDS721010CLA332 Serial Number: JP2930HQ1N9AVH LU WWN Device Id: 5 000cca 35dd75206 Firmware Version: JP4OA39C User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Feb 15 12:03:06 2015 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9812) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 164) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 099 099 016 Pre-fail Always - 65537 2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 93 3 Spin_Up_Time 0x0007 116 116 024 Pre-fail Always - 325 (Average 325) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1652 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 1 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 130 130 020 Pre-fail Offline - 35 9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 30960 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 509 192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1720 193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1720 194 Temperature_Celsius 0x0002 240 240 000 Old_age Always - 25 (Min/Max 11/42) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
February 15, 201511 yr There is one reallocated sector out of 30,000 hours. Other then that nothing jumps out (to me) yet. I would suggest running a long test. The smart long test may reveal more.
February 23, 201511 yr Author Thank you WeeboTech. I ran the long test, but I have no idea what the output is - is there a report somewhere? thanks, kf
February 23, 201511 yr Thank you WeeboTech. I ran the long test, but I have no idea what the output is - is there a report somewhere? thanks, kf Repost the smartlog here and we'll look at it.
February 23, 201511 yr Author That's just it, i don't know where the smartlog is. I ran the test from the web interface and it simply said the test is complete- no report. Maybe I didnt do this correctly?
February 23, 201511 yr do the same thing you did to attach the first one. login via console and do smartctl -a /dev/sd? where ? is drive letter. or for unRAID 6 via interface. go to Main click on the disk in question. go to Health Tab look at disk Attributes, disk self-test log and disk error log.
Archived
This topic is now archived and is closed to further replies.