Jump to content
jebusfreek666

Upgrading build. Looking for case and cage suggestions.

9 posts in this topic Last Reply

Recommended Posts

Currently running a define R5. It houses 2 SSD, and 11 HDD (dual parity, 9 data). I am in the process of upgrading the drives to larger capacity, but thought I might as well upgrade the case for more storage options down the road as well. I would really like to change out to hot swap bays instead, and would like to have more than I currently have available. I think it would be nice to have the 2 parity drives internal so I don't mess them up, but all data drives hot swap if that is possible. I saw in previous posts from a few years ago that people were suggesting and antec 900 case with 3 of the supermicro CSE-M35T-1B 5-in-3 cages. Is this still the recommendation? Ideally, I would like to have room for 4 of the cages, but I could probably make due with 3. It seems that both this case and the cages are old hardware as I can't even find the cage on ebay. I have found it on newegg and amazon, but it looks like its 3rd party sellers. So I am guessing supermicro has discontinued this in favor of a newer model? 

 

So the breakdown of what I am looking for is as follows:

Space to fit at least (3) 5-in-3 hot swap cages, but preferably (4)

Internal space to also fit 2 HDD for dual parity

Internal space for 2 SSD for cache

Something as quiet as possible

Something with filters if possible

Any other features you can think of that I may need. This is only my second build....

 

Thanks guys.

Share this post


Link to post

If you can find it, the Antec 1900 (in my sig) has quite a bit of room. It's the case I use and I have 20 drives in it. I think I could configure it for more if I really wanted to get creative. It is very quiet (imo), has filters, but is not hot-swap.

Edited by whipdancer

Share this post


Link to post
7 hours ago, whipdancer said:

If you can find it, the Antec 1900 (in my sig) has quite a bit of room. It's the case I use and I have 20 drives in it. I think I could configure it for more if I really wanted to get creative. It is very quiet (imo), has filters, but is not hot-swap.

Thanks for the suggestion. But the hot swap capability is one aspect that I want the most,

Share this post


Link to post

Silverstone cs380b with a SST-FS303B in the 5.25 inch bays.

 

I considered it, but didn't want to compromise on cooling and so went for the R5 with the SST-FS303B which gives me 11 bays.

Share this post


Link to post
3 minutes ago, Spies said:

Silverstone cs380b

I have this case and did the case mods recommended by dmacias which improved things greatly.  I put that here for anyone else coming across this thread.

 

It looks like you found something that works well for you.  👍

Share this post


Link to post

Might be better to get a case with 5.25 inch bays top to bottom and then just fill it with the 3 in 2x5.25 bays.

Share this post


Link to post
3 minutes ago, Spies said:

Might be better to get a case with 5.25 inch bays top to bottom and then just fill it with the 3 in 2x5.25 bays.

Those are rare these days.  They are much harder to find than just a couple of years ago. 

 

I went with the CS380 because it has front-accessible hot-swap bays (without the expense of a bunch of add-in hot-swap cages) and I put a 4xSSD hot-swap in one of the two 5.25 slots.  It works for me but it works A LOT better after the mods 😁

Share this post


Link to post
27 minutes ago, Spies said:

Might be better to get a case with 5.25 inch bays top to bottom and then just fill it with the 3 in 2x5.25 bays.

This is kind of what I am looking for, but finding one seems to be an issue. I am even ok with the cube design, but can't seem to locate one with sufficient external 5.25 bays.

Share this post


Link to post
On 11/8/2019 at 4:01 PM, jebusfreek666 said:

This is kind of what I am looking for, but finding one seems to be an issue. I am even ok with the cube design, but can't seem to locate one with sufficient external 5.25 bays.

I've seen 1 offered used on Facebook market place and it was gone before I could inquire about it.

I'm under the impression there may be a couple of new models offered like that but they are not available in the US generally (I think I found one offered in Australia?). Unless I stumble across one randomly, I've pretty much given up on the idea of the particular solution.

I have considered looking at a duplicator tower and seeing what could be done with one of those.

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.