[Support] binhex - DelugeVPN


8747 posts in this topic Last Reply

Recommended Posts

15 hours ago, Roudy said:

 

Sorry, I think I missed the two connections part, my apologies! I'm a network engineer by trade, so I wanted to help if I could.

 

 

Because you are routing Sonarr and Radarr through the docker container itself, you will not need the proxy settings enabled, as all traffic goes over the DelugeVPN tunnel now. You should uncheck that box for both Sonarr and Radarr because it is now redundant. 

thanks again,  this resolved the issue again.

 

Link to post
  • Replies 8.7k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Popular Posts

OK guys, multi remote endpoint support is now in for this image please pull down the new image (this change will be rolled out to all my vpn images shortly).   What this means is that the im

There has been an issue raised on GitHub related to tracker announce request IP leakage under certain circumstances, after careful review of iptables i have tightened up the rules to prevent this. A n

I wanted to summarize how I got Mullvad working with DelugeVPN as I had to piece together several "solutions" from different comments in this thread and there was some incorrect info; likely old.

Posted Images

18 hours ago, Roudy said:

@xhonestly Are your Radarr and Sonarr connected through Deluge Docker or just using it as a Proxy?

I have my set up based on spacedinvader's video to set up sonarr and radarr to use the VPN in the deluge docker via privoxy. I had it set up with openvpn but at some point that stopped working and I switched to wireguard.

 

Edit: Just got Deluge web UI back. Had a typo in the LAN_NETWORK. It defaults to xxx.xxx.1.0/24 and mine needed to be xxx.xxx.0.0/24

Edited by xhonestly
Link to post
On 4/9/2021 at 11:25 AM, xhonestly said:

I have my set up based on spacedinvader's video to set up sonarr and radarr to use the VPN in the deluge docker via privoxy. I had it set up with openvpn but at some point that stopped working and I switched to wireguard.

 

Edit: Just got Deluge web UI back. Had a typo in the LAN_NETWORK. It defaults to xxx.xxx.1.0/24 and mine needed to be xxx.xxx.0.0/24

Man I'm glad I went to the end of this thread that Google took me to. This worked for me to get the UI up and responsive.

Link to post

Hello. I can't seem to make Deluge check my files. The files are there, the paths are correct but instead of using the existing files, it starts downloading them again. Any suggestions on how I might remedy this? Thank you in advance.

Link to post

I am having issues accessing the webui when I set VPN_ENABLE to yes. I had this setup running just fine, now I am trying to install it on a new device using the same Openvpn file and credentials but it wont work on the new device. On the logs it says that the connection was established. I am using a Synology NAS DS218+.

 

Here is the end of my DelugeVPN log

 

2021-04-11 02:14:23,572 DEBG 'start-script' stdout output:

2021-04-11 02:14:23 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1633', remote='link-mtu 1581'

2021-04-11 02:14:23 WARNING: 'auth' is used inconsistently, local='auth SHA512', remote='auth [null-digest]'

2021-04-11 02:14:23 Control Channel: TLSv1.2, cipher TLSv1.2 ECDHE-RSA-AES256-GCM-SHA384, 2048 bit RSA

2021-04-11 02:14:23 [us-chi-v023.prod.surfshark.com] Peer Connection Initiated with [AF_INET]MY IP:1194

 

 

UPDATE: I fixed it by starting the container with root privileges which I don't necessarily want to do. anybody knows why it only works with root?

Edited by joelstitch
Link to post

I just upgraded Unraid from 6.8.3 to 6.9.1.

 

That's the only change I've made and now delugevpn gui won't load and the log is showing a few errors which I've searched through here but can't seem to find a solution that applies to me.

 

2021-04-11 11:15:37,734 DEBG 'start-script' stderr output:
parse error: Invalid numeric literal at line 4, column 0

2021-04-11 11:15:37,931 DEBG 'start-script' stderr output:
parse error: Invalid numeric literal at line 1, column 7

2021-04-11 11:15:37,932 DEBG 'start-script' stdout output:
[warn] Unable to successfully download PIA json to generate token from URL 'https://199.36.223.130/authv3/generateToken'
[info] Retrying in 10 secs...

 

attached is my salted debug log

supervisord (salted).txt

Edited by TBoneStaek
failed upload
Link to post

Hello there! I've used the image for quite some time and it worked like a charm. But after Docker Desktop (Mac OS) update to 3.3.0 (62916) the logs are like this:
 

2021-04-11 21:34:34,395 DEBG 'start-script' stdout output:
--------------------
2021-04-11 21:34:34,399 DEBG 'start-script' stdout output:
[info] Attempting to bring WireGuard interface 'up'...
2021-04-11 21:34:34,411 DEBG 'start-script' stderr output:
Warning: `/config/wireguard/wg0.conf' is world accessible
2021-04-11 21:34:34,418 DEBG 'start-script' stderr output:
[#] ip link add wg0 type wireguard
2021-04-11 21:34:34,420 DEBG 'start-script' stderr output:
Error: Unknown device type.
2021-04-11 21:34:34,423 DEBG 'start-script' stderr output:
Unable to access interface: Protocol not supported
2021-04-11 21:34:34,423 DEBG 'start-script' stderr output:
[#] ip link delete dev wg0
2021-04-11 21:34:34,427 DEBG 'start-script' stderr output:
Cannot find device "wg0"
2021-04-11 21:34:34,428 DEBG 'start-script' stdout output:
[warn] WireGuard interface failed to come 'up', exit code is '1'

 

The "config/wireguard/wg0.conf" is like that:

[Interface]
PostUp = '/root/wireguardup.sh'
PostDown = '/root/wireguarddown.sh'
Address = ???.???.???.???/24
DNS = ???.???.???.???, ???.???.???.???
PrivateKey = ???

[Peer]
PublicKey = ???
PresharedKey = ???
AllowedIPs = 0.0.0.0/0
Endpoint = ???.???.???.???:???
PersistentKeepalive = 25

(of course there are real values instead of ???)

 

Any ideas on how to fix that or what to look for in the logs?

Link to post
7 hours ago, booppy said:

Hello there! I've used the image for quite some time and it worked like a charm. But after Docker Desktop (Mac OS) update to 3.3.0 (62916) the logs are like this:
 



2021-04-11 21:34:34,395 DEBG 'start-script' stdout output:
--------------------
2021-04-11 21:34:34,399 DEBG 'start-script' stdout output:
[info] Attempting to bring WireGuard interface 'up'...
2021-04-11 21:34:34,411 DEBG 'start-script' stderr output:
Warning: `/config/wireguard/wg0.conf' is world accessible
2021-04-11 21:34:34,418 DEBG 'start-script' stderr output:
[#] ip link add wg0 type wireguard
2021-04-11 21:34:34,420 DEBG 'start-script' stderr output:
Error: Unknown device type.
2021-04-11 21:34:34,423 DEBG 'start-script' stderr output:
Unable to access interface: Protocol not supported
2021-04-11 21:34:34,423 DEBG 'start-script' stderr output:
[#] ip link delete dev wg0
2021-04-11 21:34:34,427 DEBG 'start-script' stderr output:
Cannot find device "wg0"
2021-04-11 21:34:34,428 DEBG 'start-script' stdout output:
[warn] WireGuard interface failed to come 'up', exit code is '1'

 

The "config/wireguard/wg0.conf" is like that:



[Interface]
PostUp = '/root/wireguardup.sh'
PostDown = '/root/wireguarddown.sh'
Address = ???.???.???.???/24
DNS = ???.???.???.???, ???.???.???.???
PrivateKey = ???

[Peer]
PublicKey = ???
PresharedKey = ???
AllowedIPs = 0.0.0.0/0
Endpoint = ???.???.???.???:???
PersistentKeepalive = 25

(of course there are real values instead of ???)

 

Any ideas on how to fix that or what to look for in the logs?

Exact same thing happened to me.

Link to post
17 hours ago, TBoneStaek said:

I just upgraded Unraid from 6.8.3 to 6.9.1.

 

That's the only change I've made and now delugevpn gui won't load and the log is showing a few errors which I've searched through here but can't seem to find a solution that applies to me.

 

2021-04-11 11:15:37,734 DEBG 'start-script' stderr output:
parse error: Invalid numeric literal at line 4, column 0

2021-04-11 11:15:37,931 DEBG 'start-script' stderr output:
parse error: Invalid numeric literal at line 1, column 7

2021-04-11 11:15:37,932 DEBG 'start-script' stdout output:
[warn] Unable to successfully download PIA json to generate token from URL 'https://199.36.223.130/authv3/generateToken'
[info] Retrying in 10 secs...

 

attached is my salted debug log

supervisord (salted).txt 60 kB · 1 download

try a different endpoint, looks like a pia outage for ca-montreal.

Link to post

Hello since the last Unraid update.

I have an password error on webUI.

 

How is possible ?? My password is correct.

I use Bitwarden for this.

 

How change admin password without web UI?

 

(sorry for my english)

 

image.png.35115d8f888e28420aa5a25c39950fad.png

Link to post
30 minutes ago, thymon said:

Hello since the last Unraid update.

I have an password error on webUI.

 

How is possible ?? My password is correct.

I use Bitwarden for this.

 

How change admin password without web UI?

 

(sorry for my english)

 

image.png.35115d8f888e28420aa5a25c39950fad.png

Have you tried the default password incase it reset in the update? deluge is the default 

Link to post

For those with the startup script errors:

 

I just redownloaded a configuration file from PIA website, deleted the old one, and restarted Deluge and it seems to have fixed it. It looks to me that they renamed it to exclude the "nextgen-" from the file name. I don't know if that matters.

Link to post
8 minutes ago, LTM said:

For those with the startup script errors:

 

I just redownloaded a configuration file from PIA website, deleted the old one, and restarted Deluge and it seems to have fixed it. It looks to me that they renamed it to exclude the "nextgen-" from the file name. I don't know if that matters.

 

Do you have a link to the download?  I am assuming this is only if you are using the ovpn files and not using Wireguard?

Link to post
Quote

 

Updated Unraid to 6.9.2 this morning and this container will no longer work correctly. 

 




2021-04-12 09:33:16,216 DEBG 'start-script' stderr output:
parse error: Invalid numeric literal at line 4, column 0


2021-04-12 09:33:16,450 DEBG 'start-script' stderr output:
parse error: Invalid numeric literal at line 1, column 7


2021-04-12 09:33:16,451 DEBG 'start-script' stdout output:
[warn] Unable to successfully download PIA json to generate token from URL 'https://154.3.40.3/authv3/generateToken'
[info] Retrying in 10 secs...


I am using Wireguard+PIA.

Any ideas?

 

EDIT: Looks to be an issue with Canadian endpoints? Tried ca-montreal.privacy.network and ca-toronto.privacy.network with the same error, but Bahamas (bahamas.privacy.network) seems to work fine. 

Oddly, I can connect to both of the above Canadian endpoints just fine using my Windows client.

Edited by dcarpenter85
Link to post
33 minutes ago, dcarpenter85 said:

EDIT: Looks to be an issue with Canadian endpoints? Tried ca-montreal.privacy.network and ca-toronto.privacy.network with the same error, but Bahamas (bahamas.privacy.network) seems to work fine. 

Oddly, I can connect to both of the above Canadian endpoints just fine using my Windows client.

I've been okay with Toronto. Strange...

Link to post
1 minute ago, dcarpenter85 said:

But not 6.9.2 yet? My problems didn't start until I went from 6.9.1 to 6.9.2

Nope, not 6.9.2. I contemplated doing that today to see if that fixed it but... I imagine not. Must have been a coincidence though, again, I have Toronto working for me. Very strange.

Link to post

I seem to have an issue where my container is using the wrong IP to generate a PIA token?

 

2021-04-12 19:37:51,550 DEBG 'start-script' stdout output:
parse error: Invalid numeric literal at line 1, column 7


2021-04-12 19:37:51,551 DEBG 'start-script' stdout output:
[warn] Unable to successfully download PIA json to generate token from URL 'https://10.0.0.1/authv3/generateToken'

2021-04-12 19:37:51,551 DEBG 'start-script' stdout output:
[info] 12 retries left
[info] Retrying in 10 secs...

 

Link to post
On 4/10/2021 at 6:43 PM, Keek Uras said:

Hello. I can't seem to make Deluge check my files. The files are there, the paths are correct but instead of using the existing files, it starts downloading them again. Any suggestions on how I might remedy this? Thank you in advance.

 

Deluge doesn't really keep track of files, it just downloads what is sent to it. You may want to look at whatever you have sending downloads to Deluge. It sounds like it is losing track of the file once it is complete and it is thinking it failed and reinitiates the download again.

Link to post
On 4/12/2021 at 9:34 AM, dcarpenter85 said:

EDIT: Looks to be an issue with Canadian endpoints? Tried ca-montreal.privacy.network and ca-toronto.privacy.network with the same error, but Bahamas (bahamas.privacy.network) seems to work fine. 

Oddly, I can connect to both of the above Canadian endpoints just fine using my Windows client.

I was having issues connecting to Canadian endpoints as well, same error in the logs. Was able to connect to the Bahamas just fine. Not sure which version I was running before (should have checked) but I added :lastest to the containers Repository field and after pulling down the image I'm able to connect to Toronto again.

Link to post
2 hours ago, WishmastR said:

Also having the same issue with this container used with wireguard/pia after upgrade to 6.9.2

For those that managed to fix it which file did you download and where did you put it ?

For me it was simply adding " :latest " to the end of the repository line. I'm also using wireguard/pia connecting to Toronto.image.thumb.png.bba8006d24ad97d2d350d0436f681246.png

 

Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.