sk32md Posted April 13, 2017 Share Posted April 13, 2017 I cant make sense of this can anyone please help??? Its in the attached bmp. Its basically 2 faulty disks, one being a parity drive but everything including the files show ok??? New Bitmap Image.bmp Quote Link to comment
Squid Posted April 14, 2017 Share Posted April 14, 2017 You've had write failures to parity 2 and disk 1, so unRaid has disabled the disks. All the files are showing because unRaid is doing what it's supposed to do: emulating the contents of disk 1, and the surviving parity disk is still protecting the array. You should post your diagnostics before you reboot so that the community can see what led up to the dual failure, and advise on a course of action. 1 Quote Link to comment
sk32md Posted April 14, 2017 Author Share Posted April 14, 2017 Sorry! Was I supposed to put that in a text file? 1 Quote Link to comment
JorgeB Posted April 14, 2017 Share Posted April 14, 2017 35 minutes ago, sk32md said: Sorry! Was I supposed to put that in a text file? No, you are supposed to go to Tools -> Diagnostics and post the zip, preferably after the problem but before rebooting, looks like you rebooted, but post them anyway so we can at least check the SMART reports. 1 Quote Link to comment
sk32md Posted April 14, 2017 Author Share Posted April 14, 2017 tower-diagnostics-20170414-1510.zip Quote Link to comment
JorgeB Posted April 14, 2017 Share Posted April 14, 2017 Like I said before since you rebooted we can see what happened, but SMART for both disks is OK and since they are both on a SAS2LP it could have been the typical SAS2LP issue. You can rebuild disk1 and sync parity at the same time using the existing disks, if there are issues again be sure to grab the diags before rebooting. PS. You're still on v6.2, you should update to latest release. PS2. Disk1 has a lot of UDMA_CRC errors: 199 UDMA_CRC_Error_Count 0x003e 200 001 000 Old_age Always - 11330 These may be old and unrelated but if this value continues to increase you need to replace that SATA cable. 1 Quote Link to comment
sk32md Posted April 14, 2017 Author Share Posted April 14, 2017 Sounds like a good solution. Soooooooooo how do you rebuild the drive and parity at the same time? Quote Link to comment
JorgeB Posted April 14, 2017 Share Posted April 14, 2017 Stop array, unassign both disks, start array, stop array, re-assign both disks in their original slots, start array to begin data rebuild and parity sync. 1 Quote Link to comment
sk32md Posted April 14, 2017 Author Share Posted April 14, 2017 2 Days 4 Hours and 45 minutes to go. Thanks for your help. Quote Link to comment
sk32md Posted April 14, 2017 Author Share Posted April 14, 2017 So another error occurred. I did't restart and have attached a diagnostic file this time. tower-diagnostics-20170414-1628.zip Quote Link to comment
JorgeB Posted April 15, 2017 Share Posted April 15, 2017 8 hours ago, johnnie.black said: since they are both on a SAS2LP it could have been the typical SAS2LP issue. My hunch was correct, it's the SAS2LP crashing. These sometimes help: -disable vt-d if you don't need it -check for a board bios update -use the controller in another slot (you should change it in this case anyway as it's in the x4 slot that shares the DMI with all other disks, I think you have an empty x8 CPU slot, it should be there for best performance) If none of the above helps consider getting an LSI controller. 1 Quote Link to comment
sk32md Posted April 16, 2017 Author Share Posted April 16, 2017 Looks like the bios is up to date. I made the change over in slots, (My mistake I was thinking it was like my z97 board that does x8x4x4 in 3.0). I had also noticed the white sata ports on my board were improperly installed on the 3.0 slots instead of the 2.0 so I only put a 1tb drive on one of the 2.0 ports and used the 3.0 ports for the cache drives. I then installed all of the data drives, except the 1tb, on the SAS2LP card as it was rock solid reliable until i added a couple new drives last month and rewired for asthetics. It is now copying over @ 85mbps with no errors so far............ Quote Link to comment
sk32md Posted April 17, 2017 Author Share Posted April 17, 2017 The rebuild finished with 0 errors Quote Link to comment
shanelovell Posted April 18, 2017 Share Posted April 18, 2017 These forums are great, I just had a disk error as well but was unable to retrieve the log files as the server GUI became unresponsive which forced me to hard reboot. The unassign/reassign disk seems to have done the trick and rebuild is ongoing now. I will update as it progresses. Quote Link to comment
shanelovell Posted April 19, 2017 Share Posted April 19, 2017 Rebuild completed with no errors. Happy camper again. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.