trurl Posted August 7, 2018 Share Posted August 7, 2018 RAID or unRAID is not (has never been) a substitute for backups. Plenty of ways to lose data that have nothing to do with a disk failure. Quote Link to comment
[email protected] Posted August 7, 2018 Author Share Posted August 7, 2018 Fair enough. Thanks for the input Quote Link to comment
JorgeB Posted August 7, 2018 Share Posted August 7, 2018 12 hours ago, [email protected] said: syslog on flash (after doing cp line) shows blank Suggestions? Reboot, try syncing the new parity again and if it starts getting slow grab the syslog then (and the SMART reports), I'd prefer to see what's wrong with the server before doing the new config. Quote Link to comment
[email protected] Posted August 13, 2018 Author Share Posted August 13, 2018 Hello @johnnie.black Sorry for the delay in responding... I've been super busy with work. OK, so I restarted like you suggested and went to run the parity build again, but found that my parity drive was gone. Hmmmm. I'm pretty sure this is a problem with my hardware, and further, I am pretty sure this was the cause of my initial parity failure and subsequent speed issues... I just didn't recognize it. I have since connected the parity drive to an alternate power and SATA connection within the box, and have successfully built parity. I am now in the process of checking built parity. So far so good. And a couple items of note... 1. I have backed up all data contained on the remaining 4 data drives, so I am free to get to it with the recovery attempt if you're still willing to help 2. An item I failed to mention before is that I have my drives segregated by data type, so the information on the failed drive is all one type of information. All of the other drives are another type of information. I am hoping that maybe helps the prognosis despite me having remounted those data drives. Anyway, just thought I should mention it. I think that's it. Assuming the parity finished without issue, I am ready to move forward with your assistance. Thank you! Quote Link to comment
JorgeB Posted August 13, 2018 Share Posted August 13, 2018 You need a spare disk of the same size of the missing disk, to get the emulated disk, rebuilding is optional. -Utils -> New Config -using the old parity and a new spare disk assign all disks, double check parity is the parity slot-check both "parity is already valid" and "maintenance mode" before starting the array -start the array -stop array, unassign the missing disk -start array, check emulated disk mounts and contents look correct You can stop here if you just want to check or copy the data from the emulated disk, to rebuild: -stop array, reassign disk -start array to begin rebuild This only works if all but the missing disks are unchanged and synced with the parity disk used. Quote Link to comment
[email protected] Posted August 19, 2018 Author Share Posted August 19, 2018 Thank you, @johnnie.black I finally had the time to try this out. I went through the steps and everything went fine until I started the array after unassigning the missing disk. At that point, it stalled for quite a bit attempting to mount the disks. It finally pushed through, but none of the missing disk data (none of the shares or files within) appeared as I had hoped. Can I ask, if I share the log file, can you tell why this might be? (I'm assuming it is simply because parity was not fully built again on what I originally thought had been a failed disk, and simply telling it parity was valid wasnt enough?) And depending on your answer(s) to the above, does this mean I should assume that there is no unraid trickery to try to recover data any longer? Thank you again UNRAID LOG FILE - 20180819.txt Quote Link to comment
JorgeB Posted September 1, 2018 Share Posted September 1, 2018 Sorry, was away for a while, can't download the log, please re-post. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.