upthetoon Posted October 2, 2015 Share Posted October 2, 2015 Hi, Aa few apps were wonky this morning so I rebooted by server. It's come back up with the partiy drive marked as Faulty. This is the yongest drive in my array so I hope its not goosed. I'm going to get the server out and re-seat the connections but can anyone see anything telling in the attached diagnostics? Cheers. ridcully-diagnostics-20151002-1626.zip Quote Link to comment
upthetoon Posted October 2, 2015 Author Share Posted October 2, 2015 Report of the offending drive smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.1.7-unRAID] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: HGST HDN724040ALE640 Serial Number: PK1334PBH0G3LS LU WWN Device Id: 5 000cca 23dce4c7e Firmware Version: MJAOA5E0 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Oct 2 16:26:17 2015 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 24) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 587) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 137 137 054 Pre-fail Offline - 77 3 Spin_Up_Time 0x0007 131 131 024 Pre-fail Always - 592 (Average 591) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 849 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 121 121 020 Pre-fail Offline - 34 9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 11209 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 34 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 855 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 855 194 Temperature_Celsius 0x0002 162 162 000 Old_age Always - 37 (Min/Max 13/44) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 11209 - # 2 Extended offline Aborted by host 50% 11203 - # 3 Short offline Aborted by host 90% 9964 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Quote Link to comment
upthetoon Posted October 2, 2015 Author Share Posted October 2, 2015 Everything seems fine connection wise. No change when I booted back up. I can't actually see any errors or issues in the syslog. Quote Link to comment
itimpi Posted October 2, 2015 Share Posted October 2, 2015 Once the parity drive has been reported as faulty it will not get reset to good until you have successfully rebuilt parity. The steps to achieve this are: Stop array and Unassign Parity disk Start array with parity disk unassigned. This makes unRAID 'forget' the current parity disk Stop the array and reassign the parity disk Start the array to build parity from the data disks. When the parity build completes it is a good idea to do a parity check to confirm that parity was written correctly. This should report 0 errors. Quote Link to comment
upthetoon Posted October 2, 2015 Author Share Posted October 2, 2015 Once the parity drive has been reported as faulty it will not get reset yo good until you have successfully rebuilt parity. The steps to achieve this are: Stop array and Unassign Parity disk Start array with parity disk unassigned. This makes unRAID 'forget' the current parity disk Stop the array and reassign the parity disk Start the array to build parity from the data disks. When the parity build completes it is a good idea to do a parity check to confirm that parity was written correctly. This should report 0 errors. Thanks! It's building the parity again now. Fingers crossed it won't happen again... Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.