Preclear.sh results - Questions about your results? Post them here.


Recommended Posts

I already knew this drive was bad - just how bad is it? Should I just toss it? It took a looong time preclear, lol:

 

========================================================================1.15
== invoked as: ./preclear_disk.sh /dev/sdh
== WDCWD20EADS-00R6B0   WD-WCAVY1843494
== Disk /dev/sdh has been successfully precleared
== with a starting sector of 63 
== Ran 1 cycle
==
== Using :Read block size = 8388608 Bytes
== Last Cycle's Pre Read Time  : 48:48:17 (11 MB/s)
== Last Cycle's Zeroing time   : 7:46:57 (71 MB/s)
== Last Cycle's Post Read Time : 35:57:51 (15 MB/s)
== Last Cycle's Total Time     : 92:34:42
==
== Total Elapsed Time 92:34:42
==
== Disk Start Temperature: 29C
==
== Current Disk Temperature: 31C, 
==
============================================================================
** Changed attributes in files: /tmp/smart_start_sdh  /tmp/smart_finish_sdh
                ATTRIBUTE   NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS      RAW_VALUE
      Raw_Read_Error_Rate =   181     182           51        ok          1250509
    Reallocated_Sector_Ct =    41      43          140        FAILING_NOW 1265
          Seek_Error_Rate =   100     200            0        ok          0
      Temperature_Celsius =   121     123            0        ok          31
  Reallocated_Event_Count =     1       1            0        near_thresh 1076

*** Failing SMART Attributes in /tmp/smart_finish_sdh *** 
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  5 Reallocated_Sector_Ct   0x0033   041   041   140    Pre-fail  Always   FAILING_NOW 1265

24 sectors were pending re-allocation before the start of the preclear.
24 sectors were pending re-allocation after pre-read in cycle 1 of 1.
16 sectors were pending re-allocation after zero of disk in cycle 1 of 1.
16 sectors are pending re-allocation at the end of the preclear,
    a change of -8 in the number of sectors pending re-allocation.
1256 sectors had been re-allocated before the start of the preclear.
1265 sectors are re-allocated at the end of the preclear,
    a change of 9 in the number of sectors re-allocated.
SMART overall-health status =  FAILED! 
============================================================================

BAD!
Link to comment

Thanks.  I see we have the same zeroing speed, but the difference arises on the read phases - yours are much faster indeed. 

 

What I am surprised at is to see you got almost the same post-read speed as pre-read speed.  In my experience, post-read is usually about half pre-read speed.  But perhaps thats the different script - I use the standard version.

 

And this is exactly why I use the modified script, since it makes 3 cycle preclear times a bit more manageable. A 3 cycle run on 4TB HGST drive is 74-75 hours.

 

== invoked as: ./preclear_bjp.sh -f -c 3 -A /dev/sde
== HGSTHDN724040ALE640 
== Disk /dev/sde has been successfully precleared
== with a starting sector of 1 
== Ran 3 cycles
==
== Using :Read block size = 1000448 Bytes
== Last Cycle's Pre Read Time  : 12:11:43 (91 MB/s)
== Last Cycle's Zeroing time   : 8:39:55 (128 MB/s)
== Last Cycle's Post Read Time : 12:17:47 (90 MB/s)
== Last Cycle's Total Time     : 20:58:46
==
== Total Elapsed Time 75:07:02
==
== Disk Start Temperature: 32C
==
== Current Disk Temperature: 35C, 

 

== invoked as: ./preclear_bjp.sh -f -c 3 -A /dev/sdc
== HGSTHDN724040ALE640
== Disk /dev/sdc has been successfully precleared
== with a starting sector of 1 
== Ran 3 cycles
==
== Using :Read block size = 1000448 Bytes
== Last Cycle's Pre Read Time  : 12:02:23 (92 MB/s)
== Last Cycle's Zeroing time   : 8:32:16 (130 MB/s)
== Last Cycle's Post Read Time : 12:07:32 (91 MB/s)
== Last Cycle's Total Time     : 20:40:53
==
== Total Elapsed Time 74:04:51
==
== Disk Start Temperature: 28C
==
== Current Disk Temperature: 31C, 

Link to comment

Hello,

 

I've run pre-clear on three Seagate 4TB ST4000VN000 drives, but am a little uncertain about how to interpret the results. I've been reading in the forum here for the past 90 minutes and feel simultaneously more educated and more confused.  :P

It seems the drives are healthy, but I'd like to make certain.

 

At step 11 of the Configuration Tutorial it suggests attaching the preclear reports to a forum post. I've done so here (it also mentioned how to put the results in a single text file, but the command only seemed to apply to the last preclear session).

 

Thanks in advance!  :)

preclear_reports.zip

Link to comment

Hello,

 

I've run pre-clear on three Seagate 4TB ST4000VN000 drives, but am a little uncertain about how to interpret the results. I've been reading in the forum here for the past 90 minutes and feel simultaneously more educated and more confused.  :P

It seems the drives are healthy, but I'd like to make certain.

 

At step 11 of the Configuration Tutorial it suggests attaching the preclear reports to a forum post. I've done so here (it also mentioned how to put the results in a single text file, but the command only seemed to apply to the last preclear session).

 

Thanks in advance!  :)

 

You have a few unusual readings ...

7G0

 

188 Command_Timeout        0x0032  100  099  000    Old_age  Always      -      1

199 UDMA_CRC_Error_Count    0x003e  200  200  000    Old_age  Always      -      2

 

These may be indicative of a loose cable. Odd though, thought you'd see some ATA errors with CRC errors.

26w

 

199 UDMA_CRC_Error_Count    0x003e  200  200  000    Old_age  Always      -      4

 

Similar. Should not be getting CRC errors.

bxn

 

199 UDMA_CRC_Error_Count    0x003e  200  200  000    Old_age  Always      -      8

 

More CRC errors.

 

I would not be too happy with these results. I have never seen this type of behavior. Given you got a few of these on each drive I might conclude that it was the controller or some other common denominator of all drives (all on same SAS/SATA connector)?

 

Or I could easily blame it on Seagate, who'se quality has not been stellar for quite some time. But their 4TB have been pretty well regarded recently so this is surprising.

 

Inviting other opinions. Anyone seen this before?

 

I think I might try running another preclear cycle hooked to a different computer hooked to motherboard ports. Note that once these attributes increment - they never go back to zero. But if you preclear on a different server and they don't go up, it is something related to the other server and not with the drive. If they keep creeping upward, I'd be tempted to send them back and spend a few more bucks to get the HGSTs.

Link to comment

Given you got a few of these on each drive I might conclude that it was the controller or some other common denominator of all drives (all on same SAS/SATA connector)?

 

Hm, maybe it'll help to know that these disks are mounted in the hot-swap drive cage of a Lian Li PC-Q25B case which is connected to an ASUS H87I-PLUS motherboard.

So these are using mobo ports then?

 

I have that hardware and no problems. I'm sure others do as well.

Link to comment

I am having trouble preclearing a Seagate 4tb drive.  Every time that I attempt to perform a preclear it hangs on step two.  When it freezes, if I go to the console the monitor keeps refreshing "No such file or directory exists dev/sde."

 

Please see my original thread here with error logs - http://lime-technology.com/forum/index.php?topic=38014.0

Then it indicates your disk is dropping off-line in some way and can no longer be accessed.  (either a bad disk, or a power supply that cannot supply proper power to the disk, or a disk controller that is stopping to respond, or a loose cable or connector, or loose drive tray, or back-plane. )

 

Sorry to say, difficiult to isolate which it might be)

Link to comment

I am having trouble preclearing a Seagate 4tb drive.  Every time that I attempt to perform a preclear it hangs on step two.  When it freezes, if I go to the console the monitor keeps refreshing "No such file or directory exists dev/sde."

 

Please see my original thread here with error logs - http://lime-technology.com/forum/index.php?topic=38014.0

Then it indicates your disk is dropping off-line in some way and can no longer be accessed.  (either a bad disk, or a power supply that cannot supply proper power to the disk, or a disk controller that is stopping to respond, or a loose cable or connector, or loose drive tray, or back-plane. )

 

Sorry to say, difficiult to isolate which it might be)

 

Thanks Joe.  I think that I am just going to RMA the drive even thought it passes all of the Seagate SeaTools tests. 

 

I am using a Norco 4224 case and I have tried preclearing the drive in multiple slots to eliminate the possibility of a bad cable, or PCI-E card with no luck.  I was able to preclear an old 2 TB drive just fine so I am suspecting the drive.

Link to comment

I am having trouble preclearing a Seagate 4tb drive.  Every time that I attempt to perform a preclear it hangs on step two.  When it freezes, if I go to the console the monitor keeps refreshing "No such file or directory exists dev/sde."

 

Please see my original thread here with error logs - http://lime-technology.com/forum/index.php?topic=38014.0

Then it indicates your disk is dropping off-line in some way and can no longer be accessed.  (either a bad disk, or a power supply that cannot supply proper power to the disk, or a disk controller that is stopping to respond, or a loose cable or connector, or loose drive tray, or back-plane. )

 

Sorry to say, difficiult to isolate which it might be)

 

Thanks Joe.  I think that I am just going to RMA the drive even thought it passes all of the Seagate SeaTools tests. 

 

I am using a Norco 4224 case and I have tried preclearing the drive in multiple slots to eliminate the possibility of a bad cable, or PCI-E card with no luck.  I was able to preclear an old 2 TB drive just fine so I am suspecting the drive.

Better to RMA the drive now, then to have it stop responding when attempting to load it with your data (or fail when using it to recover another failed disk).

 

Joe L.

Link to comment

My Cache Drive failed last week after a good 7 years or so of use.  I bought a new WD Blue 1TB drive, and started the preclear process...  Except that, it doesn't seem to be moving.

 

The first preclear I attempted started fine.  The pre read was going around 150 megabytes before I left for work.  When I came back, it dropped to less than 3 megabytes.  I stopped the preclear and changed the drive's location within the server and attempted another preclear.  Same issue.  Here is what I see on the 3rd attempt after moving the drive again:

 

o553cE6.png

 

Here's a Smart test

 

smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Caviar Blue (SATA 6Gb/s)
Device Model:     WDC WD10EZEX-00BN5A0
Serial Number:    WD-WCC3F4XHKHY7
LU WWN Device Id: 5 0014ee 2b5e1c237
Firmware Version: 01.01A01
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sun Feb 22 14:19:25 2015 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80)	Offline data collection activity
				was never started.
				Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 241)	Self-test routine in progress...
				10% of test remaining.
Total time to complete Offline 
data collection: 		(12360) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 128) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x3035)	SCT Status supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       20
  3 Spin_Up_Time            0x0027   100   253   021    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       1
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       23
10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       1
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       0
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       5
194 Temperature_Celsius     0x0022   108   108   000    Old_age   Always       -       35
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       172
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

Bad drive, I'm guessing?

Link to comment

based on the smart report, it is highly likely to be bad cabling to the drive, or cabling picking up noise from adjacent cables.

(if you neatly tie-wrapped all the drive cables, you've caused the problem.  Do NOT run the cables all parallel to each other or to power cables.)

 

It might also possibly indicate a power supply at its limits, with the power supplied to the drive being noisy causing the checksum errors in communicating with the drive that are showing in the SMART report:

199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      172
Link to comment

Hey everyone,

 

just finished the second preclear cycle on a new drive. Maybe you can take a quick look at the details

 

#2

Feb 28 19:01:25 Server preclear_disk-diff[757]: SMART Attributes Data Structure revision number: 10
Feb 28 19:01:25 Server preclear_disk-diff[757]: Vendor Specific SMART Attributes with Thresholds:
Feb 28 19:01:25 Server preclear_disk-diff[757]: ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
Feb 28 19:01:25 Server preclear_disk-diff[757]:   1 Raw_Read_Error_Rate     0x000f   110   099   006    Pre-fail  Always       -       28073888
Feb 28 19:01:25 Server preclear_disk-diff[757]:   3 Spin_Up_Time            0x0003   097   097   000    Pre-fail  Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]:   4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       5
Feb 28 19:01:25 Server preclear_disk-diff[757]:   5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]:   7 Seek_Error_Rate         0x000f   060   060   030    Pre-fail  Always       -       1118246
Feb 28 19:01:25 Server preclear_disk-diff[757]:   9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       43
Feb 28 19:01:25 Server preclear_disk-diff[757]:  10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]:  12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       5
Feb 28 19:01:25 Server preclear_disk-diff[757]: 183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 189 High_Fly_Writes         0x003a   098   098   000    Old_age   Always       -       2
Feb 28 19:01:25 Server preclear_disk-diff[757]: 190 Airflow_Temperature_Cel 0x0022   064   063   045    Old_age   Always       -       36 (Min/Max 18/37)
Feb 28 19:01:25 Server preclear_disk-diff[757]: 191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       3
Feb 28 19:01:25 Server preclear_disk-diff[757]: 193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       16
Feb 28 19:01:25 Server preclear_disk-diff[757]: 194 Temperature_Celsius     0x0022   036   040   000    Old_age   Always       -       36 (0 18 0 0 0)
Feb 28 19:01:25 Server preclear_disk-diff[757]: 197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
Feb 28 19:01:25 Server preclear_disk-diff[757]: 240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       42h+40m+12.024s
Feb 28 19:01:25 Server preclear_disk-diff[757]: 241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       11721066432
Feb 28 19:01:25 Server preclear_disk-diff[757]: 242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       24114452099
Feb 28 19:01:25 Server preclear_disk-diff[757]: 
Feb 28 19:01:25 Server preclear_disk-diff[757]: SMART Error Log Version: 1
Feb 28 19:01:25 Server preclear_disk-diff[757]: No Errors Logged

 

It seems good to me but what do I know :)  Thanks!

Link to comment

hey guys,

 

Just ran pre-clear on a few of my drives, can someone take a look and let me know if they are good to go.

 

Disk 1:

 

Disk: /dev/sdc
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.18.5-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda Green (AF)
Device Model:     ST2000DL003-9VT166
Serial Number:    5YD4Z2TN
LU WWN Device Id: 5 000c50 03e0bb439
Firmware Version: CC32
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5900 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Mar  3 15:27:17 2015 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
				was completed without error.
				Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		(  623) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 333) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x30b7)	SCT Status supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   099   006    Pre-fail  Always       -       153199328
  3 Spin_Up_Time            0x0003   093   092   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       774
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   070   060   030    Pre-fail  Always       -       12917718228
  9 Power_On_Hours          0x0032   090   090   000    Old_age   Always       -       9524
10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       754
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   068   047   045    Old_age   Always       -       32 (Min/Max 26/34)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       732
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       775
194 Temperature_Celsius     0x0022   032   053   000    Old_age   Always       -       32 (0 23 0 0 0)
195 Hardware_ECC_Recovered  0x001a   036   006   000    Old_age   Always       -       153199328
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       147240068850970
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       1103622127
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       3045207336

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

Disk 2:

Disk: /dev/sdd
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.18.5-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda Green (AF)
Device Model:     ST2000DL003-9VT166
Serial Number:    6YD0Y70T
LU WWN Device Id: 5 000c50 03dfffe17
Firmware Version: CC32
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5900 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Mar  4 19:37:24 2015 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
				was completed without error.
				Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		(  612) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 331) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x30b7)	SCT Status supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   099   006    Pre-fail  Always       -       165825160
  3 Spin_Up_Time            0x0003   093   092   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       776
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   075   060   030    Pre-fail  Always       -       37001928
  9 Power_On_Hours          0x0032   090   090   000    Old_age   Always       -       9545
10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       758
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   099   000    Old_age   Always       -       1
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   070   049   045    Old_age   Always       -       30 (Min/Max 27/32)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       736
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       777
194 Temperature_Celsius     0x0022   030   051   000    Old_age   Always       -       30 (0 22 0 0 0)
195 Hardware_ECC_Recovered  0x001a   036   008   000    Old_age   Always       -       165825160
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       3637837309203
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       101116939
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       3455378606

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 

Disk 3:

 

Disk: /dev/sdf
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.18.5-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD40EZRX-00SPEB0
Serial Number:    WD-WCC4E4XV66XA
LU WWN Device Id: 5 0014ee 2b6250389
Firmware Version: 80.00A80
User Capacity:    4,000,787,030,016 bytes [4.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Wed Mar  4 05:56:42 2015 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80)	Offline data collection activity
				was never started.
				Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		(52380) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 524) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x7035)	SCT Status supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   184   183   021    Pre-fail  Always       -       7766
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       46
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       205
10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       31
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       12
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       255
194 Temperature_Celsius     0x0022   123   109   000    Old_age   Always       -       29
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Link to comment

Disk 4:

 

Disk: /dev/sde
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.18.5-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda Green (AF)
Device Model:     ST2000DL003-9VT166
Serial Number:    5YD4YHA1
LU WWN Device Id: 5 000c50 03e0d7753
Firmware Version: CC32
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5900 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Mar  5 10:37:01 2015 IST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
				was completed without error.
				Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		(  623) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 342) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x30b7)	SCT Status supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   099   006    Pre-fail  Always       -       155601248
  3 Spin_Up_Time            0x0003   093   092   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       767
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   075   060   030    Pre-fail  Always       -       4331606884
  9 Power_On_Hours          0x0032   090   090   000    Old_age   Always       -       9594
10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       755
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   070   048   045    Old_age   Always       -       30 (Min/Max 27/32)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       734
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       769
194 Temperature_Celsius     0x0022   030   052   000    Old_age   Always       -       30 (0 22 0 0 0)
195 Hardware_ECC_Recovered  0x001a   036   009   000    Old_age   Always       -       155601248
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       105630425687345
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       714450761
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       659789449

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Link to comment

howdy, results of a new hdd. all ok?

 

START

Disk: /dev/sdj
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.18.5-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red (AF)
Device Model:     WDC WD30EFRX-68EUZN0
Serial Number:    WD-WCC4N3HZTH6K
LU WWN Device Id: 5 0014ee 2b65337bd
Firmware Version: 82.00A82
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Mar  4 14:20:06 2015 AEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
				was never started.
				Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		(40980) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 411) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x703d)	SCT Status supported.
				SCT Error Recovery Control supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   253   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   100   253   021    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       4
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       0
10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       4
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       1
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       2
194 Temperature_Celsius     0x0022   117   117   000    Old_age   Always       -       33
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   253   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

RPT

========================================================================1.15
== invoked as: ./preclear_disk.sh /dev/sdj
== WDCWD30EFRX-68EUZN0   WD-WCC4N3HZTH6K
== Disk /dev/sdj has been successfully precleared
== with a starting sector of 1 
== Ran 1 cycle
==
== Using :Read block size = 1000448 Bytes
== Last Cycle's Pre Read Time  : 8:29:10 (98 MB/s)
== Last Cycle's Zeroing time   : 6:54:41 (120 MB/s)
== Last Cycle's Post Read Time : 16:16:47 (51 MB/s)
== Last Cycle's Total Time     : 31:41:38
==
== Total Elapsed Time 31:41:38
==
== Disk Start Temperature: 33C
==
== Current Disk Temperature: 35C, 
==
============================================================================
** Changed attributes in files: /tmp/smart_start_sdj  /tmp/smart_finish_sdj
                ATTRIBUTE   NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS      RAW_VALUE
      Temperature_Celsius =   115     117            0        ok          35
No SMART attributes are FAILING_NOW

0 sectors were pending re-allocation before the start of the preclear.
0 sectors were pending re-allocation after pre-read in cycle 1 of 1.
0 sectors were pending re-allocation after zero of disk in cycle 1 of 1.
0 sectors are pending re-allocation at the end of the preclear,
    the number of sectors pending re-allocation did not change.
0 sectors had been re-allocated before the start of the preclear.
0 sectors are re-allocated at the end of the preclear,
    the number of sectors re-allocated did not change. 
============================================================================

 

FINISH

Disk: /dev/sdj
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.18.5-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red (AF)
Device Model:     WDC WD30EFRX-68EUZN0
Serial Number:    WD-WCC4N3HZTH6K
LU WWN Device Id: 5 0014ee 2b65337bd
Firmware Version: 82.00A82
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Mar  5 22:01:43 2015 AEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
				was never started.
				Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		(40980) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 411) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x703d)	SCT Status supported.
				SCT Error Recovery Control supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   100   253   021    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       4
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       34
10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       4
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       1
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       2
194 Temperature_Celsius     0x0022   115   111   000    Old_age   Always       -       35
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

Link to comment
  • 4 weeks later...

Hi folks,

 

Can anyone take a look at the attached logs for preclear on three 6TB Seagate drives (ST6000DX000-1H217Z) and let me know if there is anything of concern please? There was some weird stuff about error rates which i didn't quite understand and thought may have been a bit suspect.

 

I can post the _finish and _start logs if needed.

 

many thanks

 

p.s preclear on three 6TB disks simultaneously took a whopping 55hrs and 38mins :)

preclear_rpt_Z4D0D6Y6_2015-03-27.txt

preclear_rpt_Z4D0E7T7_2015-03-27.txt

preclear_rpt_Z4D0711K_2015-03-27.txt

Link to comment

Hi folks,

 

Can anyone take a look at the attached logs for preclear on three 6TB Seagate drives (ST6000DX000-1H217Z) and let me know if there is anything of concern please? There was some weird stuff about error rates which i didn't quite understand and thought may have been a bit suspect.

 

I can post the _finish and _start logs if needed.

 

many thanks

 

p.s preclear on three 6TB disks simultaneously took a whopping 55hrs and 38mins :)

 

All three look okay. The drive temps are warm though. In the low to mid 40s. That is okay but I prefer to see them in the 30s. You might consider a little extra cooling. The ECC recovered attribute is a little unsettling, but modern drives store data with redundancy acknowledging that media related errors will exist and that the redundancy is used in the normal usage use case to detect and correct such errors. Seagate it's very upfront reporting this, whereas other drives either mask this activity our have it occur to a lesser extent.

 

My slight personal bias against Seagate not withstanding, these drives have successfully passed the preclear. I suggest, as with any drive, that you continue to monitor the smart reports over time.

Link to comment

Hi folks,

 

Can anyone take a look at the attached logs for preclear on three 6TB Seagate drives (ST6000DX000-1H217Z) and let me know if there is anything of concern please? There was some weird stuff about error rates which i didn't quite understand and thought may have been a bit suspect.

 

I can post the _finish and _start logs if needed.

 

many thanks

 

p.s preclear on three 6TB disks simultaneously took a whopping 55hrs and 38mins :)

 

All three look okay. The drive temps are warm though. In the low to mid 40s. That is okay but I prefer to see them in the 30s. You might consider a little extra cooling. The ECC recovered attribute is a little unsettling, but modern drives store data with redundancy acknowledging that media related errors will exist and that the redundancy is used in the normal usage use case to detect and correct such errors. Seagate it's very upfront reporting this, whereas other drives either mask this activity our have it occur to a lesser extent.

 

My slight personal bias against Seagate not withstanding, these drives have successfully passed the preclear. I suggest, as with any drive, that you continue to monitor the smart reports over time.

 

 

thanks so much for looking at the logs. Agreed - the temps are a little hotter than ideal, but I livve in Australia and the ambient here was about 33 when i ran the preclear. I am actually looking to run the 6TB drives in a new enclosure and am currently investigating the best options for what my next unraid build will be.

 

cheers

 

 

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.