March 23, 20197 yr Author On 3/21/2019 at 7:00 AM, johnnie.black said: Shouldn't make any difference. I suspect there's something on the current config causing problems, hence the suggestion to redo the flash drive and start over. It did not work. When I started the array, it got stuck again at "Starting services". This time I didn't even touch the docker or vm manager.
March 24, 20197 yr Author 19 hours ago, johnnie.black said: Try to grab the diags on the console. My cache and drives are encrypted. Would I be fine to enter my encryption key then start the array while the server is not using https? Or should I enable https first before I starting the array?
March 24, 20197 yr Author 20 hours ago, johnnie.black said: Try to grab the diags on the console. Here is the diag tower-diagnostics-20190324-0448.zip
March 24, 20197 yr Community Expert You are still getting these errors: Mar 24 04:32:00 Tower rpcbind[3782]: connect from 10.0.7.23 to getport/addr(mountd) Mar 24 04:32:00 Tower rpcbind[3783]: connect from 10.0.7.23 to getport/addr(mountd) Mar 24 04:32:00 Tower rpcbind[3784]: connect from 10.0.7.23 to getport/addr(mountd) Mar 24 04:32:00 Tower rpcbind[3785]: connect from 10.0.7.23 to getport/addr(mountd) Mar 24 04:32:00 Tower rpcbind[3786]: connect from 10.0.7.23 to getport/addr(mountd) Mar 24 04:32:00 Tower rpcbind[3787]: connect from 10.0.7.23 to getport/addr(mountd) No idea what they are, but since you're still getting them with a new flash config it's likely related to your problems.
March 24, 20197 yr Author You are still getting these errors: Mar 24 04:32:00 Tower rpcbind[3782]: connect from 10.0.7.23 to getport/addr(mountd)Mar 24 04:32:00 Tower rpcbind[3783]: connect from 10.0.7.23 to getport/addr(mountd)Mar 24 04:32:00 Tower rpcbind[3784]: connect from 10.0.7.23 to getport/addr(mountd)Mar 24 04:32:00 Tower rpcbind[3785]: connect from 10.0.7.23 to getport/addr(mountd)Mar 24 04:32:00 Tower rpcbind[3786]: connect from 10.0.7.23 to getport/addr(mountd)Mar 24 04:32:00 Tower rpcbind[3787]: connect from 10.0.7.23 to getport/addr(mountd) No idea what they are, but since you're still getting them with a new flash config it's likely related to your problems.I'm not a sysadmin by trade but I think that has nothing to do with the problem. That IP address is my Proxmox server. I have this server to connect to my unRaid via NFS. I have some shares that my Proxmox uses. I would assume that if the array is not enabled, I would get this error because the Proxmox server is trying to connect to these shares that I have.Here is the link to Proxmox https://www.proxmox.com/en/proxmox-veI don't get that error while I'm in 6.5.3 because I can get the array to start with no problem.I don't have problem upgrading because the server boots at whatever version I run. The issue is unRaid could not get any services to start completely. The last diag could not get the array to start at all. If I copied my /config, I could start the array, but could not get docker and VM manager to start. Sent from my ONEPLUS A6003 using Tapatalk
March 24, 20197 yr Community Expert Sorry, no more ideas then, don't see any reason on the syslog for both docker and VM services failing to start.
March 24, 20197 yr Author 8 hours ago, johnnie.black said: Sorry, no more ideas then, don't see any reason on the syslog for both docker and VM services failing to start. Should I start from scratch and rebuild my unraid server again? If I should start from scratch, can I still load my VMs and Docker containers from my current install? My HDDs and cache drive are encrypted, would I get some issues with a brand new install? The thing is if I were to build from scratch, was this the same method we just tried from the last diag? Am I stuck in 6.5.3?
March 25, 20197 yr Author 5 minutes ago, trurl said: Is your BIOS up-to-date? According to IPMI Firmware Revision : 03.60 Firmware Build Time : 07/28/2017BMC BIOS Version: 1.0b BIOS Build Time: 12/12/2017 Redfish Version : 1.0.1
March 25, 20197 yr Community Expert 10 hours ago, pingmanping said: If I should start from scratch, can I still load my VMs and Docker containers from my current install? We already tried this, except for using the existing super.dat, but that should't change anything, one thing I didn't ask, if you just start one of the services, either one first, does it also get stuck, i.e., are both failing to start individually? 10 hours ago, pingmanping said: My HDDs and cache drive are encrypted, would I get some issues with a brand new install? No, just use existing key/passfrase
Archived
This topic is now archived and is closed to further replies.