jus7incase Posted May 28, 2015 Posted May 28, 2015 Folks, I took a SMART report of all drives. Except for one drive, all other drives have logged no errors. The only drive that has logged errors is the former parity drive. The error seems to be old (at 44 days operation) and I never had parity problems with that drive. Also the feature 184 End-to-End Error reports "FAILING NOW"! I was intending to replace my old 250GB cache drive with this 3TB drive. Could someone please take a look if this drive is ok to use as cache drive? (I understand the cache content is not protected by parity, if not run in a pool, I don't have unRAID 6 yet) Thank you so much! PS: The report was taken while the drive is pre-clearing! Thus the high temp. It is usually cooler. smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST3000DM001-1CH166 Firmware Version: CC26 User Capacity: 3,000,592,982,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Thu May 28 13:05:33 2015 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 55763472 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1969 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 051 047 030 Pre-fail Always - 1383022134666 9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 14866 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 62 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 093 093 099 Old_age Always FAILING_NOW 7 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 096 096 000 Old_age Always - 4 190 Airflow_Temperature_Cel 0x0022 062 055 045 Old_age Always - 38 (Min/Max 30/39) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 11 193 Load_Cycle_Count 0x0032 081 081 000 Old_age Always - 38294 194 Temperature_Celsius 0x0022 038 045 000 Old_age Always - 38 (0 17 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 182291296946429 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 72536194288 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 155726243753 SMART Error Log Version: 1 ATA Error Count: 5 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 occurred at disk power-on lifetime: 1076 hours (44 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 44d+20:48:56.856 READ DMA EXT ef 10 02 00 00 00 a0 00 44d+20:48:56.856 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 44d+20:48:56.856 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 44d+20:48:56.855 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 44d+20:48:56.855 SET FEATURES [set transfer mode] Error 4 occurred at disk power-on lifetime: 1076 hours (44 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 44d+20:48:56.731 READ DMA EXT ef 10 02 00 00 00 a0 00 44d+20:48:56.731 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 44d+20:48:56.731 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 44d+20:48:56.730 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 44d+20:48:56.730 SET FEATURES [set transfer mode] Error 3 occurred at disk power-on lifetime: 1076 hours (44 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 44d+20:48:56.606 READ DMA EXT ef 10 02 00 00 00 a0 00 44d+20:48:56.606 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 44d+20:48:56.606 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 44d+20:48:56.605 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 44d+20:48:56.605 SET FEATURES [set transfer mode] Error 2 occurred at disk power-on lifetime: 1076 hours (44 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 44d+20:48:56.451 READ DMA EXT 25 00 08 ff ff ff ef 00 44d+20:48:56.450 READ DMA EXT 25 00 08 ff ff ff ef 00 44d+20:48:56.443 READ DMA EXT 25 00 08 ff ff ff ef 00 44d+20:48:56.437 READ DMA EXT 25 00 08 ff ff ff ef 00 44d+20:48:56.430 READ DMA EXT Error 1 occurred at disk power-on lifetime: 1076 hours (44 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 10 b2 06 e0 00 44d+20:48:55.925 READ DMA ca 00 08 98 8f 00 e0 00 44d+20:48:21.660 WRITE DMA c8 00 08 98 8f 00 e0 00 44d+20:48:21.660 READ DMA ca 00 c0 d8 8e 00 e0 00 44d+20:48:21.659 WRITE DMA ca 00 08 d0 8e 00 e0 00 44d+20:48:21.659 WRITE DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
cassiusdrow Posted May 28, 2015 Posted May 28, 2015 I'd err on the side of caution. I wouldn't use it for anything I cared about. I've had three failures of this model drive in the last two months with drives aged about two years.
HellDiverUK Posted May 28, 2015 Posted May 28, 2015 ST3000DM001 is the drive that BackBlaze had terrible results with, something like 48% annual failure rate. I'd nuke that drive from orbit, because it's the only way to be sure.
jus7incase Posted May 28, 2015 Author Posted May 28, 2015 This is what I get after the pre-clear, basically the same figures as captured during the pre-clear: ** Changed attributes in files: /tmp/smart_start_sdc /tmp/smart_finish_sdc ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 109 114 6 ok 21345144 Seek_Error_Rate = 51 51 30 near_thresh 1383022160179 Spin_Retry_Count = 100 100 97 near_thresh 0 End-to-End_Error = 93 93 99 FAILING_NOW 7 Airflow_Temperature_Cel = 63 67 45 near_thresh 37 Temperature_Celsius = 37 33 0 ok 37 *** Failing SMART Attributes in /tmp/smart_finish_sdc *** ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 184 End-to-End_Error 0x0032 093 093 099 Old_age Always FAILING_NOW 7 What does feature 184 tell me? The other errors are quite old. Update: The drive is still under warranty, trying to get it replaced.
3605481mah Posted June 2, 2015 Posted June 2, 2015 ST3000DM001 is the drive that BackBlaze had terrible results with, something like 48% annual failure rate. I'd nuke that drive from orbit, because it's the only way to be sure. +1. Could not agree more about that model.
c3 Posted June 2, 2015 Posted June 2, 2015 Duh. How? https://apps1.seagate.com/downloads/request.html
Recommended Posts
Archived
This topic is now archived and is closed to further replies.