mspencerl87 Posted December 9, 2019 Share Posted December 9, 2019 Anything i can do? See reddit post. Is this a Kernel issue, Mobo issue, or Ryzen issue? See below, how can i generate drivers.conf? Added 'modprob nct6775 0xd352 to go file. added sensors.conf to plugin folder #sensors chip "k10temp-pci-00c3" label temp1 "MB Temp" label temp2 "CPU Temp" i ran sensors-detect and got Trying family `VIA/Winbond/Nuvoton/Fintek'... Yes Found unknown chip with ID 0xd352 Then ran "sensors" and got: modprobe nct6775 0xd352^C and got k10temp-pci-00c3 Adapter: PCI adapter Tdie: +47.4°C (high = +70.0°C) Tctl: +57.4°C nct6795-isa-0a20 Adapter: ISA adapter Vcore: +1.42 V (min = +0.00 V, max = +1.74 V) in1: +1.02 V (min = +0.00 V, max = +0.00 V) ALARM AVCC: +3.34 V (min = +0.00 V, max = +0.00 V) ALARM +3.3V: +3.38 V (min = +0.00 V, max = +0.00 V) ALARM in4: +1.01 V (min = +0.00 V, max = +0.00 V) ALARM in5: +0.15 V (min = +0.00 V, max = +0.00 V) ALARM in6: +0.74 V (min = +0.00 V, max = +0.00 V) ALARM 3VSB: +3.33 V (min = +0.00 V, max = +0.00 V) ALARM Vbat: +3.25 V (min = +0.00 V, max = +0.00 V) ALARM in9: +1.82 V (min = +0.00 V, max = +0.00 V) ALARM in10: +0.00 V (min = +0.00 V, max = +0.00 V) in11: +0.74 V (min = +0.00 V, max = +0.00 V) ALARM in12: +1.16 V (min = +0.00 V, max = +0.00 V) ALARM in13: +0.68 V (min = +0.00 V, max = +0.00 V) ALARM in14: +1.51 V (min = +0.00 V, max = +0.00 V) ALARM fan1: 0 RPM (min = 0 RPM) fan2: 2428 RPM (min = 0 RPM) fan3: 1165 RPM (min = 0 RPM) fan4: 830 RPM (min = 0 RPM) fan5: 836 RPM (min = 0 RPM) fan6: 849 RPM (min = 0 RPM) SYSTIN: +33.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = CPU diode CPUTIN: +39.0°C (high = +110.0°C, hyst = +90.0°C) sensor = thermistor AUXTIN0: +41.0°C (high = +110.0°C, hyst = +90.0°C) sensor = thermistor AUXTIN1: -128.0°C sensor = thermistor AUXTIN2: +40.0°C sensor = thermistor AUXTIN3: -1.0°C sensor = thermistor SMBUSMASTER 0: +57.5°C PCH_CHIP_CPU_MAX_TEMP: +0.0°C PCH_CHIP_TEMP: +0.0°C PCH_CPU_TEMP: +0.0°C intrusion0: ALARM intrusion1: ALARM beep_enable: disabled Link to comment
trurl Posted December 9, 2019 Share Posted December 9, 2019 You can go directly to the correct support thread for any of your plugins by selecting its Support link on the Plugins page in the webUI. Link to comment
mspencerl87 Posted December 10, 2019 Author Share Posted December 10, 2019 (edited) The support link redirects to But there is no where to post? Do you have a link to create support post? Edited December 10, 2019 by mspencerl87 Link to comment
trurl Posted December 10, 2019 Share Posted December 10, 2019 Locking this thread since the user has found the support thread. Link to comment
Recommended Posts