March 21, 201016 yr I just installed Unraid i precleared my 2 2TB hard drives and i wanted to transfer some files before i do a parity sync. I also installed the sabnzbdplus 5.0 package. The problem i get is Sabnzbd will download at 3MB/s for a few minutes and then it will becomes slow takes like 5min for it to load a page and speed drops to 0. The shares i can download from the at 13MB/s but if i try to put a files on the share it goes very slow or it says it couldn't connect. If i reboot the system speed comes again but drops after a few minutes same if i reboot the router i have had sabnzbd running on a ubuntu system and it was working fine. I have tried a bran new cable cat5e. Also i noticed that sabnzbd once completed a download but extracting became extremely slow something like 200KB per min. Oh also when this happens sometimes it wont connect to unraid at all it will say firefox failed to connect and i have to retry a few times. Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes NIC driver info (from ethtool -i) driver: r8169 version: 2.3LK-NAPI firmware-version: bus-info: 0000:02:00.0 Ethernet config info (from ifconfig) eth0 Link encap:Ethernet HWaddr 00:24:1d:1c:ff:f9 inet addr:192.168.1.121 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:121233 errors:0 dropped:0 overruns:0 frame:0 TX packets:67427 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:181774794 (173.3 MiB) TX bytes:4552853 (4.3 MiB) Interrupt:26 Base address:0x6000 any ideas what it could be?
March 21, 201016 yr any ideas what it could be? No, because a syslog covering the time of the events you describe is needed for any analysis.
March 21, 201016 yr Author i didn't see anything in syslogs that's why i didn't post it but here it is. I just installed sabnzbd on my windows computer to see if it is the router but it had no problems. syslog-2010-03-20.txt
March 21, 201016 yr Author i got rid of sabnzbd to see if that's the problem. I tried to transfer a video 1.5Gb and it transfers around 5% then speed starts to drop to 0.
March 21, 201016 yr i didn't see anything in syslogs that's why i didn't post it but here it is. I just installed sabnzbd on my windows computer to see if it is the router but it had no problems. That syslog covers about 2 seconds of time from 23:23:13 to 23:23:15. I somehow do not think it has the clues needed. General advice, perform a file-system check on each of your file-systems. Instructions in the wiki: http://lime-technology.com/wiki/index.php?title=Check_Disk_Filesystems
March 21, 201016 yr Author will try that but what i did was install 4.4.2 so far i was able to transfer the file to the share no drop in speed same with sabnzbd could this be a bug in 4.5.3?
March 21, 201016 yr Author I cant right now still using 4.4.2 and its working fine i don't know if i want to switch back to 4.5.3. Isn't the syslog i posted the whole thing?
March 27, 201016 yr Author i didn't see anything in syslogs that's why i didn't post it but here it is. I just installed sabnzbd on my windows computer to see if it is the router but it had no problems. That syslog covers about 2 seconds of time from 23:23:13 to 23:23:15. I somehow do not think it has the clues needed. General advice, perform a file-system check on each of your file-systems. Instructions in the wiki: http://lime-technology.com/wiki/index.php?title=Check_Disk_Filesystems Unraid has been working fine for the last 5 days no speed drops at all. But i soon need to use the latest version that i had the problem if 4.4.2 is working fine could it still be the file-systems?
March 27, 201016 yr Author i ran file system check looks like its fine Samba Stopped /dev/md1 Unmounted Checking /dev/md1 (/dev/sdd) reiserfsck 3.6.19 (2003 www.namesys.com) ************************************************************* ** If you are using the latest reiserfsprogs and it fails ** ** please email bug reports to [email protected], ** ** providing as much information as possible -- your ** ** hardware, kernel, patches, settings, all reiserfsck ** ** messages (including version), the reiserfsck logfile, ** ** check the syslog file for any related information. ** ** If you would like advice on using this program, support ** ** is available for $25 at www.namesys.com/support.html. ** ************************************************************* Will read-only check consistency of the filesystem on /dev/md1 Will put log info to 'stdout' ########### reiserfsck --check started at Sat Mar 27 08:30:34 2010 ########### Replaying journal.. Reiserfs journal '/dev/md1' in blocks [18..8211]: 0 transactions replayed Checking internal tree..finished Comparing bitmaps..finished Checking Semantic tree: finished No corruptions found There are on the filesystem: Leaves 159881 Internal nodes 1014 Directories 432 Other files 2225 Data block pointers 161508504 (0 of them are zero) Safe links 0 ########### reiserfsck finished at Sat Mar 27 09:35:27 2010 ########### /dev/md1 mounted on /mnt/disk1 Samba Started
March 27, 201016 yr Author Mar 22 20:32:04 Tower kernel: ata4: failed due to HW bug, retry pmp=0 Mar 22 20:32:04 Tower kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 22 20:32:04 Tower kernel: ata4.00: HPA detected: current 3907029168, native 18446744073321613488 Mar 22 20:32:04 Tower kernel: ata4.00: ATA-8: WDC WD20EADS-00R6B0, 01.00A01, max UDMA/133 Mar 22 20:32:04 Tower kernel: ata4.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32) Mar 22 20:32:04 Tower kernel: ata4.00: configured for UDMA/133 Is this normal? i know disabled save bios to disk in bios. http://www.wdc.com/en/products/products.asp?driveid=773 here it says User Sectors Per Drive 3,907,029,168 im so confused. System file check said no corruption so i don't know what to do. If you look at the logs all my drives do this. I still think my problem is some kind of bug in 4.5.3 why else does 4.4.2 work perfect. syslog-2010-03-27.txt
Archived
This topic is now archived and is closed to further replies.