mikedpitt420 Posted January 10, 2019 Share Posted January 10, 2019 Just purchased a Supermicro 836 case, Supermicro X10SRH-CLN4f board, Intel Xeon E5 2630. Supermicro RAM as well. I have just booted it up, and it fails to see almost every disk I have. I have an LSI card (that was flashed, I had thought but now am seeing BIOS again) with 2 mini sas connectors going to 2 of the mini sas connectors on the backplanes in the case. The other two mini sas backplanes I just have hooked up to cables that make them split to 4 SATA connectors each, which are all plugged directly into the motherboard, and 2 SSDs (old and new cache) both also plugged directly into the motherboard, not using the backplane. The system can see the 2 SSDs plugged directly into the motherboard, and 4 of the ones in the backplane and it seems completely random. I have attached my diagnostics. Can anyone help me with this? tower-diagnostics-20190110-0545.zip Quote Link to comment
Vr2Io Posted January 10, 2019 Share Posted January 10, 2019 Likely common forward and reverse cable issue. Quote Link to comment
mikedpitt420 Posted January 10, 2019 Author Share Posted January 10, 2019 I'm sorry. I don't know what that is. Can you elaborate a bit? Quote Link to comment
Vr2Io Posted January 10, 2019 Share Posted January 10, 2019 (edited) Sorry, there should only one kind of miniSAS to miniSAS cable, does all connect tight ? Each miniSAS connect 4 device, so I suppose 2 miniSAS between LSI and backplane could found 8 device. The other eight device provide by Mobo, 2 reverse miniSAS-to-SATA need. Edited January 10, 2019 by Benson Quote Link to comment
mikedpitt420 Posted January 10, 2019 Author Share Posted January 10, 2019 (edited) Yes. But I am thinking the issue may be that I shouldn't have plugged a mini SAS cable from the backplane to 4 sata slots on the motherboard. I think I may have burned out the board. I just ordered another motherboard and another lsi 8 drive card so everything is mini sas to mini sas. Edited January 10, 2019 by mikedpitt420 Quote Link to comment
Vr2Io Posted January 10, 2019 Share Posted January 10, 2019 (edited) 12 minutes ago, mikedpitt420 said: But I am thinking the issue may be that I shouldn't have plugged a mini SAS cable from the backplane to 4 sata slots on the motherboard. I think I may have burned out the board. Yes, a mistake, but usually won't burn anything ( there are no any power signal in miniSAS-SATA cable ). BTW wried for randon drive recognize result. Edited January 10, 2019 by Benson Quote Link to comment
mikedpitt420 Posted January 10, 2019 Author Share Posted January 10, 2019 (edited) Oh it did. Small wisp of smoke and now the board won't boot. Smoke came directly from where the sata cables were plugged in Edited January 10, 2019 by mikedpitt420 Quote Link to comment
Vr2Io Posted January 10, 2019 Share Posted January 10, 2019 2 minutes ago, mikedpitt420 said: Oh it did. Small wisp of smoke and now the board won't boot. Smoke came directly from where the sata cables were plugged in You mean the minSAS-SATA cable ? Quote Link to comment
mikedpitt420 Posted January 10, 2019 Author Share Posted January 10, 2019 Yes where the mini SAS to a SATA cables smoked for a second at the board. Now it wont boot and there is visible char marks around those ports on the board Quote Link to comment
Vr2Io Posted January 10, 2019 Share Posted January 10, 2019 (edited) 3 minutes ago, mikedpitt420 said: Yes where the mini SAS to a SATA cables smoked for a second at the board. Now it wont boot and there is visible char marks around those ports on the board Still don't understand why burn, btw, lucky not burn on backplane. 😭 Edited January 10, 2019 by Benson Quote Link to comment
mikedpitt420 Posted January 10, 2019 Author Share Posted January 10, 2019 Mini sas has a higher signaling voltage than sata. I suspect that's what happened....should have known not to do that Quote Link to comment
Vr2Io Posted January 10, 2019 Share Posted January 10, 2019 (edited) 5 minutes ago, mikedpitt420 said: Mini sas has a higher signaling voltage than sata. I suspect that's what happened....should have known not to do that Yes, but those a small signal, if I am correct those are 0.3v / 0.6v and controller/device end have small capacitor in series to block DC level. Anyway no idea for the burn. Pls take care on the backplane, the burning power should come from backplane instead of Mobo. Edited January 10, 2019 by Benson Quote Link to comment
mikedpitt420 Posted January 10, 2019 Author Share Posted January 10, 2019 Just hope the drives are ok.... Quote Link to comment
Vr2Io Posted January 10, 2019 Share Posted January 10, 2019 (edited) Deleted. Good luck. Edited January 10, 2019 by Benson Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.