Unraid OS version 6.6.6 available


limetech

Recommended Posts

14 minutes ago, gnollo said:

Done that. On three different browsers, no change.

Sent from my SM-A520F using Tapatalk
 

Perhaps there is something wrong with your flash.

 

Put the boot flash in your PC and make a backup of the config folder.

 

Prepare flash as a new install.

 

Copy config backup to flash,

 

Boot

Link to comment
1 hour ago, gnollo said:

Copied the bz* files across:

bzfirmware bzimage bzmodules bzroot bzroot-gui

Rebooted

Now all I have is the top banner, with an indication of the % disk used.

Any suggestions?

On the flash drive, see if there is /config/dynamix.plg  Delete it, and you're probably good to go after a reboot

  • Upvote 1
Link to comment
4 hours ago, Squid said:

On the flash drive, see if there is /config/dynamix.plg  Delete it, and you're probably good to go after a reboot

Well spotted Squid. There was a dynamix.plg inside the plugins folder within Config. Deleted, rebooted, back in business.

Upon reboot I received the following message: udma crc error count is 4, for drive 6.

Diagnostics attached

tower-diagnostics-20181221-0644.zip

Link to comment
19 minutes ago, trurl said:

Have you tried 8.8.8.8?

Yes I've tried changing it to 8.8.8.8, and when I ping anything from command line I get:

PING google.com (216.58.217.206) 56(84) bytes of data.

From 169.254.160.146 icmp_seq=1 Destination Host Unreachable

 

 

EDIT:

Deleted network.cfg from flash and rebooted. Works now.

Edited by spencers
Link to comment
11 hours ago, spencers said:

Yes I've tried changing it to 8.8.8.8, and when I ping anything from command line I get:

PING google.com (216.58.217.206) 56(84) bytes of data.

From 169.254.160.146 icmp_seq=1 Destination Host Unreachable

 

 

EDIT:

Deleted network.cfg from flash and rebooted. Works now.

..thats an APIPA Adress (Automatic Private IP Adressing)

Link to comment
  • 2 weeks later...
4 minutes ago, bel_din said:

This May help, the last time it locked up. I had a monitor plugged in and it showed something about an irq I'm guessing its not in logs because of the hard resets needed.

A photo from the monitor might also help when it happens again.

 

Yes, diagnostics aren't saved except in Troubleshooting mode, and all logs etc are lost on reboot since all the OS files are in RAM.

Link to comment
1 minute ago, bel_din said:

Will do that. Did you happen to see anything in the logs about plex? It fails to start during boot.

Not really.

 

Did notice some wrong csrf tokens in the syslog. This typically means you left a browser open somewhere when you rebooted.

 

Doesn't look like you have cache. Is this true?

 

 

Link to comment

Hello all,

 

Updated to 6.6.6 from 6.6.5.  I am now unable to stop dockers.  Most containers are linuxserver.io.  Have also tried to stop from cmd line and it does not stop.  Also rolled back to 6.6.5 and no change.  It is possible this started before the upgrade and I just haven't had to manually stop a docker in a month or two. 

 

Did some searching and didn't find much.  Not sure this is related to the unRAID version or some other issue.  Diags attached.  Many thanks for any assistance.

 

 

landfill-diagnostics-20190102-1851.zip

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.