spazmc Posted September 14, 2018 Share Posted September 14, 2018 Is there a line/command I can add to my Go File to stop USB suspend? I think it maybe causing a reoccurring fault with lose of communication to UPS. Unraid 6.5.3 Quote Link to comment
Vr2Io Posted September 15, 2018 Share Posted September 15, 2018 (edited) In fact, Unraid won't suspend USB. Also no problem for UPS ubder apcupsd or nut. Edited September 15, 2018 by Benson Quote Link to comment
unevent Posted September 15, 2018 Share Posted September 15, 2018 Checked mine and none have suspend enabled so I would agree it is disabled by default. Lots of Google hits to be found with communication issues/commlost errors with solutions that vary depending on the cause. What UPS and UPS monitor are you using and the setup configuration? Quote Link to comment
spazmc Posted September 15, 2018 Author Share Posted September 15, 2018 (edited) Online 100.0 Percent 75.0 Minutes - - 11.0 Percent Online Manual Start APC UPS daemon: yes UPS cable: USB Custom UPS cable: UPS type: USB Device: Battery level to initiate shutdown (%): Runtime left to initiate shutdown (minutes): Time on battery before shutdown (seconds): Turn off UPS after shutdown: UPS Details Key Value Key Value APC 001,044,1067 DATE 2018-09-15 07:30:52 -0400 HOSTNAME Server VERSION 3.14.14 (31 May 2016) slackware UPSNAME Server CABLE USB Cable DRIVER USB UPS Driver UPSMODE Stand Alone STARTTIME 2018-09-11 19:37:43 -0400 MODEL Smart-UPS 1500 STATUS Online LINEV 120.9 Volts LOADPCT 11.0 Percent BCHARGE 100.0 Percent TIMELEFT 75.0 Minutes MBATTCHG 10 Percent MINTIMEL 10 Minutes MAXTIME 300 Seconds OUTPUTV 120.9 Volts SENSE High DWAKE -1 Seconds DSHUTD 90 Seconds LOTRANS 106.0 Volts HITRANS 127.0 Volts RETPCT 0.0 Percent ITEMP 30.6 C ALARMDEL 30 Seconds BATTV 27.4 Volts LINEFREQ 60.0 Hz LASTXFER Low line voltage NUMXFERS 10 XONBATT 2018-09-14 05:59:22 -0400 TONBATT 0 Seconds CUMONBATT 13 Seconds XOFFBATT 2018-09-14 05:59:22 -0400 SELFTEST NO STESTI 14 days STATFLAG 0x05000008 MANDATE 2002-10-20 SERIALNO AS0242233944 BATTDATE 2017-01-27 NOMOUTV 120 Volts NOMBATTV 24.0 Volts FIRMWARE 601.3.D USB FW:1.5 END APC 2018-09-15 07:31:03 -0400 Edited September 15, 2018 by spazmc Quote Link to comment
spazmc Posted September 15, 2018 Author Share Posted September 15, 2018 I could be the UPS self test causing it . I see this message allot. Quote Link to comment
unevent Posted September 15, 2018 Share Posted September 15, 2018 Port your diagnostics file, located in the GUI - Tools - Diagnostics. Quote Link to comment
spazmc Posted September 16, 2018 Author Share Posted September 16, 2018 Here it is. server-diagnostics-20180916-1747.zip Quote Link to comment
unevent Posted September 18, 2018 Share Posted September 18, 2018 I see some oddities in the log. Have some cables/power cords loose? Sep 12 04:10:56 Server apcupsd[3365]: Power failure. Sep 12 04:11:00 Server apcupsd[3365]: Power is back. UPS running on mains. Sep 12 05:55:33 Server kernel: usb 2-1.3: USB disconnect, device number 4 Sep 12 05:55:33 Server kernel: usb 2-1.3: new low-speed USB device number 8 using ehci-pci Sep 12 05:55:33 Server kernel: hid-generic 0003:051D:0002.0005: hiddev96,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 1500 FW:601.3.D USB FW:1.5] on usb-0000:00:1d.0-1.3/input0 Sep 12 05:55:40 Server apcupsd[3365]: Communications with UPS restored. ... Sep 12 12:08:13 Server kernel: e1000e: eth0 NIC Link is Down Sep 12 12:08:14 Server ntpd[1640]: Deleting interface #2 eth0, 192.168.1.20#123, interface stats: received=123, sent=124, dropped=0, active_time=59418 secs ... Sep 12 12:08:25 Server apcupsd[3365]: Power failure. Sep 12 12:08:25 Server apcupsd[3365]: Power is back. UPS running on mains. Sep 12 12:08:26 Server apcupsd[3365]: Power failure. Sep 12 12:08:27 Server apcupsd[3365]: Power is back. UPS running on mains. Sep 12 12:08:41 Server kernel: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx ... Sep 12 12:09:33 Server kernel: e1000e: eth0 NIC Link is Down ... Sep 12 12:09:35 Server apcupsd[3365]: Power failure. Sep 12 12:09:40 Server apcupsd[3365]: Power is back. UPS running on mains. Sep 12 12:10:01 Server kernel: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx ... Sep 12 13:21:56 Server kernel: usb 2-1.3: USB disconnect, device number 8 Sep 12 13:21:56 Server kernel: usb 2-1.3: new low-speed USB device number 9 using ehci-pci Sep 12 13:21:57 Server kernel: hid-generic 0003:051D:0002.0006: hiddev96,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 1500 FW:601.3.D USB FW:1.5] on usb-0000:00:1d.0-1.3/input0 Sep 12 13:22:04 Server apcupsd[3365]: Communications with UPS restored. Sep 12 13:22:05 Server apcupsd[3365]: Power failure. Sep 12 13:22:05 Server apcupsd[3365]: Power is back. UPS running on mains. Quote Link to comment
spazmc Posted September 18, 2018 Author Share Posted September 18, 2018 (edited) Some of them are probably blips in are power if that is the fault you are going to get. I will check power cables. The Eth0 fault could be. VM mac addressing crashes my switch. Need better switch.( vlan support ) Edited September 18, 2018 by spazmc more info Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.