Drive reporting Smart Errors but cannot find them?


mbc0

Recommended Posts

Hi,

 

I just bought a drive very cheaply advertised as new unopened from ebay (trusted seller) but found it opened and when checking with Seagate there is no warranty on the drive as it was sold through the recertified sales program.  however as it was cheap I thought I *May* keep it and run a smart test to see what it was like.  unRAID tells me there are smart errors and to download the report but I cannot see anything obvious? the overall smart test passes as well... can anyone see what the problem may be please?

 

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST6000NM0095
Revision:             E004
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   512 bytes
Physical block size:  4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500b706d54f
Serial number:        ZAD19X8H0000C7364F19
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Oct  2 13:20:30 2019 BST
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Grown defects during certification <not available>
Total blocks reassigned during format <not available>
Total new blocks reassigned <not available>
Power on minutes since format <not available>
Current Drive Temperature:     26 C
Drive Trip Temperature:        60 C

Manufactured in week 29 of year 2019
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  60
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  62
Elements in grown defect list: 0

Vendor (Seagate Cache) information
  Blocks sent to initiator = 78352
  Blocks received from initiator = 4183288
  Blocks read from cache and sent to initiator = 10183
  Number of read and write commands whose size <= segment size = 430
  Number of read and write commands whose size > segment size = 5

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 0.70
  number of minutes until next internal SMART test = 41

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:      82830        0         0     82830          0          0.039           0
write:         0        0         0         0          0          2.148           0
verify:      406        0         0       406          0          0.001           0

Non-medium error count:        0


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -       0                 - [-   -    -]

Long (extended) Self-test duration: 38632 seconds [643.9 minutes]

Background scan results log
  Status: no scans active
    Accumulated power on time, hours:minutes 0:42 [42 minutes]
    Number of background scans performed: 0,  scan progress: 0.00%
    Number of background medium scans performed: 0

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: loss of dword synchronization
    reason: power on
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000c500b706d54d
    attached SAS address = 0x5001e677b86e5fff
    attached phy identifier = 15
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500b706d54e
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.