bungee91 Posted October 20, 2015 Share Posted October 20, 2015 I get these messages a LOT in my system log, which looks to be for two specific usb devices, 1-3 and 1-4. These are both Gyration remotes that I use for HTPC usage. I believe I have seen the same messages for other USB devices that I have had attached. I attempted to make some changes for USB settings in the BIOS (newest version) hoping that it would help, however nothing seemed to matter. I don't have many options to change, and if I remove the legacy USB support it would either not boot unRAID, or did something very odd and had write errors to my boot flash drive. They don't seem to cause any issues, but my log is littered with them. I have not tried the new nec-xhci method in the XML, maybe it will help with this. Oct 19 20:42:12 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:12 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:12 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:13 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:14 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:14 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:15 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:15 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:15 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:16 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:17 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:17 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:17 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:17 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:17 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:21 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:21 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:21 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:22 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:22 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:22 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:24 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:24 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:24 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:25 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:25 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:25 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:26 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:26 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:26 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:26 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:42:27 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:42:27 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:43:35 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:43:35 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:43:35 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:43:35 Server kernel: br0: port 2(vnet0) entered disabled state Oct 19 20:43:35 Server avahi-daemon[9227]: Withdrawing workstation service for vnet0. Oct 19 20:43:35 Server kernel: device vnet0 left promiscuous mode Oct 19 20:43:35 Server kernel: br0: port 2(vnet0) entered disabled state Oct 19 20:43:35 Server kernel: input: Gyration Gyration RF Technology Receiver as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:0C16:0008.0013/input/input23 Oct 19 20:43:35 Server kernel: gyration 0003:0C16:0008.0013: input,hiddev0,hidraw3: USB HID v1.10 Keyboard [Gyration Gyration RF Technology Receiver] on usb-0000:00:14.0-3/input0 Oct 19 20:43:35 Server kernel: input: Gyration Gyration RF Technology Receiver as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.1/0003:0C16:0008.0014/input/input24 Oct 19 20:43:35 Server kernel: gyration 0003:0C16:0008.0014: input,hiddev0,hidraw4: USB HID v1.20 Mouse [Gyration Gyration RF Technology Receiver] on usb-0000:00:14.0-3/input1 Oct 19 20:44:22 Server kernel: device vnet0 entered promiscuous mode Oct 19 20:44:22 Server kernel: br0: topology change detected, sending tcn bpdu Oct 19 20:44:22 Server kernel: br0: port 2(vnet0) entered forwarding state Oct 19 20:44:22 Server kernel: br0: port 2(vnet0) entered forwarding state Oct 19 20:44:23 Server kernel: vfio_ecap_init: 0000:02:00.0 hiding ecap 0x19@0x900 Oct 19 20:44:25 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:26 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:26 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:26 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:26 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:26 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:26 Server kernel: kvm: zapping shadow pages for mmio generation wraparound Oct 19 20:44:30 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:31 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:31 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:31 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:31 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:31 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:33 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:33 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:33 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:34 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:34 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:34 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:35 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:35 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:35 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:35 Server kernel: usb 1-3: reset low-speed USB device number 2 using xhci_hcd Oct 19 20:44:36 Server kernel: usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:44:36 Server kernel: usb 1-3: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:45:47 Server kernel: usb 1-4: USB disconnect, device number 9 Oct 19 20:45:53 Server kernel: usb 1-4: new high-speed USB device number 10 using xhci_hcd Oct 19 20:45:53 Server kernel: hub 1-4:1.0: USB hub found Oct 19 20:45:53 Server kernel: hub 1-4:1.0: 4 ports detected Oct 19 20:47:10 Server kernel: usb 1-4.1: new low-speed USB device number 11 using xhci_hcd Oct 19 20:47:10 Server kernel: usb 1-4.1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes Oct 19 20:47:10 Server kernel: usb 1-4.1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes Log attached (it is cutoff as the logfile ran out of space, and I increased it's allowed size). The options I have in my BIOS are as follows (with descriptions), I am not certain what they are set to at the moment, I believe they are all default values: Intel USB 3.0 Mode - Select Intel® USB 3.0 controller mode. Set [smart Auto] to keep the USB 3.0 driver enabled ater rebooting (USB 3.0 is enabled in BIOS). Set [Auto] to automatically enable the USB 3.0 driver ater entering the OS (USB 3.0 is disabled in BIOS). Set [Enabled] to keep the USB 3.0 driver enabled (Must install driver to use USB devices under Windows® 7). Set [Disabled] to disable the USB 3.0 ports. Legacy USB Support - Enable or disable Legacy OS Support for USB 2.0 devices. If you encounter USB compatibility issues it is recommended to disable legacy USB support. Select UEFI Setup Only to support USB devices under the UEFI setup and Windows/Linux operating systems only. Legacy USB 3.0 Support - Enable or disable Legacy OS Support for USB 3.0 devices. If you encounter USB compatibility issues it is recommended to disable legacy USB support. Select UEFI Setup Only to support USB devices under the UEFI setup and Windows/Linux operating systems only. USB Compatibility Patch - If your USB devices (i.e. USB mouse or storage) encounter compatibility problems, please enable this option to ix it. Please note that ater enabling this option, it is normal that the system will postpone booting up ater pressing the power button. Third Party USB 3.0 Controller Enable or disable all of the USB 3.0 ports controlled by hird Party chips. syslog.txt Quote Link to comment
bungee91 Posted October 23, 2015 Author Share Posted October 23, 2015 No one else has had this occur? Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.