firetime Posted August 11, 2016 Share Posted August 11, 2016 (edited) Figured I should finally post pics of my build. Originally assembled the server September 2014, only took me until the server's 2nd birthday to take pictures. Original OS: Unraid 5.0.6 (I think) Current OS: Unraid 6.2.4 CPU: Intel Xeon E3-1220V3 Haswell 3.1GHz CPU Cooler: Noctua NH-L9i + Nexus 80mm or 92mm Fan Slot to 120mm Fan Converter + Cougar Vortex PWM 120 Cooling CF-V12HP Motherboard: ASRock E3C224D4I-14S RAM: Crucial 16GB (2 x 8GB) Case: LIAN LI PC-Q25B Power Supply: SILVERSTONE ST45SF-G 450W SFX (died) CORSAIR SF450 450W Fans: Cougar CF-V14HP 140mm & COUGAR CF-V12HP120mm Parity Drive: 1x WD Red 8TB Data Drives: 3x WD Red 4TB + 1x WD Red 8TB Cache Drive: 2x WD Black 1TB Total Drive Capacity: 7 comfortably, 11 creatively. Primary Use: Started as just a plex / deluge server but with the proliferation of docker containers it has become my dev, voip and at times game server. Likes: IPMI is fantastic for server work. 3 mini sas connectors means I can connect up to 14 sata devices before I need to install additional hardware to add sata connections. Tiny enough to live in my linen closet with a UPS. Dislikes: The fan that came with the cooler was unimpressive and threw a bearing after a few months. I was able to fix and improve the cooler by installing a conical duct and a 120mm PWM fan in place of the 95mm that came with the cooler. The cpu is fine but I wish I would have gone one step up and grabbed the one with HT. Add Ons Used: OpenVPN Server TUN mode, IPMI support, Dynamix File Integrity and Community Applications Future Plans: will be adding another 4TB red here soon. Also just finished implementing 2FA for openVPN so need to start giving remote users access to the server Boot (peak): 52 W Idle (avg): 32 W Active (avg): 82 W Light use (avg): 48 W Gallery Also don't worry about the last picture. the server normally lives on a metal plate to allow airflow to the bottom of the server. Was just removed for the quarterly filter cleaning. Another note is I modified the case slightly to use the extended ITX motherboard and the lower hard drive tray. Normally the longer mobo would block the lower tray from being used. I was able to spin the tray 180 degrees causing the drives to be mounted closer to the left of the case giving me adequate clearance. Edited July 31, 2017 by firetime updated psu 1 Quote Link to comment
De1taE1even Posted August 12, 2016 Share Posted August 12, 2016 I was all ready to recommend you get your valuable electronics off the floor! Then I read the whole post. Nice build! Quote Link to comment
mr-hexen Posted August 13, 2016 Share Posted August 13, 2016 Fellow Q25'er here, nice work... I have always been nervous about putting 3.5" drives in the removable tray. I've always stuck with laptop drives for now since they are designed for low airflow environments, and I had a few lying around. You've got two 3.5" drives there (hot WD blacks even), how are temps? Quote Link to comment
HellDiverUK Posted August 14, 2016 Share Posted August 14, 2016 Fellow Q25'er here, nice work... I have always been nervous about putting 3.5" drives in the removable tray. I've always stuck with laptop drives for now since they are designed for low airflow environments, and I had a few lying around. You've got two 3.5" drives there (hot WD blacks even), how are temps? Latest 1TB Blacks are just a rebranded single platter 1TB Blue, so they don't get warm at all. I'm pretty sure that's what he's using. Quote Link to comment
firetime Posted August 15, 2016 Author Share Posted August 15, 2016 Checking now, the one near the back is 36°C and the one near the front is 33°C. One is from 2012 and the other is newer but don't know the exact date (2012-2014). The reds were purchased just for this server while the blacks were on hand. I was all ready to recommend you get your valuable electronics off the floor! ... Funny enough had a mini flood in the house today. Condensate pump failed on the evaporator causing the reservoir to overflow. Managed to catch it in time but would have reached the server where it was in the photograph if I happened to away for the weekend. Quote Link to comment
garycase Posted August 15, 2016 Share Posted August 15, 2016 Nicely done ... good idea r.e. reversing the bottom tray so you could use an extended-ITX board without impacting the drive capacity. I've easily put 8 drives in a Q25 => 7 3.5" and one 2.5" SSD I am, however, curious about just what "creative" steps you envision that would allow 11 drives !! ... Total Drive Capacity: 7 comfortably, 11 creatively. ... Quote Link to comment
firetime Posted August 15, 2016 Author Share Posted August 15, 2016 Well I thought about moving the caches to ssd to free up two 3.5 slots and then a little bit of drive stacking using brackets resulting in something like this: So not quite 11 full drives, but sill fairly drive dense. If I went totally bonkers I know that I can fit a drive between the power supply and the left door of the case. Could get a bracket made that would grab onto the power supply. Quote Link to comment
garycase Posted August 15, 2016 Share Posted August 15, 2016 That would indeed do it => if you put 2 SSDs in (with a spacer between them for airflow) you'd have 11 drives in there with no problem -- 9 3.5" and 2 2.5" ... Of course your motherboard supports 14 drives 8) So you need a bit more creativity !! [You could add one more 3.5" internally "upright" (as you suggested); and then add a 2-port e-SATA bracket on the rear panel connected to the final 2 ports; and use a little 2-drive eSATA case sitting beside, behind, or on top of the case to hold those final 2 drives ] Quote Link to comment
garycase Posted August 15, 2016 Share Posted August 15, 2016 That would indeed do it => if you put 2 SSDs in (with a spacer between them for airflow) you'd have 11 drives in there with no problem -- 9 3.5" and 2 2.5" ... Of course your motherboard supports 14 drives 8) So you need a bit more creativity !! [You could add one more 3.5" internally "upright" (as you suggested); and then add a 2-port e-SATA bracket on the rear panel connected to the final 2 ports; and use a little 2-drive eSATA case sitting beside, behind, or on top of the case to hold those final 2 drives ] ... with this "loaded" configuration and 8TB WD Reds, you could have 88TB of storage in the array plus a 2-drive cache pool !! (or 80TB with dual parity) ... in a PC-Q25B !!! Quote Link to comment
firetime Posted August 16, 2016 Author Share Posted August 16, 2016 Ha if/when I need to get to that point I would most likely either build or purchase a 4 bay mini sas enclosure. Has the advantage of only needing to run the one sas connection along with power instead of multiple e-sata wires. Was looking at the LIAN LI PC-Q05B as a possibility for a lo profile hard drive enclosure that would match the server but the dimensions don't work well for full sized drives: If it was shorter in one dimension and longer in any other dimension it would work. Also updated original post with a few pics I missed also added power consumption as I realized the UPS has a built in watt meter. Quote Link to comment
a_n_d_y Posted September 13, 2016 Share Posted September 13, 2016 Well I thought about moving the caches to ssd to free up two 3.5 slots and then a little bit of drive stacking using brackets resulting in something like this: So not quite 11 full drives, but sill fairly drive dense. If I went totally bonkers I know that I can fit a drive between the power supply and the left door of the case. Could get a bracket made that would grab onto the power supply. Build looks awesome. What brackets are you using on the bottom? Quote Link to comment
firetime Posted September 21, 2016 Author Share Posted September 21, 2016 That pic was just a Photoshop to mock up drive placement. When/if I do end up stacking drives I'll make my own as I have access to laser cutters. Quote Link to comment
Superorb Posted September 28, 2016 Share Posted September 28, 2016 What kind of temps are you seeing for the drives during a parity check? Quote Link to comment
dstroot Posted October 11, 2016 Share Posted October 11, 2016 What MB/CPU would people recommend if building in this case today? Quote Link to comment
mr-hexen Posted October 11, 2016 Share Posted October 11, 2016 I like this one for a current spec system: http://www.newegg.ca/Product/Product.aspx?Item=N82E16813599009 Quote Link to comment
garycase Posted October 11, 2016 Share Posted October 11, 2016 I like this one for a current spec system: http://www.newegg.ca/Product/Product.aspx?Item=N82E16813599009 Agree ... that's a VERY nice board for a mini-ITX system. With 8 SATA ports, you're very unlikely to require an add-in controller card, and it's a server-grade board so you get ECC and Xeon support as well. The only thing "missing" that'd be nice-to-have is IPMI, but that's not really a big deal -- but DO be sure you buy a Xeon with integrated graphics if using this board. Quote Link to comment
mr-hexen Posted October 11, 2016 Share Posted October 11, 2016 What a shame this 9000+ passmark Xeon doesnt have Intel graphics... http://www.newegg.ca/Product/Product.aspx?Item=N82E16819117613R At that price, wowzers! Quote Link to comment
garycase Posted October 11, 2016 Share Posted October 11, 2016 That is indeed a very good price (~ $70 off because it's an "open box" unit). For another $100 you get a bit higher PassMark (10053) and Intel HD 530 graphics http://www.newegg.ca/Product/Product.aspx?Item=N82E16819117615 Quote Link to comment
spencers Posted October 12, 2016 Share Posted October 12, 2016 I like this one for a current spec system: http://www.newegg.ca/Product/Product.aspx?Item=N82E16813599009 Agree ... that's a VERY nice board for a mini-ITX system. With 8 SATA ports, you're very unlikely to require an add-in controller card, and it's a server-grade board so you get ECC and Xeon support as well. The only thing "missing" that'd be nice-to-have is IPMI, but that's not really a big deal -- but DO be sure you buy a Xeon with integrated graphics if using this board. Why do you recommend the CPU with graphics with the C236 board? Is integrated required if an nvidia card is installed (and passed through to a VM)? Quote Link to comment
mr-hexen Posted October 12, 2016 Share Posted October 12, 2016 Without a GPU for unRAID you'll have no way to see the console. I suppose it should work headless with all config through the webgui, but how would you edit the BIOS etc? With a nVidia GPU you could edit the BIOS and then pass it thru when unRAID boots. Quote Link to comment
garycase Posted October 12, 2016 Share Posted October 12, 2016 Clearly if you install a dedicated graphics card you don't need on-chip graphics. That card will, of course, use the only expansion slot on that AsRock board (or any other mini-ITX board). If you need it to pass-through to a VM, then indeed it's okay to not bother with on-chip graphics; but if you don't need a graphics card for pass-through, then on-chip graphics keeps the expansion slot free and eliminates the need to buy a graphics card. Quote Link to comment
Superorb Posted October 12, 2016 Share Posted October 12, 2016 Not to mention keeps power use to a minimum with integrated graphics. Quote Link to comment
garycase Posted October 12, 2016 Share Posted October 12, 2016 Not to mention keeps power use to a minimum with integrated graphics. True ... and many of us who build mini-ITX servers are very focused on keeping our power consumption as low as possible. For example, my Q25B system idles under 20w Quote Link to comment
TaterSalad Posted October 13, 2016 Share Posted October 13, 2016 I'm building a Q25B system and looking for some advice in another thread. If anyone has any thoughts, I'd greatly appreciate it! (Sorry for the double post, but this thread seems way more active. The items I'm looking at are on-sale and the sale ends tomorrow.) Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.