Preclear.sh results - Questions about your results? Post them here.


Recommended Posts

Hi all,

 

Can someone please take a quick look at this syslog of a drive that I gave precleared. The drive is a 1.5TB Seagate ST31500541AS. I have tried to interpret the data compared to other Seagates and I think it is OK (I hope) 

 

Thank you

 

 

unRaid preclear_disk-finish[26499]: smartctl version 5.38 [i486-slackware-linux-gnu] Copyright © 2002-8 Bruce Allen

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Home page is http://smartmontools.sourceforge.net/

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: === START OF INFORMATION SECTION ===

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Device Model:    ST31500541AS

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Serial Number:    9XW058TZ

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Firmware Version: CC35

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: User Capacity:    1,500,301,910,016 bytes

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Device is:        Not in smartctl database [for details use: -P showall]

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ATA Version is:  8

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ATA Standard is:  ATA-8-ACS revision 4

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Local Time is:    Wed Dec 22 17:56:17 2010 GMT

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART support is: Available - device has SMART capability.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART support is: Enabled

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: === START OF READ SMART DATA SECTION ===

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART overall-health self-assessment test result: PASSED

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: See vendor-specific Attribute list for marginal Attributes.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: General SMART Values:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Offline data collection status:  (0x00)^IOffline data collection activity

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^Iwas never started.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^IAuto Offline Data Collection: Disabled.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Self-test execution status:      (  0)^IThe previous self-test routine completed

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^Iwithout error or no self-test has ever

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^Ibeen run.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Total time to complete Offline

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: data collection: ^I^I ( 653) seconds.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Offline data collection

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: capabilities: ^I^I^I (0x73) SMART execute Offline immediate.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^IAuto Offline data collection on/off support.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^ISuspend Offline collection upon new

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^Icommand.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^INo Offline surface scan supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^ISelf-test supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^IConveyance Self-test supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^ISelective Self-test supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART capabilities:            (0x0003)^ISaves SMART data before entering

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^Ipower-saving mode.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^ISupports SMART auto save timer.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Error logging capability:        (0x01)^IError logging supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^IGeneral Purpose Logging supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Short self-test routine

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: recommended polling time: ^I (  1) minutes.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Extended self-test routine

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: recommended polling time: ^I ( 255) minutes.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Conveyance self-test routine

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: recommended polling time: ^I (  2) minutes.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SCT capabilities: ^I      (0x103f)^ISCT Status supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^ISCT Feature Control supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ^I^I^I^I^ISCT Data Table supported.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART Attributes Data Structure revision number: 10

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Vendor Specific SMART Attributes with Thresholds:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  1 Raw_Read_Error_Rate    0x000f  119  099  006    Pre-fail  Always      -      218828031

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  3 Spin_Up_Time            0x0003  100  100  000    Pre-fail  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  4 Start_Stop_Count        0x0032  100  100  020    Old_age  Always      -      104

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  5 Reallocated_Sector_Ct  0x0033  100  100  036    Pre-fail  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  7 Seek_Error_Rate        0x000f  063  060  030    Pre-fail  Always      -      1894725

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  9 Power_On_Hours          0x0032  100  100  000    Old_age  Always      -      423

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  10 Spin_Retry_Count        0x0013  100  100  097    Pre-fail  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  12 Power_Cycle_Count      0x0032  100  100  020    Old_age  Always      -      66

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 183 Unknown_Attribute      0x0032  100  100  000    Old_age  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 184 Unknown_Attribute      0x0032  100  100  099    Old_age  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 187 Reported_Uncorrect      0x0032  100  100  000    Old_age  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 188 Unknown_Attribute      0x0032  100  100  000    Old_age  Always      -      4295032833

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 189 High_Fly_Writes        0x003a  092  092  000    Old_age  Always      -      8

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 190 Airflow_Temperature_Cel 0x0022  065  045  045    Old_age  Always  In_the_past 35 (Lifetime Min/Max 17/35)

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 195 Hardware_ECC_Recovered  0x001a  063  043  000    Old_age  Always      -      218828031

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 197 Current_Pending_Sector  0x0012  100  100  000    Old_age  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 198 Offline_Uncorrectable  0x0010  100  100  000    Old_age  Offline      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 199 UDMA_CRC_Error_Count    0x003e  200  200  000    Old_age  Always      -      0

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 240 Head_Flying_Hours      0x0000  100  253  000    Old_age  Offline      -      140265041953285

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 241 Unknown_Attribute      0x0000  100  253  000    Old_age  Offline      -      1593608245

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: 242 Unknown_Attribute      0x0000  100  253  000    Old_age  Offline      -      4184370610

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART Error Log Version: 1

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: No Errors Logged

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART Self-test log structure revision number 1

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: # 1  Short offline      Completed without error      00%        27        -

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: SMART Selective self-test log data structure revision number 1

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:    1        0        0  Not_testing

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:    2        0        0  Not_testing

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:    3        0        0  Not_testing

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:    4        0        0  Not_testing

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:    5        0        0  Not_testing

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: Selective self-test flags (0x0):

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:  After scanning selected spans, do NOT read-scan remainder of disk.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]: If Selective self-test is pending on power-up, resume after 0 minute delay.

Dec 22 17:56:18 unRaid preclear_disk-finish[26499]:

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ============================================================================

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ==

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Disk /dev/sda has been successfully precleared

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ==

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Ran 1 preclear-disk cycle

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ==

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Using :Read block size = 8225280 Bytes

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Last Cycle's Pre Read Time  : 6:12:43 (67 MB/s)

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Last Cycle's Zeroing time  : 5:36:54 (74 MB/s)

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Last Cycle's Post Read Time : 12:02:24 (34 MB/s)

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Last Cycle's Total Time    : 23:53:07

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ==

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Total Elapsed Time 23:53:07

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ==

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Disk Start Temperature: 20C

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ==

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: == Current Disk Temperature: 35C,

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ==

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ============================================================================

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: S.M.A.R.T. error count differences detected after pre-clear

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: note, some 'raw' values may change, but not be an indication of a problem

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: 55c55

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: <  1 Raw_Read_Error_Rate    0x000f  114  099  006    Pre-fail  Always      -      63775178

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ---

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: >  1 Raw_Read_Error_Rate    0x000f  119  099  006    Pre-fail  Always      -      218828031

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: 59c59

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: <  7 Seek_Error_Rate        0x000f  062  060  030    Pre-fail  Always      -      1751965

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ---

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: >  7 Seek_Error_Rate        0x000f  063  060  030    Pre-fail  Always      -      1894725

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: 67,68c67,68

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: < 190 Airflow_Temperature_Cel 0x0022  080  045  045    Old_age  Always  In_the_past 20 (Lifetime Min/Max 17/20)

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: < 195 Hardware_ECC_Recovered  0x001a  057  043  000    Old_age  Always     

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ---

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: > 190 Airflow_Temperature_Cel 0x0022  065  045  045    Old_age  Always  In_the_past 35 (Lifetime Min/Max 17/35)

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: > 195 Hardware_ECC_Recovered  0x001a  063  043  000    Old_age  Always     

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: 72,74c72,74

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: < 240 Head_Flying_Hours      0x0000  100  253  000    Old_age  Offline      -      198135431299565

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: < 241 Unknown_Attribute      0x0000  100  253  000    Old_age  Offline      -      2958636950

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: < 242 Unknown_Attribute      0x0000  100  253  000    Old_age  Offline      -      3262049093

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ---

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: > 240 Head_Flying_Hours      0x0000  100  253  000    Old_age  Offline      -      140265041953285

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: > 241 Unknown_Attribute      0x0000  100  253  000    Old_age  Offline      -      1593608245

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: > 242 Unknown_Attribute      0x0000  100  253  000    Old_age  Offline      -      4184370610

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: ============================================================================

Dec 22 17:56:18 unRaid preclear_disk-diff[26512]: 

syslog-2010-12-22_2.txt

Link to comment

Hi all,

 

Can someone please take a quick look at this syslog of a drive that I gave precleared. The drive is a 1.5TB Seagate ST31500541AS. I have tried to interpret the data compared to other Seagates and I think it is OK (I hope) 

Your drive looks great.

Thank you

You are welcome.

 

Link to comment

Hi!  First time trying to run preclear as well as setup UnRAID.  Did 3 drives at the same time.  2 Seagate(2TB), and 1 WD20ears (with jumper)  and was wondering if my results look ok.  The high errors compared to the WDC threw me off.  Thanks in advance!!  Planning on running them again, just need a baseline to see what I need to look for.

WDC1Status.txt

Seagate2Status.txt

Seagate1Status.txt

syslog122510.txt

Link to comment

Once again, Preclear.sh only reports DIFFERENCES between SMART reports before and after. Your drive could be failing before and if afterwards it fails exactly the same, the Preclear.sh will not show any differences. Your drive could be perfectly fine before and if afterwards it's exactly the same, it won't show any differences.

 

On the SMART reports, you need to compare the "VALUE" and "WORST" to the "THRESHOLD". As long as those first two VALUE and WORST are above TRESHOLD you should be fine as long as the "WHEN_FAILED" column is clear.

 

In most cases the RAW_VALUE is only of interest to the drive manufacturer, though there are some few data items that are of interest to the users, Id #5 - Reallocated_Sector_Ct, Id #196 - Reallocated_Event_Count, Id #197 - Current_Pending_Sector, Id #198 - Offline_Uncorrectable.

 

I do not see any "errors" on your drive reports.

Link to comment

I'm trying to preclear a Seagate 500 gb hdd and it stuck at 70% for a while and then a "killed message came up on the screen. My syslog is to big to post but here is a flavour. Syslog is 1.6GB

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] Sense Key : 0xb [current] [descriptor]

Dec 12 19:15:56 Tower kernel: Descriptor sense data with sense descriptors (in hex):

Dec 12 19:15:56 Tower kernel: 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00

Dec 12 19:15:56 Tower kernel: 00 00 00 0f

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] ASC=0x0 ASCQ=0x0

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] CDB: cdb[0]=0x28: 28 00 37 3f e9 10 00 00 08 00

Dec 12 19:15:56 Tower kernel: end_request: I/O error, dev sdb, sector 926935312

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] Sense Key : 0xb [current] [descriptor]

Dec 12 19:15:56 Tower kernel: Descriptor sense data with sense descriptors (in hex):

Dec 12 19:15:56 Tower kernel: 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00

Dec 12 19:15:56 Tower kernel: 00 00 00 97

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] ASC=0x0 ASCQ=0x0

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] CDB: cdb[0]=0x28: 28 00 37 3f ea 98 00 00 08 00

Dec 12 19:15:56 Tower kernel: end_request: I/O error, dev sdb, sector 926935704

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] Sense Key : 0xb [current] [descriptor]

Dec 12 19:15:56 Tower kernel: Descriptor sense data with sense descriptors (in hex):

Dec 12 19:15:56 Tower kernel: 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00

Dec 12 19:15:56 Tower kernel: 00 00 00 1f

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] ASC=0x0 ASCQ=0x0

Dec 12 19:15:56 Tower kernel: sd 0:0:0:0: [sdb] CDB: cdb[0]=0x28: 28 00 37 3f ec 20 00 00 08 00

Dec 12 19:15:56 Tower kernel: end_request: I/O error, dev sdb, sector 926936096

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

Dec 12 19:15:56 Tower kernel: ata1: status=0x41 { DriveReady Error }

Dec 12 19:15:56 Tower kernel: ata1: error=0x04 { DriveStatusError }

Dec 12 19:15:56 Tower kernel: ata1: translated ATA stat/err 0x41/04 to SCSI SK/ASC/ASCQ 0xb/00/00

 

Is the hdd faulty?

A few minutes later the system locked up.

 

Will have to reboot

 

 

I still have to retest this Seagate hdd which is a warranty return, Originally I ran this with two other pre-clears and everything ground to a halt and I had to reboot and i could not tell if the pre-clears finished on the other hdd's so I ran the pre-clear script on each drive individually.

Should I bother to run a pre-clear on this hdd and will it just do the same again and fill up my ram untill the pc hangs.

 

Thank you

 

Link to comment

It will likely fill the syslog and crash the server again...  but if you start it and see the errors in the syslog, just stop it.  It is probably just a bad drive, unless it is a bad disk controller port, or a power supply unable to keep up with the power demands. ;)

 

Thanks Joe L.

I tried the hdd on the mobo port and an mv8 card, the hard drive failed both times, power supply is single rail  650 watt so should be no issues there. I will run the seagate tool on the drive see what happens.

Trouble is a 500gb hdd is hardly worth the postage cost to return it now  :D

Link to comment

It will likely fill the syslog and crash the server again...  but if you start it and see the errors in the syslog, just stop it.  It is probably just a bad drive, unless it is a bad disk controller port, or a power supply unable to keep up with the power demands. ;)

 

Thanks Joe L.

I tried the hdd on the mobo port and an mv8 card, the hard drive failed both times, power supply is single rail  650 watt so should be no issues there. I will run the seagate tool on the drive see what happens.

Trouble is a 500gb hdd is hardly worth the postage cost to return it now  :D

True, but some have reported a larger drive is sent in return...  who knows, it might turn into a 1TB drive.
Link to comment

How do my 3 drives look?

============================================================================

==

== Disk /dev/sda has been successfully precleared

==

============================================================================

S.M.A.R.T. error count differences detected after pre-clear

note, some 'raw' values may change, but not be an indication of a problem

19,20c19,20

< Offline data collection status:  (0x80)       Offline data collection activity

<                                       was never started.

---

> Offline data collection status:  (0x84)       Offline data collection activity

>                                       was suspended by an interrupting command from host.

54c54

<   1 Raw_Read_Error_Rate     0x002f   100   253   051    Pre-fail  Always       -       0

---

>   1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0

58c58

<   7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0

---

>   7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0

63c63

< 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       12

---

> 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       13

67c67

< 199 UDMA_CRC_Error_Count    0x0032   200   253   000    Old_age   Always       -       0

---

> 199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0

 

 

root@unRAID:~# smartctl --all /dev/sda

smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WMAZA0651972

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

Local Time is:    Sat Jan  1 13:00:02 2011 EST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x82) Offline data collection activity

was completed without error.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (37080) seconds.

Offline data collection

capabilities: (0x7b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: (  2) minutes.

Extended self-test routine

recommended polling time: ( 255) minutes.

Conveyance self-test routine

recommended polling time: (  5) minutes.

SCT capabilities:       (0x3035) SCT Status supported.

SCT Feature Control supported.

SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0

  3 Spin_Up_Time            0x0027  162  162  021    Pre-fail  Always      -      6900

  4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      11

  5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

  7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

  9 Power_On_Hours          0x0032  100  100  000    Old_age  Always      -      43

10 Spin_Retry_Count        0x0032  100  253  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  253  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      8

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      7

193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      15

194 Temperature_Celsius    0x0022  125  120  000    Old_age  Always      -      25

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  200  200  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  200  200  000    Old_age  Offline      -      0

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 

============================================================================

==

== Disk /dev/sdb has been successfully precleared

==

============================================================================

S.M.A.R.T. error count differences detected after pre-clear

note, some 'raw' values may change, but not be an indication of a problem

54c54

<   1 Raw_Read_Error_Rate     0x002f   100   253   051    Pre-fail  Always       -       0

---

>   1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0

63c63

< 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       8

---

> 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       9

67c67

< 199 UDMA_CRC_Error_Count    0x0032   200   253   000    Old_age   Always       -       0

---

> 199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0

============================================================================

 

root@unRAID:~# smartctl --all /dev/sdb

smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WCAZA1111289

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

Local Time is:    Sat Jan  1 13:00:50 2011 EST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x82) Offline data collection activity

was completed without error.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (37200) seconds.

Offline data collection

capabilities: (0x7b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: (  2) minutes.

Extended self-test routine

recommended polling time: ( 255) minutes.

Conveyance self-test routine

recommended polling time: (  5) minutes.

SCT capabilities:       (0x3035) SCT Status supported.

SCT Feature Control supported.

SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0

  3 Spin_Up_Time            0x0027  165  165  021    Pre-fail  Always      -      6708

  4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      10

  5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

  7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

  9 Power_On_Hours          0x0032  100  100  000    Old_age  Always      -      43

10 Spin_Retry_Count        0x0032  100  253  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  253  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      8

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      7

193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      11

194 Temperature_Celsius    0x0022  124  120  000    Old_age  Always      -      26

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  200  200  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  200  200  000    Old_age  Offline      -      0

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 

============================================================================

==

== Disk /dev/sdc has been successfully precleared

==

============================================================================

S.M.A.R.T. error count differences detected after pre-clear

note, some 'raw' values may change, but not be an indication of a problem

19,20c19,20

< Offline data collection status:  (0x80)       Offline data collection activity

<                                       was never started.

---

> Offline data collection status:  (0x84)       Offline data collection activity

>                                       was suspended by an interrupting command from host.

54c54

<   1 Raw_Read_Error_Rate     0x002f   100   253   051    Pre-fail  Always       -       0

---

>   1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0

58c58

<   7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0

---

>   7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0

63c63

< 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       9

---

> 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       10

67c67

< 199 UDMA_CRC_Error_Count    0x0032   200   253   000    Old_age   Always       -       0

---

> 199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0

============================================================================

 

root@unRAID:~# smartctl --all /dev/sdc

smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WMAZA0987158

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

Local Time is:    Sat Jan  1 13:01:17 2011 EST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x82) Offline data collection activity

was completed without error.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: (36960) seconds.

Offline data collection

capabilities: (0x7b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: (  2) minutes.

Extended self-test routine

recommended polling time: ( 255) minutes.

Conveyance self-test routine

recommended polling time: (  5) minutes.

SCT capabilities:       (0x3035) SCT Status supported.

SCT Feature Control supported.

SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0

  3 Spin_Up_Time            0x0027  170  170  021    Pre-fail  Always      -      6466

  4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      11

  5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

  7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

  9 Power_On_Hours          0x0032  100  100  000    Old_age  Always      -      43

10 Spin_Retry_Count        0x0032  100  253  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  253  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      8

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      7

193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      13

194 Temperature_Celsius    0x0022  125  120  000    Old_age  Always      -      25

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  200  200  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  200  200  000    Old_age  Offline      -      2

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

 

These are brand new WD20EARS drives jumpered.

Link to comment
How do my 3 drives look?
We cannot tell by what you posted other than the reports say the disks were successfully pre-cleared.

 

The output from the pre-clear was the difference, as reported by the Linux "diff" command, between the smart report taken at the beginning of the pre-clear process and the one taken at the end.

 

What your printouts you show are the factory initial values of 253 being replace by a new starting point of 200. 

This is normal for almost all drives and brands (some start at 200, some parameters start at 100)

 

Since we only see differences, we have no way to know if a parameter was failing initially and is still failing in exactly the same way. (it would not be different, but identically failing, so not show in the "diff" output)  As far as we can see, all looks fine.

 

Joe L.

Link to comment

I just got done running preclear on 6 drives, 4 of them are the dreaded 4k Samsungs and they do all have a line that makes me scared. Has anyone seen this? Any thoughts?

 

Here is the line from one of the drives, the complete file is attached.

 

181 Program_Fail_Cnt_Total  0x0022   100   100   000    Old_age   Always       -       6374852

 

Thanks Jesse

 

That line says that

The current normalized value is 100

The worst normalized value ever was 100

The failure threshold is 0

The current value is the initial value (initialized value) from the manufacturer.  It has not moved from the initial value.

Since the current value is not equal to or less than the failure threshold, this SMART parameter has not failed.

 

The raw value has meaning only to the manufacturer, and they are not telling how to interpret it.

 

Sorry to tell you this, but you were scared only because you've not yet learned how to read a smart report.  There is nothing wrong with that parameter.

 

Joe L.

Link to comment

I am getting similar results (after 45 hours) like this on a WD Green 2TB drive (no jumpers)

 

===========================================================================
=                unRAID server Pre-Clear disk /dev/sdb
=                       cycle 1 of 1
= Disk Pre-Clear-Read completed                                 DONE
= Step 1 of 10 - Copying zeros to first 2048k bytes             DONE
= Step 2 of 10 - Copying zeros to remainder of disk to clear it DONE
= Step 3 of 10 - Disk is now cleared from MBR onward.           DONE
= Step 4 of 10 - Clearing MBR bytes for partition 2,3 & 4       DONE
= Step 5 of 10 - Clearing MBR code area                         DONE
= Step 6 of 10 - Setting MBR signature bytes                    DONE
= Step 7 of 10 - Setting partition 1 to precleared state        DONE
= Step 8 of 10 - Notifying kernel we changed the partitioning   DONE
= Step 9 of 10 - Creating the /dev/disk/by* entries             DONE
= Step 10 of 10 - Testing if the clear has been successful.     DONE
=
Disk Temperature: 32C, Elapsed Time:  10:32:36
============================================================================
==
== SORRY: Disk /dev/sdb MBR could NOT be precleared
==
== out4= 00092
== out5= 00092
============================================================================
1+0 records in
1+0 records out
512 bytes (512 B) copied, 0.000245285 s, 2.1 MB/s
0000000 0000 0000 0000 0000 0000 0000 0000 0000
*
0000700 0000 0000 0000 003f 0000 7af1 aea8 0000
0000720 0000 0000 0000 0000 0000 0000 0000 0000
*
0000760 0000 0000 0000 0000 0000 0000 0000 5c5c
0001000

 

The difference is that I get out4= 00000 and out5= 00000, 0+0 records in & out, 0 bytes copied.

 

I tried some commands and got a script error...

root@Tower:/boot/config# ./preclear_disk.sh -v         
./preclear_disk.sh version: .9.8

root@Tower:/boot/config# ./preclear_disk.sh -t /dev/sda
Pre-Clear unRAID Disk
########################################################################
########################################################################
./preclear_disk.sh: line 825: [: too many arguments
============================================================================
==
== Disk /dev/sda is NOT precleared
==
============================================================================

 

I was running this pre-clear at the same time as other disks.

Should I try again by itself?  Is there a way to bypass *all* the tests?

 

BTW, I did not jumper it because I am setting things up to get ready for 5.0b3 to support these WD Green drives.

 

Link to comment

I am getting similar results (after 45 hours) like this on a WD Green 2TB drive (no jumpers)

 

===========================================================================
=                unRAID server Pre-Clear disk /dev/sdb
=                       cycle 1 of 1
= Disk Pre-Clear-Read completed                                 DONE
= Step 1 of 10 - Copying zeros to first 2048k bytes             DONE
= Step 2 of 10 - Copying zeros to remainder of disk to clear it DONE
= Step 3 of 10 - Disk is now cleared from MBR onward.           DONE
= Step 4 of 10 - Clearing MBR bytes for partition 2,3 & 4       DONE
= Step 5 of 10 - Clearing MBR code area                         DONE
= Step 6 of 10 - Setting MBR signature bytes                    DONE
= Step 7 of 10 - Setting partition 1 to precleared state        DONE
= Step 8 of 10 - Notifying kernel we changed the partitioning   DONE
= Step 9 of 10 - Creating the /dev/disk/by* entries             DONE
= Step 10 of 10 - Testing if the clear has been successful.     DONE
=
Disk Temperature: 32C, Elapsed Time:  10:32:36
============================================================================
==
== SORRY: Disk /dev/sdb MBR could NOT be precleared
==
== out4= 00092
== out5= 00092
============================================================================
1+0 records in
1+0 records out
512 bytes (512 B) copied, 0.000245285 s, 2.1 MB/s
0000000 0000 0000 0000 0000 0000 0000 0000 0000
*
0000700 0000 0000 0000 003f 0000 7af1 aea8 0000
0000720 0000 0000 0000 0000 0000 0000 0000 0000
*
0000760 0000 0000 0000 0000 0000 0000 0000 5c5c
0001000

 

The difference is that I get out4= 00000 and out5= 00000, 0+0 records in & out, 0 bytes copied.

 

I tried some commands and got a script error...

root@Tower:/boot/config# ./preclear_disk.sh -v         
./preclear_disk.sh version: .9.8

root@Tower:/boot/config# ./preclear_disk.sh -t /dev/sda
Pre-Clear unRAID Disk
########################################################################
########################################################################
./preclear_disk.sh: line 825: [: too many arguments
============================================================================
==
== Disk /dev/sda is NOT precleared
==
============================================================================

 

I was running this pre-clear at the same time as other disks.

Should I try again by itself?  Is there a way to bypass *all* the tests?

 

BTW, I did not jumper it because I am setting things up to get ready for 5.0b3 to support these WD Green drives.

 

Yes, the drive has stopped responding.  (and the script was not coded to deal with that very elegantly)

 

Most people find they'll need to power cycle the drive to get it to respond again.

Even after that, many have had to clear the first few sectors to get it to respond sanely after changing the jumper (or adding it after the drive has been used without it being installed)

 

Basically, we've found it does not even respond to anything when locked up.  Not even an

fdisk -l /dev/sdb

will get complete results until you power cycle.

 

As far as skipping "tests" sorry... can't unless you don't want to clear the drive and ensure it is cleared.

Joe L.

Link to comment

Looks like you're right about that, 'fdisk -l' no longer shows sda.

I'll reboot once the other drive is done with preclear'ing.

When I wrote the script I never anticipated a disk would simply stop responding.  My newer version of preclear_disk.sh should handle it better.  (It won't make the disk respond, but it will exit more cleanly when the disk does not respond.  Would you like to give it a try?  I can zip it up and put attach it for a quick test.  You are perfect for the test, since you have a disk that is not responding right now.)

 

Joe L.

Link to comment

Here's some results from a 1TB Seagate, not sure what to make of the "Raw_Read_Error_Rate"

root@Tower:/tmp# diff smart_start2036 smart_finish2036 |more
54c54
<   1 Raw_Read_Error_Rate     0x000f   117   099   006    Pre-fail  Always       -       143105661
---
>   1 Raw_Read_Error_Rate     0x000f   114   099   006    Pre-fail  Always       -       78689498
58c58
<   7 Seek_Error_Rate         0x000f   075   060   030    Pre-fail  Always       -       36206913
---
>   7 Seek_Error_Rate         0x000f   075   060   030    Pre-fail  Always       -       36319190

 

And running smartctl --all /dev/sdd gives

User Capacity:    1,000,204,886,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Wed Jan  5 00:26:03 2011 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
...
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   114   099   006    Pre-fail  Always       -       78711073
  3 Spin_Up_Time            0x0003   100   100   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       101
  5 Reallocated_Sector_Ct   0x0033   095   095   036    Pre-fail  Always       -       216
  7 Seek_Error_Rate         0x000f   075   060   030    Pre-fail  Always       -       36349186
  9 Power_On_Hours          0x0032   089   089   000    Old_age   Always       -       9676
10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   100   037   020    Old_age   Always       -       101
...
SMART Error Log Version: 1
No Errors Logged
...

 

There are a lot of Raw_Read_Error_Rate however it went down?

 

Link to comment

 

5 Reallocated_Sector_Ct   0x0033   095   095   036    Pre-fail  Always       -       216

 

There are a lot of Raw_Read_Error_Rate however it went down?

 

The reallocated sector count at 216 is a definite problem.

 

It is encouraging that you were able to preclear the disk without the count increasing!  Otherwise the difference would have been highlighted by the preclear output.  But I have never seen a drive with more than 1 or 2 reallocated sectors that didn't continue to degrade with each parity check (although I've read reports of people with over 100 that have held steady).

 

If this disk were in the array, I would suggest that you run a parity verify (read only parity check) and see if the 216 number holds steady.  If it did, I would suggest running another one.  If you could run 3 in a row and not have the number increase, maybe the drive is okay. 

 

But since you are in the preclear stage, you might want to run it through 3 preclear cycles.  If the number holds steady, I'd consider trusting the disk.  But it would be a world's record of most reallocated sectors on a stable disk from all the smart output I've seen!

 

The other attribute to monitor closely is the current_pending_sector.  This is the number of sectors that have been flagged to be reallocated.  You did not post this value.

 

The "raw read error rate" is nothing to be overly concerned about unless and until you start to get close to the threshold for failure.  And you are no where close.

 

This is a good example of where the diff list of pre-preclear smart output and post-preclear smart output is not sufficient to identify all problems.

Link to comment

hello everyone,

 

sorry to bother.

I thought I could figure it out by myself.

but I am not sure.

 

== Disk /dev/sde has been successfully precleared
==
============================================================================
S.M.A.R.T. error count differences detected after pre-clear
note, some 'raw' values may change, but not be an indication of a problem
54c54
<   1 Raw_Read_Error_Rate     0x000f   100   100   006    Pre-fail  Always       -       9525
---
>   1 Raw_Read_Error_Rate     0x000f   109   100   006    Pre-fail  Always       -       21790999
58c58
<   7 Seek_Error_Rate         0x000f   100   253   030    Pre-fail  Always       -       28
---
>   7 Seek_Error_Rate         0x000f   100   253   030    Pre-fail  Always       -       156494
64c64
< 188 Command_Timeout         0x0032   100   253   000    Old_age   Always       -       0
---
> 188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
66,67c66,67
< 190 Airflow_Temperature_Cel 0x0022   070   070   045    Old_age   Always       -       30 (Lifetime Min/Max 29/30)
< 195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always
---
> 190 Airflow_Temperature_Cel 0x0022   064   064   045    Old_age   Always       -       36 (Lifetime Min/Max 29/36)
> 195 Hardware_ECC_Recovered  0x001a   051   047   000    Old_age   Always
70,73c70,73
< 199 UDMA_CRC_Error_Count    0x003e   200   253   000    Old_age   Always       -       0
< 240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       193269233352719
< 241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       0
< 242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       1716
---
> 199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
> 240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       121027883434026
> 241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       3906582512
> 242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       3693395106
============================================================================

 

if someone could strip it down for me it would be awesome.

I have a bunch of disk I am pre-clearing..

so if you could explain your findings I will try to learn from it.

 

here is what I am understanding (I am sorry if I show some ignorance.), I reformatted it to make it easier to read.

 

first rule is to ignore the raw value changes (I think... lol)

< ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
<   1 Raw_Read_Error_Rate     0x000f   100   100   006    Pre-fail  Always       -       9525
>   1 Raw_Read_Error_Rate     0x000f   109   100   006    Pre-fail  Always       -       21790999
value going away from the treshold.. so positive


<   7 Seek_Error_Rate         0x000f   100   253   030    Pre-fail  Always       -       28
>   7 Seek_Error_Rate         0x000f   100   253   030    Pre-fail  Always       -       156494
ignored as per the "first rule"


< 188 Command_Timeout         0x0032   100   253   000    Old_age   Always       -       0
> 188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
worst going toward the threshold.. but I do not know how to analyse that..


< 190 Airflow_Temperature_Cel 0x0022   070   070   045    Old_age   Always       -       30 (Lifetime Min/Max 29/30)
> 190 Airflow_Temperature_Cel 0x0022   064   064   045    Old_age   Always       -       36 (Lifetime Min/Max 29/36)
kinda normal that the temp changes during a preclear


< 195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always
> 195 Hardware_ECC_Recovered  0x001a   051   047   000    Old_age   Always
value change, worst change, both are going toward the threshold. shouldn't I be worried ?


< 199 UDMA_CRC_Error_Count    0x003e   200   253   000    Old_age   Always       -       0
> 199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
worst going toward the threshold. shouldn't I be worried ?


< 240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       193269233352719
> 240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       121027883434026
ignored as per the "first rule"


< 241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       0
> 241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       3906582512
ignored as per the "first rule"


< 242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       1716
> 242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       3693395106
ignored as per the "first rule"

 

any help is welcome,

 

R

 

Link to comment

redia -

 

Looks good.  Of course, this is only showing the difference between the smart report before doing the preclear, and the smart report after doing the preclear.  If the disk had a serous problem before you started and didn't get worse in the preclear, this would not show it.

Link to comment

Just finished my first 2TB WDEars and received this email second one about to finish does this one look good?

 

== Disk /dev/sda has been successfully precleared

==

== Ran 1 preclear-disk cycle

==

== Using :Read block size = 8225280 Bytes

== Last Cycle's Pre Read Time  : 7:38:20 (72 MB/s)

== Last Cycle's Zeroing time  : 7:37:00 (72 MB/s)

== Last Cycle's Post Read Time : 14:00:03 (39 MB/s)

== Last Cycle's Total Time    : 29:16:31

==

== Total Elapsed Time 29:16:31

==

== Disk Start Temperature: 20C

==

== Current Disk Temperature: 24C,

==

============================================================================

S.M.A.R.T. error count differences detected after pre-clear

note, some 'raw' values may change, but not be an indication of a problem

19,20c19,20

< Offline data collection status:  (0x80)      Offline data collection activity

<                                      was never started.

---

> Offline data collection status:  (0x84)      Offline data collection activity

>                                      was suspended by an interrupting command from host.

54c54

<  1 Raw_Read_Error_Rate    0x002f  100  253  051    Pre-fail  Always      -      0

---

>  1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0

58c58

<  7 Seek_Error_Rate        0x002e  100  253  000    Old_age  Always      -      0

---

>  7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

63c63

< 193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      12

---

> 193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      13

67c67

< 199 UDMA_CRC_Error_Count    0x0032  200  253  000    Old_age  Always      -      0

---

> 199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

============================================================================

============================================================================

==

== S.M.A.R.T Initial Report

==

smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WMAZA1096388

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x80) Offline data collection activity

                                      was never started.

                                      Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

                                      without error or no self-test has ever

                                      been run.

Total time to complete Offline

data collection:                (38760) seconds.

Offline data collection

capabilities:                    (0x7b) SMART execute Offline immediate.

                                      Auto Offline data collection on/off support.

                                      Suspend Offline collection upon new

                                      command.

                                      Offline surface scan supported.

                                      Self-test supported.

                                      Conveyance Self-test supported.

                                      Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

                                      power-saving mode.

                                      Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

                                      General Purpose Logging supported.

Short self-test routine

recommended polling time:        (  2) minutes.

Extended self-test routine

recommended polling time:        ( 255) minutes.

Conveyance self-test routine

recommended polling time:        (  5) minutes.

SCT capabilities:              (0x3035) SCT Status supported.

                                      SCT Feature Control supported.

                                      SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate    0x002f  100  253  051    Pre-fail  Always      -      0

3 Spin_Up_Time            0x0027  100  253  021    Pre-fail  Always      -      0

4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      3

5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

7 Seek_Error_Rate        0x002e  100  253  000    Old_age  Always      -      0

10 Spin_Retry_Count        0x0032  100  253  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  253  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      2

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      1

193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      12

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  100  253  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  253  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  100  253  000    Old_age  Offline      -      0

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

  1        0        0  Not_testing

  2        0        0  Not_testing

  3        0        0  Not_testing

  4        0        0  Not_testing

  5        0        0  Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

==

============================================================================

 

 

 

============================================================================

==

== S.M.A.R.T Final Report

==

smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WMAZA1096388

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x84) Offline data collection activity

                                      was suspended by an interrupting command from host.

                                      Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

                                      without error or no self-test has ever

                                      been run.

Total time to complete Offline

data collection:                (38760) seconds.

Offline data collection

capabilities:                    (0x7b) SMART execute Offline immediate.

                                      Auto Offline data collection on/off support.

                                      Suspend Offline collection upon new

                                      command.

                                      Offline surface scan supported.

                                      Self-test supported.

                                      Conveyance Self-test supported.

                                      Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

                                      power-saving mode.

                                      Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

                                      General Purpose Logging supported.

Short self-test routine

recommended polling time:        (  2) minutes.

Extended self-test routine

recommended polling time:        ( 255) minutes.

Conveyance self-test routine

recommended polling time:        (  5) minutes.

SCT capabilities:              (0x3035) SCT Status supported.

                                      SCT Feature Control supported.

                                      SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0

3 Spin_Up_Time            0x0027  100  253  021    Pre-fail  Always      -      0

4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      3

5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

10 Spin_Retry_Count        0x0032  100  253  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  253  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      2

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      1

193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      13

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  100  253  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  100  253  000    Old_age  Offline      -      0

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

  1        0        0  Not_testing

  2        0        0  Not_testing

  3        0        0  Not_testing

  4        0        0  Not_testing

  5        0        0  Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

Link to comment

This is my second drive thank you. new to unraid.

============================================================================

==

== Disk /dev/sdb has been successfully precleared

==

== Ran 1 preclear-disk cycle

==

== Using :Read block size = 8225280 Bytes

== Last Cycle's Pre Read Time  : 7:42:28 (72 MB/s)

== Last Cycle's Zeroing time  : 7:41:02 (72 MB/s)

== Last Cycle's Post Read Time : 14:07:33 (39 MB/s)

== Last Cycle's Total Time    : 29:33:51

==

== Total Elapsed Time 29:33:51

==

== Disk Start Temperature: 20C

==

== Current Disk Temperature: 23C,

==

============================================================================

S.M.A.R.T. error count differences detected after pre-clear

note, some 'raw' values may change, but not be an indication of a problem

19,20c19,20

< Offline data collection status:  (0x80)      Offline data collection activity

<                                      was never started.

---

> Offline data collection status:  (0x84)      Offline data collection activity

>                                      was suspended by an interrupting command from host.

54c54

<  1 Raw_Read_Error_Rate    0x002f  100  253  051    Pre-fail  Always      -      0

---

>  1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0

58c58

<  7 Seek_Error_Rate        0x002e  100  253  000    Old_age  Always      -      0

---

>  7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

63c63

< 193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      15

---

> 193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      17

67c67

< 199 UDMA_CRC_Error_Count    0x0032  200  253  000    Old_age  Always      -      0

---

> 199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

============================================================================

============================================================================

==

== S.M.A.R.T Initial Report

==

smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WMAZA1096534

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x80) Offline data collection activity

                                      was never started.

                                      Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

                                      without error or no self-test has ever

                                      been run.

Total time to complete Offline

data collection:                (38460) seconds.

Offline data collection

capabilities:                    (0x7b) SMART execute Offline immediate.

                                      Auto Offline data collection on/off support.

                                      Suspend Offline collection upon new

                                      command.

                                      Offline surface scan supported.

                                      Self-test supported.

                                      Conveyance Self-test supported.

                                      Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

                                      power-saving mode.

                                      Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

                                      General Purpose Logging supported.

Short self-test routine

recommended polling time:        (  2) minutes.

Extended self-test routine

recommended polling time:        ( 255) minutes.

Conveyance self-test routine

recommended polling time:        (  5) minutes.

SCT capabilities:              (0x3035) SCT Status supported.

                                      SCT Feature Control supported.

                                      SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate    0x002f  100  253  051    Pre-fail  Always      -      0

3 Spin_Up_Time            0x0027  174  174  021    Pre-fail  Always      -      6275

4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      10

5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

7 Seek_Error_Rate        0x002e  100  253  000    Old_age  Always      -      0

10 Spin_Retry_Count        0x0032  100  253  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  253  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      8

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      7

193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      15

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  100  253  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  253  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  100  253  000    Old_age  Offline      -      0

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

  1        0        0  Not_testing

  2        0        0  Not_testing

  3        0        0  Not_testing

  4        0        0  Not_testing

  5        0        0  Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

==

============================================================================

 

 

 

============================================================================

==

== S.M.A.R.T Final Report

==

smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)

Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

 

=== START OF INFORMATION SECTION ===

Device Model:    WDC WD20EARS-00MVWB0

Serial Number:    WD-WMAZA1096534

Firmware Version: 51.0AB51

User Capacity:    2,000,398,934,016 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  8

ATA Standard is:  Exact ATA specification draft version not indicated

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x84) Offline data collection activity

                                      was suspended by an interrupting command from host.

                                      Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

                                      without error or no self-test has ever

                                      been run.

Total time to complete Offline

data collection:                (38460) seconds.

Offline data collection

capabilities:                    (0x7b) SMART execute Offline immediate.

                                      Auto Offline data collection on/off support.

                                      Suspend Offline collection upon new

                                      command.

                                      Offline surface scan supported.

                                      Self-test supported.

                                      Conveyance Self-test supported.

                                      Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

                                      power-saving mode.

                                      Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

                                      General Purpose Logging supported.

Short self-test routine

recommended polling time:        (  2) minutes.

Extended self-test routine

recommended polling time:        ( 255) minutes.

Conveyance self-test routine

recommended polling time:        (  5) minutes.

SCT capabilities:              (0x3035) SCT Status supported.

                                      SCT Feature Control supported.

                                      SCT Data Table supported.

 

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate    0x002f  200  200  051    Pre-fail  Always      -      0

3 Spin_Up_Time            0x0027  174  174  021    Pre-fail  Always      -      6275

4 Start_Stop_Count        0x0032  100  100  000    Old_age  Always      -      10

5 Reallocated_Sector_Ct  0x0033  200  200  140    Pre-fail  Always      -      0

7 Seek_Error_Rate        0x002e  200  200  000    Old_age  Always      -      0

10 Spin_Retry_Count        0x0032  100  253  000    Old_age  Always      -      0

11 Calibration_Retry_Count 0x0032  100  253  000    Old_age  Always      -      0

12 Power_Cycle_Count      0x0032  100  100  000    Old_age  Always      -      8

192 Power-Off_Retract_Count 0x0032  200  200  000    Old_age  Always      -      7

193 Load_Cycle_Count        0x0032  200  200  000    Old_age  Always      -      17

196 Reallocated_Event_Count 0x0032  200  200  000    Old_age  Always      -      0

197 Current_Pending_Sector  0x0032  200  200  000    Old_age  Always      -      0

198 Offline_Uncorrectable  0x0030  100  253  000    Old_age  Offline      -      0

199 UDMA_CRC_Error_Count    0x0032  200  200  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0008  100  253  000    Old_age  Offline      -      0

 

SMART Error Log Version: 1

No Errors Logged

 

SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]

 

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

  1        0        0  Not_testing

  2        0        0  Not_testing

  3        0        0  Not_testing

  4        0        0  Not_testing

  5        0        0  Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

==

============================================================================

 

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.