Jump to content

Drive disabled - SMART passed - Is it ok?


Recommended Posts

I have 5x 3TB drives. 2 are parity, 3 are data. My toshiba 3tb (parity 2) showed up with a red X some time after I transferred a bit of data to the unraid arroy. The server sits undisturbed by me in my rack (which probably vibrates like crazy).

 

I ran the extended SMART test and the drive passed. Should I toss this drive or keep using it?

 

Here's the download:

 

smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.9.30-unRAID] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 3.5" DT01ACA... Desktop HDD
Device Model:     TOSHIBA DT01ACA300
Serial Number:    --------------------
LU WWN Device Id: 5 000039 ff4dcc23c
Firmware Version: MX6OABB0
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Jul 26 18:33:11 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         (22222) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   1) minutes.
Extended self-test routine
recommended polling time:      ( 371) minutes.
SCT capabilities:            (0x003d)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   139   139   054    Pre-fail  Offline      -       71
  3 Spin_Up_Time            0x0007   140   140   024    Pre-fail  Always       -       392 (Average 425)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       207
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   124   124   020    Pre-fail  Offline      -       33
  9 Power_On_Hours          0x0012   098   098   000    Old_age   Always       -       19982
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       104
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       469
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       469
194 Temperature_Celsius     0x0002   162   162   000    Old_age   Always       -       37 (Min/Max 15/48)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       332

SMART Error Log Version: 1
ATA Error Count: 332 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 332 occurred at disk power-on lifetime: 19957 hours (831 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 80 d0 c2 2b 09  Error: ICRC, ABRT at LBA = 0x092bc2d0 = 153862864

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 50 c2 2b 40 00   4d+20:30:26.894  WRITE FPDMA QUEUED
  ef 10 02 00 00 00 00 00   4d+20:30:26.697  SET FEATURES [Enable SATA feature]
  ef 02 00 00 00 00 00 00   4d+20:30:26.697  SET FEATURES [Enable write cache]
  ef aa 00 00 00 00 00 00   4d+20:30:26.697  SET FEATURES [Enable read look-ahead]
  ef 03 46 00 00 00 00 00   4d+20:30:26.697  SET FEATURES [Set transfer mode]

Error 331 occurred at disk power-on lifetime: 19957 hours (831 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 90 c0 c4 2b 09  Error: ICRC, ABRT at LBA = 0x092bc4c0 = 153863360

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 50 c2 2b 40 00   4d+20:30:26.645  WRITE FPDMA QUEUED
  ef 10 02 00 00 00 00 00   4d+20:30:26.448  SET FEATURES [Enable SATA feature]
  ef 02 00 00 00 00 00 00   4d+20:30:26.448  SET FEATURES [Enable write cache]
  ef aa 00 00 00 00 00 00   4d+20:30:26.448  SET FEATURES [Enable read look-ahead]
  ef 03 46 00 00 00 00 00   4d+20:30:26.448  SET FEATURES [Set transfer mode]

Error 330 occurred at disk power-on lifetime: 19957 hours (831 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 90 c0 c4 2b 09  Error: ICRC, ABRT at LBA = 0x092bc4c0 = 153863360

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 50 c2 2b 40 00   4d+20:30:26.395  WRITE FPDMA QUEUED
  ef 10 02 00 00 00 00 00   4d+20:30:26.141  SET FEATURES [Enable SATA feature]
  ef 02 00 00 00 00 00 00   4d+20:30:26.141  SET FEATURES [Enable write cache]
  ef aa 00 00 00 00 00 00   4d+20:30:26.141  SET FEATURES [Enable read look-ahead]
  ef 03 46 00 00 00 00 00   4d+20:30:26.141  SET FEATURES [Set transfer mode]

Error 329 occurred at disk power-on lifetime: 19957 hours (831 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 90 c0 c4 2b 09  Error: ICRC, ABRT at LBA = 0x092bc4c0 = 153863360

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 50 c2 2b 40 00   4d+20:30:25.648  WRITE FPDMA QUEUED
  ef 10 02 00 00 00 00 00   4d+20:30:25.452  SET FEATURES [Enable SATA feature]
  ef 02 00 00 00 00 00 00   4d+20:30:25.452  SET FEATURES [Enable write cache]
  ef aa 00 00 00 00 00 00   4d+20:30:25.452  SET FEATURES [Enable read look-ahead]
  ef 03 46 00 00 00 00 00   4d+20:30:25.452  SET FEATURES [Set transfer mode]

Error 328 occurred at disk power-on lifetime: 19957 hours (831 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 90 c0 c4 2b 09  Error: ICRC, ABRT at LBA = 0x092bc4c0 = 153863360

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 00 50 c2 2b 40 00   4d+20:30:25.399  WRITE FPDMA QUEUED
  ef 10 02 00 00 00 00 00   4d+20:30:25.262  SET FEATURES [Enable SATA feature]
  ef 02 00 00 00 00 00 00   4d+20:30:25.262  SET FEATURES [Enable write cache]
  ef aa 00 00 00 00 00 00   4d+20:30:25.262  SET FEATURES [Enable read look-ahead]
  ef 03 46 00 00 00 00 00   4d+20:30:25.261  SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     19966         -
# 2  Short offline       Completed without error       00%     19959         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

Link to comment

You might want to change the SATA cable just to be on the safe side.  Make sure that it has a retention force when you attempt to disconnect it. No resistance-- you have real potential of having a flaky connection.  After doing all of this make sure that you have not loosened any of the other SATA connectors.   (The SATA connector is the posterchild of not to design a connector system!!!!) 

Link to comment

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...