dmacias Posted March 28, 2016 Author Share Posted March 28, 2016 Given your fan rpms I'd say they aren't pwm fans or controllable by your motherboard and are running at full speed. My board can only control pwm fans. It would run the 3pin case fans at full speed. I bought a few noctua pwm f-12s or p-12s Quote Link to comment
dbknightx Posted March 28, 2016 Share Posted March 28, 2016 I think they are pwm fans. This is my case and it lists all fans as pwm: https://www.supermicro.com/products/chassis/3U/933/SC933T-R760.cfm I'll need to do some more digging and see if only certain fan headers on the motherboard support fan control. There are a bunch of them so I may just try moving them around and see if anything changes. Thanks for the help. Quote Link to comment
dbknightx Posted March 29, 2016 Share Posted March 29, 2016 So I opened up my server last night and you are right - the fans are all 3-pin and not pwm fans. I'm planning on upgrading all of them and will do more testing once that has happened. Thanks for the guidance and am really looking forward to the forthcoming fan control feature. Six 5000 RPM fans running at full speed is EXTREMELY loud! Quote Link to comment
dmacias Posted March 29, 2016 Author Share Posted March 29, 2016 So I opened up my server last night and you are right - the fans are all 3-pin and not pwm fans. I'm planning on upgrading all of them and will do more testing once that has happened. Thanks for the guidance and am really looking forward to the forthcoming fan control feature. Six 5000 RPM fans running at full speed is EXTREMELY loud! I bet that's loud. Mine only go up to 1500, l believe. I took a look at your case and it does say right on the page 5000 rpm pwm fans. I also looked at your motherboard manual and it says all fans default to Full On. But the manual didn't say what other values there are other than Full On. And didn't show any smart fan settings. Also you can check just the fans after you try the raw command like this ipmi-raw 00 3a 01 00 00 32 00 00 00 00 00 ipmi-sensors -t fan Quote Link to comment
dmacias Posted March 29, 2016 Author Share Posted March 29, 2016 So I opened up my server last night and you are right - the fans are all 3-pin and not pwm fans. I'm planning on upgrading all of them and will do more testing once that has happened. Thanks for the guidance and am really looking forward to the forthcoming fan control feature. Six 5000 RPM fans running at full speed is EXTREMELY loud! Could you tell me what the output of "ipmi-sensors -t fan". Since you have more fans connections than I do, I'd like to know the name of the other 2 fans since the ipmi-raw command has 8 values. Here's mine. root@server:~# ipmi-sensors -t fan ID | Name | Type | Reading | Units | Event 13 | CPU_FAN1 | Fan | 1100.00 | RPM | 'OK' 14 | REAR_FAN1 | Fan | 800.00 | RPM | 'OK' 15 | FRNT_FAN1 | Fan | N/A | RPM | N/A 16 | FRNT_FAN2 | Fan | 800.00 | RPM | 'OK' 17 | REAR_FAN2 | Fan | N/A | RPM | N/A 18 | CPU_FAN2 | Fan | N/A | RPM | N/A root@server:~# Quote Link to comment
dbknightx Posted March 30, 2016 Share Posted March 30, 2016 Could you tell me what the output of "ipmi-sensors -t fan". Since you have more fans connections than I do, I'd like to know the name of the other 2 fans since the ipmi-raw command has 8 values. Here's mine. Sure. Here you go: root@Tower:~# ipmi-sensors -t fan ID | Name | Type | Reading | Units | Event 17 | CPU_FAN1_1 | Fan | N/A | RPM | N/A 18 | CPU_FAN2_1 | Fan | N/A | RPM | N/A 19 | REAR_FAN1 | Fan | 0.00 | RPM | 'At or Below (<=) Lower Non-Critical Threshold' 20 | REAR_FAN2 | Fan | 0.00 | RPM | 'At or Below (<=) Lower Non-Critical Threshold' 21 | FRNT_FAN1 | Fan | N/A | RPM | N/A 22 | FRNT_FAN2 | Fan | N/A | RPM | N/A 23 | FRNT_FAN3 | Fan | N/A | RPM | N/A 24 | FRNT_FAN4 | Fan | 2900.00 | RPM | 'OK' 25 | CPU_FAN1_2 | Fan | N/A | RPM | N/A 26 | CPU_FAN2_2 | Fan | N/A | RPM | N/A Three of my front four fans are still connected to the drive array backplane power (not the motherboard) which is why only FRNT_FAN4 is reporting readings. Not sure why the two REAR_FANs are showing zero, since they are definitely running. Hope this helps. Quote Link to comment
dmacias Posted March 30, 2016 Author Share Posted March 30, 2016 Thanks. Since CPU_FAN1_2 and CPU_FAN2_2 are 3pin and are last in ipmi-sensors list that's good. I already cut the fan page down to 8 possible fans since there's only 8 values. So that works out since they aren't controllable. When you get some 4pin pwm fans you'll have to do some testing and see if the fans and values below are a match. ipmi-raw 00 3a 01 00 00 00 00 00 00 00 00 ipmi-raw 00 3a 01 AA BB CC DD EE FF GG HH 00 = smartfan mode 01 - 0x64 = 1% - 100% 'CPU_FAN1_1' => 'AA', 'CPU_FAN2_1' => 'BB', 'REAR_FAN1' => 'CC', 'REAR_FAN2' => 'DD', 'FRNT_FAN1' => 'EE', 'FRNT_FAN2' => 'FF', 'FRNT_FAN3' => 'GG', 'FRNT_FAN4' => 'HH' Quote Link to comment
ljm42 Posted April 8, 2016 Share Posted April 8, 2016 Hi dmacias, I followed CHBMB's instructions: https://www.linuxserver.io/index.php/2015/12/14/creating-an-unraid-virtual-machine-to-run-on-an-unraid-host/ to install 6.2 b21 as a guest in 6.1.9. There were a few extra difficulties I talked about here: https://lime-technology.com/forum/index.php?topic=36768.msg462285#msg462285 but it works great for testing plugins and such. So I installed the IPMI plugin in the guest VM, thinking it would be able to access the IPMI system over the network and display temperature info. But the system slowed to a crawl and started dumping these messages in the syslog: Apr 7 18:02:31 TowerVM kernel: x86/PAT: ipmi-fru:3178 map pfn expected mapping type uncached-minus for [mem 0x7ffe2000-0x7ffe2fff], got write-back Apr 7 18:03:39 TowerVM kernel: x86/PAT: ipmi-sensors:3400 map pfn expected mapping type uncached-minus for [mem 0x7ffe2000-0x7ffe2fff], got write-back And these on the console: modprobe: ERROR: could not insert 'ipmi_si' : No such device Caching SDR repository information: /root/.freeipmi/sdr-cache/sdr-cache-TowerVM. ipmi_sdr_cache_create: internal IPMI error I had to uninstall it from the VM's console to revive the UI: plugin remove ipmi.plg Do you know if it would be possible to get the plugin to work in a VM? This isn't critical or anything, but it would be cool Quote Link to comment
dmacias Posted April 8, 2016 Author Share Posted April 8, 2016 I will work fine in a vm. I already had a fix in place. I just had added another condition but didn't enclose in braces. I updated the plugin. Unlike ipmitool, freeipmi doesn't have a variable for local timeout. I think its set to 20 seconds. That's the reason the webgui becomes slow. Edit: I also setup a couple VM's for testing. My board doesn't support vx-d and only one usb controller so I can't passthrough a usb. And if I forget and leave the usb in, then a reboot will cause problems. So I just left the VM image named UNRAID and boot directly from the image using the usb option for hard drive in 6.2 vm manager. I can't start the array in the vm but I can test things and compile packages. Quote Link to comment
ljm42 Posted April 8, 2016 Share Posted April 8, 2016 OK, thanks! Since it works for you, I pushed through the delays until I could enable the IPMI network connection and set the ip address, username and password. Once the connection was successful the GUI sped back up. However, I'm seeing these two lines added to the syslog every 10 seconds, any idea how to stop that? Apr 7 21:40:10 TowerVM kernel: IPMI System Interface driver. Apr 7 21:40:10 TowerVM kernel: ipmi_si: Unable to find any System Interface(s) Apr 7 21:40:20 TowerVM kernel: IPMI System Interface driver. Apr 7 21:40:20 TowerVM kernel: ipmi_si: Unable to find any System Interface(s) Apr 7 21:40:31 TowerVM kernel: IPMI System Interface driver. Apr 7 21:40:31 TowerVM kernel: ipmi_si: Unable to find any System Interface(s) Apr 7 21:40:41 TowerVM kernel: IPMI System Interface driver. Apr 7 21:40:41 TowerVM kernel: ipmi_si: Unable to find any System Interface(s) Also, even though I was able to select which temp/fan sensors to display, there are no temp/fan speeds shown in the footer. Have I forgotten a setting somewhere? The readings *do* show up on the Tools -> IPMI page, so it is able to get the data. Here's my ipmi.cfg if it helps: SERVICE="disable" IPMIPOLL="15" NETWORK="enable" LOCAL="disable" IPADDR="192.168.10.50" USER="admin" PASSWORD="***" IPMISELD="disable" DISP_TEMP1="3232238130_27" DISP_TEMP2="3232238130_30" DISP_FAN1="3232238130_21" DISP_FAN2="3232238130_19" IPMIFAN="disable" IPMIBOARD="" Actually, I went ahead and attached my diagnostics in case you want to poke around. towervm-diagnostics-20160407-2156.zip Quote Link to comment
dmacias Posted April 8, 2016 Author Share Posted April 8, 2016 I updated the plugin last night. That will get rid of the delays. I get the same in the log and no footer though. The footer worked before so I'll figure out what I broke. The log is a result of it checking for local ipmi by getting a result from modprobe. I'll try to suppress that or figure out a different way to check. Quote Link to comment
ljm42 Posted April 8, 2016 Share Posted April 8, 2016 Cool, at least we are seeing the same things Do we have the option of not loading "modprobe ipmi_si" for network installs? Quote Link to comment
dmacias Posted April 8, 2016 Author Share Posted April 8, 2016 Cool, at least we are seeing the same things Do we have the option of not loading "modprobe ipmi_si" for network installs? Yes that what I did to fix it. Not check for ipmi if network is enabled. The footer not working was because I changed the separator for the long ip and sensor id to an underscore instead of a dash and forgot one area of code. I'll update later today maybe with much more. Quote Link to comment
ljm42 Posted April 8, 2016 Share Posted April 8, 2016 That sounds great! If you're looking for ideas I'd really like to see plugins take advantage of this new functionality that was added to 6.2b21: - API for plugins to test and display a new version message bonienl explained it here: https://lime-technology.com/forum/index.php?topic=47944.msg459607#msg459607 Quote Link to comment
dmacias Posted April 8, 2016 Author Share Posted April 8, 2016 That sounds great! If you're looking for ideas I'd really like to see plugins take advantage of this new functionality that was added to 6.2b21: - API for plugins to test and display a new version message bonienl explained it here: https://lime-technology.com/forum/index.php?topic=47944.msg459607#msg459607 Thanks. I hadn't seen that. Quote Link to comment
cyriouslydylan Posted April 14, 2016 Share Posted April 14, 2016 I'm trying to get this to work on my Supermicro X11SSM-F and I don't seem to be having any luck. Could anyone point me in the right direction? Quote Link to comment
dmacias Posted April 14, 2016 Author Share Posted April 14, 2016 I'm trying to get this to work on my Supermicro X11SSM-F and I don't seem to be having any luck. Could anyone point me in the right direction? Try ipmi-sensors from the command line. What does it show? Quote Link to comment
cyriouslydylan Posted April 14, 2016 Share Posted April 14, 2016 I'm trying to get this to work on my Supermicro X11SSM-F and I don't seem to be having any luck. Could anyone point me in the right direction? Try ipmi-sensors from the command line. What does it show? "-bash: ipmi-sensors: command not found" I didn't have the ipmi plugin installed, but when I do install it I get this message repeating constantly: "-u: ipmi-fru: invalid hostname" Apologies, I'm dumb. I just got the command to work: ID | Name | Type | Reading | Units | Event 4 | CPU Temp | Temperature | 28.00 | C | 'OK' 71 | PCH Temp | Temperature | 34.00 | C | 'OK' 138 | System Temp | Temperature | 27.00 | C | 'OK' 205 | Peripheral Temp | Temperature | 31.00 | C | 'OK' 272 | VcpuVRM Temp | Temperature | 31.00 | C | 'OK' 339 | DIMMA1 Temp | Temperature | 27.00 | C | 'OK' 406 | DIMMA2 Temp | Temperature | N/A | C | N/A 473 | DIMMB1 Temp | Temperature | 28.00 | C | 'OK' 540 | DIMMB2 Temp | Temperature | N/A | C | N/A 607 | FAN1 | Fan | 900.00 | RPM | 'OK' 674 | FAN2 | Fan | 800.00 | RPM | 'OK' 741 | FAN3 | Fan | N/A | RPM | N/A 808 | FAN4 | Fan | 800.00 | RPM | 'OK' 875 | FANA | Fan | N/A | RPM | N/A 942 | 12V | Voltage | 12.13 | V | 'OK' 1009 | 5VCC | Voltage | 4.95 | V | 'OK' 1076 | 3.3VCC | Voltage | 3.38 | V | 'OK' 1143 | VBAT | Voltage | 3.08 | V | 'OK' 1210 | VCPU | Voltage | 0.86 | V | 'OK' 1277 | VDIMMAB | Voltage | 1.19 | V | 'OK' 1344 | 5VSB | Voltage | 5.00 | V | 'OK' 1411 | 3.3VSB | Voltage | 3.21 | V | 'OK' 1478 | VBMC 1.2V | Voltage | 1.20 | V | 'OK' 1545 | VPCH 1.0V | Voltage | 1.00 | V | 'OK' 1612 | Chassis Intru | Physical Security | N/A | N/A | 'OK' Quote Link to comment
dmacias Posted April 14, 2016 Author Share Posted April 14, 2016 I'm trying to get this to work on my Supermicro X11SSM-F and I don't seem to be having any luck. Could anyone point me in the right direction? Try ipmi-sensors from the command line. What does it show? "-bash: ipmi-sensors: command not found" I didn't have the ipmi plugin installed, but when I do install it I get this message repeating constantly: "-u: ipmi-fru: invalid hostname" Did the plugin show any errors when you installed it? Also what version of unRAID? Here's the link https://raw.githubusercontent.com/dmacias72/unRAID-plugins/master/plugins/ipmi.plg Quote Link to comment
dmacias Posted April 14, 2016 Author Share Posted April 14, 2016 I'm trying to get this to work on my Supermicro X11SSM-F and I don't seem to be having any luck. Could anyone point me in the right direction? Try ipmi-sensors from the command line. What does it show? "-bash: ipmi-sensors: command not found" I didn't have the ipmi plugin installed, but when I do install it I get this message repeating constantly: "-u: ipmi-fru: invalid hostname" Did you set up networking? You only need that for remote ipmi monitoring e.g. another machine on the network. Quote Link to comment
cyriouslydylan Posted April 14, 2016 Share Posted April 14, 2016 I'm trying to get this to work on my Supermicro X11SSM-F and I don't seem to be having any luck. Could anyone point me in the right direction? Try ipmi-sensors from the command line. What does it show? "-bash: ipmi-sensors: command not found" I didn't have the ipmi plugin installed, but when I do install it I get this message repeating constantly: "-u: ipmi-fru: invalid hostname" Did the plugin show any errors when you installed it? Also what version of unRAID? Here's the link https://raw.githubusercontent.com/dmacias72/unRAID-plugins/master/plugins/ipmi.plg I reinstalled it and was able to get it to work, ipmi-sensors returns this: ID | Name | Type | Reading | Units | Event 4 | CPU Temp | Temperature | 28.00 | C | 'OK' 71 | PCH Temp | Temperature | 34.00 | C | 'OK' 138 | System Temp | Temperature | 27.00 | C | 'OK' 205 | Peripheral Temp | Temperature | 31.00 | C | 'OK' 272 | VcpuVRM Temp | Temperature | 31.00 | C | 'OK' 339 | DIMMA1 Temp | Temperature | 27.00 | C | 'OK' 406 | DIMMA2 Temp | Temperature | N/A | C | N/A 473 | DIMMB1 Temp | Temperature | 28.00 | C | 'OK' 540 | DIMMB2 Temp | Temperature | N/A | C | N/A 607 | FAN1 | Fan | 900.00 | RPM | 'OK' 674 | FAN2 | Fan | 800.00 | RPM | 'OK' 741 | FAN3 | Fan | N/A | RPM | N/A 808 | FAN4 | Fan | 800.00 | RPM | 'OK' 875 | FANA | Fan | N/A | RPM | N/A 942 | 12V | Voltage | 12.13 | V | 'OK' 1009 | 5VCC | Voltage | 4.95 | V | 'OK' 1076 | 3.3VCC | Voltage | 3.38 | V | 'OK' 1143 | VBAT | Voltage | 3.08 | V | 'OK' 1210 | VCPU | Voltage | 0.86 | V | 'OK' 1277 | VDIMMAB | Voltage | 1.19 | V | 'OK' 1344 | 5VSB | Voltage | 5.00 | V | 'OK' 1411 | 3.3VSB | Voltage | 3.21 | V | 'OK' 1478 | VBMC 1.2V | Voltage | 1.20 | V | 'OK' 1545 | VPCH 1.0V | Voltage | 1.00 | V | 'OK' 1612 | Chassis Intru | Physical Security | N/A | N/A | 'OK' Quote Link to comment
dmacias Posted April 14, 2016 Author Share Posted April 14, 2016 Everything works in the unRAID webgui? Quote Link to comment
cyriouslydylan Posted April 14, 2016 Share Posted April 14, 2016 Everything works in the unRAID webgui? Yes I can see all these sensors now if I go to tools > IPMI. My event log is filled with "Lower Critical - going low ; Sensor Reading = 500.00 RPM ; Threshold = 500.00 RPM" warnings and errors. And in the IPMI settings, fan control has a big red "NOT FUNCTIONAL YET" next to "IPMI Fan Control" As far as the rest of the unRAID webgui is concerned, yes everything seems to be going fine. It looks like my FAN4 is the one constantly cycling. Quote Link to comment
dmacias Posted April 14, 2016 Author Share Posted April 14, 2016 I'm currently testing the fan control but it will only work with ASRock boards. I have compiled a list of some Supermicro commands I will post if others want to test. The threshold values for your fan is set too low. That's the reason for the errors. You can use the following commands to output your ipmi config to a file. Edit the file with a linux compatible text editor. Then save and commit the changes. #output ipmi config ipmi-sensors-config --filename=/boot/config/plugins/ipmi/ipmi.config --checkout #save ipmi config ipmi-sensors-config --filename=/boot/config/plugins/ipmi/ipmi.config --commit I'm in the process of adding this to the plugin similar to editing a vm's xml Quote Link to comment
dmacias Posted April 14, 2016 Author Share Posted April 14, 2016 Here's some super micro commands I compiled if anyone wants to test and report back. Fan Speed CLI ATEN X9 ipmi-raw 00 30 91 5A 03 00 00 ipmi-raw 00 30 91 5A 03 01 00 ipmi-raw 00 30 91 5A 03 02 00 ipmi-raw 00 30 91 5A 03 03 00 One is for Write and one is for Read. // for full speed ipmi-raw 00 30 91 5A 03 10 ff ipmi-raw 00 30 91 5A 03 11 ff //for half speed ipmi-raw 00 30 91 5A 03 10 7f ipmi-raw 00 30 91 5A 03 11 7f Set/Get Fan speed mode Input : NetFn 30 Cmd 45 Data1 Get/Set ->[0/1] Data2 Fan Speed Mode, standard/full/optimal -> [0/1/2] // for Set only Output: Completion Code 00 Example: Set fans to full speed would be #ipmi-raw 00 30 45 01 01 if ($max_temp > 39) { # at least one hard drive is 40 deg C or higher # set fan speed control to Full `ipmi-raw 00 30 45 01 01` } elsif ($max_temp == 39 ){ # maximum drive temperature is 39 deg C # set fan speed to 50% duty cycle `ipmi-raw 00 30 70 66 01 00 32` } else { # all hard drive temperatures are 38 deg C or cooler # set fan speed control to Optimal `ipmi-raw 00 30 45 01 02` } 30 70 66 Fan Control Manually (X10) #100% duty cycle ipmi-raw 00 30 70 66 01 00 64 #50% duty cycle ipmi-raw 00 30 70 66 01 00 32 The last value is the duty cycle, with max = 64, and minimum = 0. You can set the duty cycle in 64 steps, between minimum and full speed. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.