SOLVED: I'm dumb...Supermicro X9DRi-F using LACP...one port is always 100Mbps?


Recommended Posts

Solved: I swear I had messed with all cable and port combinations, however, I grabbed another cable and they are both at 1000Mbps now.

 

Has anyone ever seen this before?

 

I can swap cable as well as ports and I always have 1 port as 1000Mbps and 1 as 100Mbps.  Both ports seem to work at 1000Mbps but no combination of cables or switch ports will make them both be 1000Mbps.

 

I also noticed that with my Cisco SG250-26 switch it always lists 1 port as Standy Member with LACP enabled in both the switch and the UnRAID.  If I take the switch off of LACP (ie Static) then it puts both ports as Active Member but 1 of them is still 100Mbps.  UnRAID doesn't like that configuration though.

 

UnRAID shows 1 as being 1000Mbps and 1 as 100Mbps regardless of whether I have a bond configured.

 

I've restarted as well.

 

root@Tower:~# ethtool eth0
Settings for eth0:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full 
                                100baseT/Half 100baseT/Full 
                                1000baseT/Full 
        Supported pause frame use: Symmetric
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full 
                                100baseT/Half 100baseT/Full 
                                1000baseT/Full 
        Advertised pause frame use: Symmetric
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: off (auto)
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000007 (7)
                               drv probe link
        Link detected: yes
root@Tower:~# ethtool eth1
Settings for eth1:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full 
                                100baseT/Half 100baseT/Full 
                                1000baseT/Full 
        Supported pause frame use: Symmetric
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full 
                                100baseT/Half 100baseT/Full 
                                1000baseT/Full 
        Advertised pause frame use: Symmetric
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 100Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: off (auto)
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000007 (7)
                               drv probe link
        Link detected: yes

 

 

Edited by jlficken
Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.