i got this from output.

 

smartctl version 5.38 [i486-slackware-linux-gnu] Copyright © 2002-8 Bruce Allen

Home page is http://smartmontools.sourceforge.net/

 

=== START OF INFORMATION SECTION ===

Device Model:    MAXTOR STM3500630AS

Serial Number:    9QG3WRHW

Firmware Version: 3.AAE

User Capacity:    500,106,780,160 bytes

Device is:        Not in smartctl database [for details use: -P showall]

ATA Version is:  7

ATA Standard is:  Exact ATA specification draft version not indicated

Local Time is:    Thu Feb 18 19:38:47 2010 GMT+8

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

 

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

 

General SMART Values:

Offline data collection status:  (0x82) Offline data collection activity

was completed without error.

Auto Offline Data Collection: Enabled.

Self-test execution status:      (  0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: ( 430) seconds.

Offline data collection

capabilities: (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities:            (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability:        (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: (  1) minutes.

Extended self-test routine

recommended polling time: ( 163) minutes.

 

SMART Attributes Data Structure revision number: 10

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate    0x000f  116  095  006    Pre-fail  Always      -      106064566

  3 Spin_Up_Time            0x0003  098  093  000    Pre-fail  Always      -      0

  4 Start_Stop_Count        0x0032  100  100  020    Old_age  Always      -      935

  5 Reallocated_Sector_Ct  0x0033  100  100  036    Pre-fail  Always      -      0

  7 Seek_Error_Rate        0x000f  080  060  030    Pre-fail  Always      -      113053394

  9 Power_On_Hours          0x0032  097  097  000    Old_age  Always      -      2904

10 Spin_Retry_Count        0x0013  100  100  097    Pre-fail  Always      -      0

12 Power_Cycle_Count      0x0032  099  099  020    Old_age  Always      -      1030

187 Reported_Uncorrect      0x0032  001  001  000    Old_age  Always      -      291

189 High_Fly_Writes        0x003a  100  100  000    Old_age  Always      -      0

190 Airflow_Temperature_Cel 0x0022  063  047  045    Old_age  Always      -      37 (Lifetime Min/Max 28/37)

194 Temperature_Celsius    0x0022  037  053  000    Old_age  Always      -      37 (0 19 0 0)

195 Hardware_ECC_Recovered  0x001a  093  053  000    Old_age  Always      -      161327039

197 Current_Pending_Sector  0x0012  001  001  000    Old_age  Always      -      4294967292

198 Offline_Uncorrectable  0x0010  001  001  000    Old_age  Offline      -      4294967292

199 UDMA_CRC_Error_Count    0x003e  200  200  000    Old_age  Always      -      0

200 Multi_Zone_Error_Rate  0x0000  100  253  000    Old_age  Offline      -      0

202 TA_Increase_Count      0x0032  099  252  000    Old_age  Always      -      1

 

SMART Error Log Version: 1

ATA Error Count: 323 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

 

Error 323 occurred at disk power-on lifetime: 2876 hours (119 days + 20 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  10 51 01 ee 57 38 ea

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  37 00 01 ee 57 38 ea 00      00:09:51.547  SET MAX ADDRESS EXT

  27 00 00 ee 57 38 e0 00      00:09:51.507  READ NATIVE MAX ADDRESS EXT

  37 00 00 ee 57 38 ea 00      00:09:51.506  SET MAX ADDRESS EXT

  27 00 01 ee 57 38 e0 00      00:09:51.506  READ NATIVE MAX ADDRESS EXT

  37 00 01 ee 57 38 ea 00      00:09:56.303  SET MAX ADDRESS EXT

 

Error 322 occurred at disk power-on lifetime: 2876 hours (119 days + 20 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  10 51 01 ee 57 38 ea

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  37 00 01 ee 57 38 ea 00      00:09:51.547  SET MAX ADDRESS EXT

  27 00 00 ee 57 38 e0 00      00:09:51.507  READ NATIVE MAX ADDRESS EXT

  37 00 00 ee 57 38 ea 00      00:09:51.506  SET MAX ADDRESS EXT

  27 00 01 2f 60 38 e0 00      00:09:51.506  READ NATIVE MAX ADDRESS EXT

  29 00 01 2f 60 38 e0 00      00:09:51.506  READ MULTIPLE EXT

 

Error 321 occurred at disk power-on lifetime: 2363 hours (98 days + 11 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  10 51 01 ee 57 38 ea

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  37 00 01 ee 57 38 ea 00      00:36:34.329  SET MAX ADDRESS EXT

  27 00 00 ee 57 38 e0 00      00:36:34.113  READ NATIVE MAX ADDRESS EXT

  37 00 00 ee 57 38 ea 00      00:36:34.048  SET MAX ADDRESS EXT

  27 00 01 ee 57 38 e0 00      00:36:31.968  READ NATIVE MAX ADDRESS EXT

  37 00 01 ee 57 38 ea 00      00:36:31.909  SET MAX ADDRESS EXT

 

Error 320 occurred at disk power-on lifetime: 2363 hours (98 days + 11 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  10 51 01 ee 57 38 ea

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  37 00 01 ee 57 38 ea 00      00:36:27.817  SET MAX ADDRESS EXT

  27 00 00 ee 57 38 e0 00      00:36:27.817  READ NATIVE MAX ADDRESS EXT

  37 00 00 ee 57 38 ea 00      00:36:27.817  SET MAX ADDRESS EXT

  27 00 01 2f 60 38 e0 00      00:36:31.968  READ NATIVE MAX ADDRESS EXT

  29 00 01 2f 60 38 e0 00      00:36:31.909  READ MULTIPLE EXT

 

Error 319 occurred at disk power-on lifetime: 2363 hours (98 days + 11 hours)

  When the command that caused the error occurred, the device was active or idle.

 

  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  10 51 01 ee 57 38 ea

 

  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  37 00 01 ee 57 38 ea 00      00:28:21.109  SET MAX ADDRESS EXT

  27 00 00 ee 57 38 e0 00      00:28:21.108  READ NATIVE MAX ADDRESS EXT

  37 00 00 ee 57 38 ea 00      00:28:27.224  SET MAX ADDRESS EXT

  27 00 01 ee 57 38 e0 00      00:28:27.165  READ NATIVE MAX ADDRESS EXT

  37 00 01 ee 57 38 ea 00      00:28:26.949  SET MAX ADDRESS EXT

 

SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error

# 1  Short offline      Completed without error      00%      2876        -

 

SMART Selective self-test log data structure revision number 1

SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

 

 

 

thanks

I'll leave it to the experts here to confirm but from the looks of it, your hard drive is in a terminal phase:

 

106064566  Raw_Read_Error_Rate and 4.294.967.292 sectors pending reallocation. That's not good. If the hard drive is still under warranty, return it.

 

Copy any data off of it and try Joe L's preclear script,  see if the numbers change.  smart sometimes reports garbage.

 

Is the drive causing a problem?

The drive was max'd out with movies, so I copied all of them off and formatted drive, than moved it into my new array. The drive hasn't caused me any issues (that I know of). Thanks for the info, I appreciate it.