August 19, 20169 yr I'm running unRaid 6.1.9. Parity x1, data x5, cache x1. Everything is working, parity is checked and valid. How do I go about resetting everything without loosing data on my data drives? I have some plugins, but nothing fancy like dockers, VMs, or the like. They would be easy to reinstall and reconfigure. I'm trying to chase down some performance issues and this is the last thing to try before buying new hardware.
August 19, 20169 yr As long as you know what drive goes where. Specifically the parity and cache drives but the data drives are nice too. You don't need to worry about starting over. With unRAID v5 I essentially did that every time I upgraded. I would do a backup of the flash drive and then I pulled the key file off of it and then formatted it and installed from scratch each time. As long as I had the drive assignments it was fine. I just re-attached the drives to the correct slots, used the "parity is valid" check box and restarted with the new version. If unRAID didn't automatically start a parity check I would tell it to do one to confirm everything is still OK. I just made sure to do a non-correcting parity check so I could go back if needed.
August 19, 20169 yr Author Thanks! How does it know what my user shares and login/password are? Are these stored on the parity drive?
August 19, 20169 yr You would lose all these by resetting everything. Keep a copy of your config folder if you wish to restore them
August 19, 20169 yr Community Expert Thanks! How does it know what my user shares and login/password are? Are these stored on the parity drive? The parity drive doesn't contain any files. It is just a bunch of bits that correspond to the XOR of the bits of all other drives. Take a look at how parity works in the documentation. It isn't complicated at all and everything makes a lot more sense if you understand parity. You won't have a password if you start from a clean install. Any top level folder on cache or any array disk is automatically part of a user share named for that folder. If you don't make settings for a user share it will have default settings.
August 19, 20169 yr You would lose all these by resetting everything. Keep a copy of your config folder if you wish to restore them If you have made changes to the default settings of user shares, these will be lost, but the user shares themselves will be re-created with default settings based on the top level names of the folders on your disks. And by default no password is set for user root, this needs to be re-entered. Starting with an "empty" system won't loose any data on your disks, but requires you to re-assign disks and settings. This is a good approach when to ensure that no legacy stuff or installations are lingering around, and have a true 'clean' machine.
August 19, 20169 yr Author Great, your input is very appreciated everyone. I will make sure I have my drive names/locations documented. It sounds like "losing" user shares won't be a problem. They are not setup in any special way. Crossing my fingers I solve my performance problems this weekend and can save the money I was putting towards new server hardware for a new gaming monitor instead. I built this server back in 2010 so it has been through a few software updates to say the least.
August 19, 20169 yr I'm a little late here, but there's a wiki page that may be of help - Files on v6 boot drive The last section of the page is about Starting Over.
August 20, 20169 yr Author Thanks! It is not too late, I'm hoping to have some files transferred and a parity check done by the end of the weekend before I do the reset.
October 12, 20187 yr I couldn't help but notice that the question in the title hasn't been answered and I am looking for the answer. Please help. How to reset all settings and disk configuration in unRaid Thanks in advance Edited October 12, 20187 yr by LaswitchTech
October 12, 20187 yr Community Expert 12 minutes ago, LaswitchTech said: How to reset all settings and disk configuration in unRaid Redo the flash drive and only restore your license.
October 12, 20187 yr 11 minutes ago, johnnie.black said: Redo the flash drive and only restore your license. Is there a way to do it without redoing the flash drive tho ? Edited October 12, 20187 yr by LaswitchTech
October 12, 20187 yr Community Expert 2 minutes ago, LaswitchTech said: Is there a way to do it without redoing the flash drive tho ? Replace the config folder with the one from the download zip.
October 12, 20187 yr 19 minutes ago, johnnie.black said: Replace the config folder with the one from the download zip. Thanks
November 30, 20223 yr Backed up my flash files and just recently cannot login to root tried my backed files 6.9.2 and 6.11.5 then reformated flash and copy prokey and deleted the 3 files. Reboot server and it prompts for new pw it accepts and then try to login and put in new root pw and no response and no error message just blank Use roboform to save my pw's. Can someone suggest what I should do? worked on this for 1 solid hour and got no where need some help
November 30, 20223 yr Community Expert Since you posted on a very old thread, unclear what you have done. https://wiki.unraid.net/Manual/Troubleshooting#Lost_root_Password
November 30, 20223 yr Followed those steps from your link tried both methods listed in link. It prompts for new root pw and accepts new pw. Then I type it in and get the result where no error message and just a blank login screen like I showed above. Still not working
November 30, 20223 yr Community Expert Try a different browser, also make there are no Ad-blocker or firewalls blocking GUI access.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.