January 4, 20188 yr Version: 6.4.0_rc18f I bought a new 4TB drive. Slapped it in via a hot swap bay, but it didn't show up in the GUI. I then attempted to reboot and things went sideways (known issue with UEFI boot not saving the boot order on X99 MBs...). That was resolved and the system now boots into unRAID, however, I'm getting a red X on disk 9 and the error "Device is disabled. Contents emulated." I grabbed the SMART report (I think) and have attached it here. Is the drive toast? Hardware: Case: Lian Li PC-A77FB Motherboard: Asus X99-A II ATX LGA2011-3 Motherboard Processor: Intel® Core™ i7-6850K RAM: G.Skill Ripjaws V Series 16GB (2 x 8GB) DDR4-3200 Memory Drive Cage(s): 3x Supermicro CSE-M35T-1B Hot Swap Bay Hard Drives: Parity ST4000DM005-2DP166_WDH2S61F - 4 TB (sdc) Disk 1 WDC_WD20EADS-00R6B0_WD-WCAVY5374796 - 2 TB (sdg) Disk 2 WDC_WD30EZRX-19D8PB0_WD-WMC4N0J7D8TT - 3 TB (sde) Disk 3 WDC_WD20EARS-00MVWB0_WD-WCAZA9034298 - 2 TB (sdf) Disk 4 ST3000DM008-2DM166_Z504PPXT - 3 TB (sdh) Disk 5 ST4000DM005-2DP166_WGY0E53A - 4 TB (sdk) Disk 6 ST3000DM001-1CH166_W1F23145 - 3 TB (sdm) Disk 7 WDC_WD30EZRX-00SPEB0_WD-WCC4E0NP7NLR - 3 TB (sdl) Disk 8 ST3000DM001-1ER166_Z5029NBR - 3 TB (sdj) Disk 9 ST3000DM008-2DM166_Z503HXCF - 3 TB (sdi) Cache Drive: Samsung_SSD_850_EVO_250GB_S2R5NX0J445962N - 250 GB (sdb) Boot Device: Flash JD_FireFly - 8 GB (sda) New Unassigned Drive: sdd ST4000DM004-2CV104_ZFN0BNMN tower-smart-20180103-2008.zip tower-diagnostics-20180103-2018.zip
January 4, 20188 yr Community Expert SMART looks fine but since it's the infamous ST3000DM001 you should at least run an extended SMART test before using again.
January 4, 20188 yr Author Thanks, Johnnie. Would you be able to point me to an article on how I run the extended SMART test from the GUI? I can't seem to find it other than to say you should run it from the GUI and then it provides the command line options. If it is ok, how do I get rid of the error/red X?
January 4, 20188 yr Community Expert Not sure you can run SMART tests on a disable disk using the wegGUI, but don't think so, you can use the console: smartctl --test=long /dev/sdX 18 minutes ago, Netbug said: If it is ok, how do I get rid of the error/red X? You need to rebuild to the same disk, before rebuilding check that the contents on the emulated disk look correct, whatever is there is what's going to be rebuilt: https://lime-technology.com/wiki/Troubleshooting#Re-enable_the_drive
January 4, 20188 yr 2 hours ago, johnnie.black said: Not sure you can run SMART tests on a disable disk using the wegGUI With unRAID 6.4 it is possible (can't remember from which RC, but use latest RC anyway). Older unRAID versions you'll need CLI.
Archived
This topic is now archived and is closed to further replies.