chiphayes Posted August 13, 2007 Share Posted August 13, 2007 I'm upgrading my UnRaid to all SATA drives. In doing so, I replaced my Asus P5PE-VM board with the P5B-VM DO that Lime uses. I can't seem to get the USB to boot on the new system. Does anyone have a listing of the proper BIOS settings to use on this board? Thanks, Chip Quote Link to comment
Billped Posted August 14, 2007 Share Posted August 14, 2007 I don't have the exact same board, but ... The big item for me was to set the USB key as FDD (not HDD, floppy, or auto). Cheers, Bill Quote Link to comment
chiphayes Posted August 14, 2007 Author Share Posted August 14, 2007 Billped... Thanks for that tip. That helped me get it to boot up. I also had to configure SATA #1 as [AHCI] as well in order to get it to go. Now my problem is I can't get more than the first two drives to be recognized by the new board. I've got six SATA drives at the moment, and only SATA 1 and 2 off the main board are being recognized. The other four ports on the motherboard don't seem to want to recognize any drives plugged into them. I have a feeling this is more BIOS tweakage that's needed. TIme to dive into the user guide on this thing (unless Tom has a suggestion or two... hint hint). Thanks! Chip Quote Link to comment
chiphayes Posted August 14, 2007 Author Share Posted August 14, 2007 Okay... didn't need to set SATA #1 to AHCI after all. IDE works fine. And the problem with the other drives was a problem with the icy docks not seating properly. Thanks for the help... onward and upward now.... Quote Link to comment
cmhardwick Posted August 14, 2007 Share Posted August 14, 2007 setting the SATA to IDE will hamper your performance if I remember some other posts here. I'd leave it set to AHCI. Quote Link to comment
Fountainhead Posted August 15, 2007 Share Posted August 15, 2007 Hey Chiphayes...when you get it all up and running smoothly could you run down the BIOS settings that you used, or at least the ones that you changed from their default settings? I'm considering this board for a new build. Thanks. Quote Link to comment
chiphayes Posted August 15, 2007 Author Share Posted August 15, 2007 Fountainhead... Okay, it all seems to be running smoothly. Here are the pertinent BIOS settings (CAVEAT: I messed around with a bunch of these. While it's working fine under these settings, I may have changed some that didn't need changing.) IDE Configuration SATA#1 Configuration [Enhanced] Configure SATA#1 as [AHCI} USB Configuration USB Functions [Enabled] Legacy USB Support [Enabled] Port 64/60 Emulation [Disabled] USB 2.0 Controller Mode [HiSpeed] BIOS EHCI Hand-off [Enabled] USB Mass Storage Device Configuration (My USB stick shows up twice, which was the case with my last set-up) Set both Devices Emulation Types as [Forced FDD] Boot Settings Boot Device Priority 1st Boot Device [uSB SanDisk...] Removable Drives 1st Drive [uSB Sandisk...] 2nd Drive [uSB Sandisk...] I also disabled the on-board sound. I'll holler in here if I discover any of this is either a mistake, or somehow hampers performance of the system. Chip Quote Link to comment
Fountainhead Posted August 15, 2007 Share Posted August 15, 2007 Thanks a lot Chiphayes. I've got this MB, along with some RAM and a cpu in my Newegg cart just waiting for me to check out. Probably within a couple of days. Quote Link to comment
Michael Posted August 23, 2007 Share Posted August 23, 2007 Tom-- Can you confirm/deny Chip's settings? Better yet, can you create a page similar to this for the P5B-VM DO? http://www.lime-technology.com/wordpress/?page_id=14 I normally wouldn't request this, but I know a lot of us are using the same motherboard as your new builds for the best chance of compatibility. Michael Quote Link to comment
limetech Posted August 26, 2007 Share Posted August 26, 2007 Yeah I have to get around to doing that. Your settings look ok. We also disable ieee1394, serial, parallel support. You should not see your Flash listed twice - never seen that before. Make sure you're using the latest bios. BTW, all you have to do is download the bios file onto your Flash and then use the motherboard bios update utility - works great. Setting on-board SATA to AHCI or IDE works. We have noticed that in AHCI mode the Hitachi 7K1000 (1TB) hard drives are not always detected from a cold power-up - no problem with other drive types. Very strange. We sent a message off to Asus telling them about a "cold start AHCI detection bug" so perhaps this will get fixed in a new bios release. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.