impmonkey Posted July 21, 2018 Share Posted July 21, 2018 I updated to the latest stable version and now my system will not boot. This is the prompt it stops at: I have tried to boot in safe mode without luck. Sometimes it will hang at the "strarting RPC NSM" prompt also. I have tried removing all my custom lines in the go file along with the sysconfig file without luck. Any ideas? Quote Link to comment
impmonkey Posted July 21, 2018 Author Share Posted July 21, 2018 It seems to hang up somewhere in that area of the boot. This last time it was at the "compiling GSettings" Will Test Ram and Report back. Quote Link to comment
impmonkey Posted July 21, 2018 Author Share Posted July 21, 2018 Memory tested fine. I am at a loss at this point. Quote Link to comment
Frank1940 Posted July 21, 2018 Share Posted July 21, 2018 Download the latest version of the software from the LimeTech website. Unzip the file and copy all of the bz* files to the root of your flash drive. Quote Link to comment
impmonkey Posted July 21, 2018 Author Share Posted July 21, 2018 6.5.3 stopped at starting NTP 6.5.2 stopped at the same Network Status Monitor bad usb drive??? Quote Link to comment
Frank1940 Posted July 21, 2018 Share Posted July 21, 2018 Pull the flash drive, plug it into a PC and run chkdsk on it. Quote Link to comment
impmonkey Posted July 21, 2018 Author Share Posted July 21, 2018 Ran it. Found bunch of errors, coverted lost chains to rec files. Ran it again with the switches /f /r /x Completed, ejected, inserted into server. Stopped at starting SAMBA again. I have a backup of the config file. I might just try to move it to a new drive. Any other ideas? Quote Link to comment
impmonkey Posted July 21, 2018 Author Share Posted July 21, 2018 (edited) Installed to a new usb key with the installer. Copied my config folder to the drive, ejected, booted on server. Same thing..... Odd Edited July 21, 2018 by impmonkey Quote Link to comment
Frank1940 Posted July 21, 2018 Share Posted July 21, 2018 OK try remaking the new flash drive without copying the configurations files/folders. Quote Link to comment
impmonkey Posted July 21, 2018 Author Share Posted July 21, 2018 (edited) Tried to use a fresh install. Same thing. Removed my dedicated gpu, went down to one stick of ram, removed extra nic card, disconnected drives. Same thing. Maybe I need an older version that what is currently on the site. Not sure of the exact version I had but it was older than 6.5.2 Any know issues with the c602 chipset boards? Running a Gigabyte GA-7PESH1 board with dual Xeons and about 96gb of memory. Edited July 21, 2018 by impmonkey Quote Link to comment
impmonkey Posted July 21, 2018 Author Share Posted July 21, 2018 Found an old copy of 6.3.5. Copied the BZ* files to the root of the drive. Boots right up. For sure something weird on 6.5.X. Any way I can troubleshoot this? Quote Link to comment
Frank1940 Posted July 22, 2018 Share Posted July 22, 2018 It has been quite a while without a response. What I would suggest is that you post up to the release thread for 6.5.3 (that is the version that you upgrade to?) and briefly list the steps you took and a link to this thread. Lime Tech does not monitor this sub-forum as religiously as they do the release threads. Perhaps, they will have some thoughts as where to go from here. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.