KR1SeS Posted September 27, 2018 Share Posted September 27, 2018 (edited) Hey guys I was hoping to get a clear answer on the commands to issue in order to flash my new LSI 9211-8i to the latest firmware in IT mode. I'm going to use an older Dell that should be a BIOS and not UEFI, so we can avoid issues with trying to accomplish this on a newer motherboard. I'm following this guide: https://nguvu.org/freenas/Convert-LSI-HBA-card-to-IT-mode/ After reading posts from this and other forums, I feel like it's not necessary to flash the mtpsas2.rom BIOS for use with my unRAID server with the 9211-8i being used to host 8 SATA HDDs. Now, I don't want to brick my LSI my first time flashing, so I wanted to nail down the commands from the guide I linked, but to not include the BIOS portion. Apparently if I clear the LSI controller and power off it will be useless. Would this be the correct order of commands: sas2flsh -o -e 6 sas2flsh -o -f 2118it.bin (the guide says to use this command: sas2flsh -o -f 2118it.bin -b mptsas2.rom) sas2flsh -listall If the commands are correct, then after the sas2flsh -listall I assume my controller will be listed look like this below, with zeros or nothing under x86-BIOS: C:\SAS2FLSH.EXE -listall Adapter Selected is a LSI SAS: SAS2008(B2) Num Ctlr FW Ver NVDATA x86-BIOS PCI Addr ---------------------------------------------------------------------------- 0 SAS2008(B2) 20.00.04.00 14.01.00.08 07.39.00.00 00:01:00:00 Finished Processing Commands Successfully. Exiting SAS2Flash. If all this holds true can I shutdown, move the controller to my unRAID server, attach my SAS to SATA breakout cables, connect my HDDs and boot unRAID OS? Thanks in advance for any confirmations, corrections or advice. Edited September 27, 2018 by KR1SeS Quote Link to comment
JorgeB Posted September 27, 2018 Share Posted September 27, 2018 8 minutes ago, KR1SeS said: Would this be the correct order of commands: Looks OK to me. 8 minutes ago, KR1SeS said: If the commands are correct, then after the sas2flsh -listall I assume my controller will be listed look like this below, with zeros or nothing under x86-BIOS: It will look like this: LSI Corporation SAS2 Flash Utility Version 16.00.00.00 (2013.03.01) Copyright (c) 2008-2013 LSI Corporation. All rights reserved Adapter Selected is a LSI SAS: SAS2008(B2) Num Ctlr FW Ver NVDATA x86-BIOS PCI Addr ---------------------------------------------------------------------------- 0 SAS2008(B2) 20.00.07.00 14.01.00.08 No Image 00:02:00:00 Finished Processing Commands Successfully. Exiting SAS2Flash. 1 Quote Link to comment
KR1SeS Posted September 27, 2018 Author Share Posted September 27, 2018 @johnnie.black thanks, so having No Image for the x86-BIOS won't be an issue or cause the SAS2008 controller to brick when I restart/power off? I assume it will be just fine and it would brick if there was no firmware. Is there a large performance difference having a BIOS image flashed vs not? Quote Link to comment
JorgeB Posted September 27, 2018 Share Posted September 27, 2018 5 minutes ago, KR1SeS said: so having No Image for the x86-BIOS won't be an issue or cause the SAS2008 controller to brick when I restart/power off? No problem, you only need the bios if you want to boot from a device connected to the HBA, if not needed not having one just speeds up the booting process. 1 Quote Link to comment
KR1SeS Posted September 27, 2018 Author Share Posted September 27, 2018 28 minutes ago, johnnie.black said: No problem, you only need the bios if you want to boot from a device connected to the HBA, if not needed not having one just speeds up the booting process. Thanks for the help. I successfully flashed using the commands in my OP. Using '-listall' shows just like your reply, FW Ver: 20.00.07.00 and x86-BIOS: No Image. No I just need to wait to get home from work to test this beauty out! I'll be replacing a Marvel 4 port SATA controller that has been giving me issues. Quote Link to comment
Stroe217 Posted January 17, 2021 Share Posted January 17, 2021 (edited) Hello KR1Ses, I hope this isn't too old of a post but this is the most recent thing I could find to help me with my unraid of the LSI 9211-8i HBA card to IT mode. So following this guide https://nguvu.org/freenas/Convert-LSI-HBA-card-to-IT-mode/ that was mentioned in a older post here I ran into a issue when creating the bootable USB. Not sure if it makes a difference or not but when creating it it didn't contain the files auotexec.bat, command.com, or kernel.sys. I would attach a screenshot of my drive if I could, but I used the rufus tool and followed the guide but not sure if I missed something. Thank you for any help you could provide. Edited January 17, 2021 by Stroe217 Quote Link to comment
PTRFRLL Posted February 5, 2021 Share Posted February 5, 2021 On 1/17/2021 at 4:56 PM, Stroe217 said: Hello KR1Ses, I hope this isn't too old of a post but this is the most recent thing I could find to help me with my unraid of the LSI 9211-8i HBA card to IT mode. So following this guide https://nguvu.org/freenas/Convert-LSI-HBA-card-to-IT-mode/ that was mentioned in a older post here I ran into a issue when creating the bootable USB. Not sure if it makes a difference or not but when creating it it didn't contain the files auotexec.bat, command.com, or kernel.sys. I would attach a screenshot of my drive if I could, but I used the rufus tool and followed the guide but not sure if I missed something. Thank you for any help you could provide. Hopefully you got is figured out by now but I just ran through the same tutorial. Rufus did not add any of those files (autoexec.bat, etc) and it worked just fine. Here's how my flash drive looked: Quote Link to comment
francrouge Posted April 25, 2022 Share Posted April 25, 2022 (edited) Hi guys i know its an old post but how can i put the x86 bios on the card ? if i got the no image message ? thx Edited April 25, 2022 by francrouge Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.