bonienl Posted January 21, 2020 Share Posted January 21, 2020 (edited) 17 minutes ago, Markus Riekki said: Do not know if issue is new with 6.8.1 but docker port mappings does not work/show correctly Port mappings are only relevant when BRIDGE network is used. Other network types give unrestricted access to the container ports. If you need help, please post under the support topic Edited January 21, 2020 by bonienl Quote Link to comment
Markus Riekki Posted January 21, 2020 Share Posted January 21, 2020 3 minutes ago, bonienl said: Port mappings are only relevant when BRIDGE network is used. Other network types give unrestricted access to the container ports. Updated to bridge and this is correct. Also screens show correctly. Host mode port usage and comparison is quite hard as used ports are not in lists of used ports Quote Link to comment
bonienl Posted January 21, 2020 Share Posted January 21, 2020 7 minutes ago, Markus Riekki said: Host mode port usage and comparison is quite hard as used ports are not in lists of used ports Because host mode doesn't know port mapppings. Quote Link to comment
Markus Riekki Posted January 21, 2020 Share Posted January 21, 2020 13 minutes ago, bonienl said: Because host mode doesn't know port mapppings. Plex container does not have any parameters so in bridge mode it does not show any up:port mappings on docker page. However when running host this mapping is shown so that I know which unraid port data is consumed by this docker image Quote Link to comment
bonienl Posted January 21, 2020 Share Posted January 21, 2020 The plex container has "exposed" ports configured and these are shown when the host network is selected. If the container does not have port mappings defined in its XML, it will not work in bridge mode, unless these port mappings are added manually. Quote Link to comment
jbartlett Posted January 22, 2020 Share Posted January 22, 2020 FWIW, I got the crash screen a couple times that many others have posted, typically after a cold boot after I moved some hardware around. It booted fine after hitting the RESET button. Quote Link to comment
TheMannequin Posted January 22, 2020 Share Posted January 22, 2020 Updated from 6.7.2. Only issue was that my Pulseway agent did not start correctly.... downloaded the newest agent version and removed symlinks from go file as per updated instructions here on the forum. After another reboot, all ok again. Quote Link to comment
Harro Posted January 22, 2020 Share Posted January 22, 2020 Upgraded 2 servers and all went fine. Thank you for your continue support. Quote Link to comment
sonofdbn Posted January 23, 2020 Share Posted January 23, 2020 On 1/14/2020 at 11:04 PM, sonofdbn said: Is anyone else experiencing slower copy speeds? Previously I was on 6.5.3 and upgraded to 6.7.2, but went back to 6.5.3 because copying speeds from my SSD cache drive to the array went down substantially: from about 74 MB/s to 52 MB/s. Now I've upgraded from 6.5.3 to 6.8.1 and unfortunately am experiencing the same slow copy speeds (in fact possibly even slightly slower). Still wondering if this is just me. Or is this a known issue or some setting I should change? Quote Link to comment
ur6969 Posted January 23, 2020 Share Posted January 23, 2020 On 1/17/2020 at 9:37 PM, Yak said: Upgraded with no trouble at all, some weirdness with terminal windows in Firefox, but that's more likely to be the 8 million privacy extensions I've got running. So, yeah, it's good EDIT: Fixed it. Just needed to grant permission for the terminal window to 'Extract Canvas Data' THANK YOU! I couldn't figure the terminal thing out! Quote Link to comment
jaylo123 Posted January 23, 2020 Share Posted January 23, 2020 On 1/11/2020 at 2:42 AM, cybrnook said: Thank you and the team for all the hard work lately! Yes. Thank you! Quote Link to comment
darrenyorston Posted January 24, 2020 Share Posted January 24, 2020 On 1/18/2020 at 7:37 AM, Yak said: Upgraded with no trouble at all, some weirdness with terminal windows in Firefox, but that's more likely to be the 8 million privacy extensions I've got running. So, yeah, it's good EDIT: Fixed it. Just needed to grant permission for the terminal window to 'Extract Canvas Data' What was the problem you were experiencing? I generally use Firefox and noted that I cant see any text when I open the terminal window from the menu bar. There is text there because when I do CTRL+A CTRL+C I can paste into a text document. Is that the problem you're having? If so where did you make the change to get it to work? Quote Link to comment
mifronte Posted January 24, 2020 Share Posted January 24, 2020 (edited) Just upgraded to 6.8.1 from 6.7.2. After reboot, the server frozed at the login prompt and I couldn't access the GUI nor login via the command prompt using IPMI. So I hard rebooted again. I can now login at the login prompt via IPMI, but still cannot access the GUI or via telnet. I cannot access my shares through Windows either. I also noticed the IPv4 address at the login prompt is not correct. I don't know where it got that IP address. Please advice. Update __________________ Sent a Ctrl+Alt+Del via IPMI and let the server rebooted again. This time the correct IPv4 address is shown at the login prompt and I can now access the GUI. First time since v4.7 that I had trouble upgrading. Hopefully all is well. Edited January 24, 2020 by mifronte Quote Link to comment
JorgeB Posted January 24, 2020 Share Posted January 24, 2020 25 minutes ago, mifronte said: I also noticed the IPv4 address at the login prompt is not correct. I don't know where it got that IP address. Likely a flash drive problem, backup flash's config folder, redo flash drive and restore config folder. Quote Link to comment
Yak Posted January 24, 2020 Share Posted January 24, 2020 (edited) 10 hours ago, darrenyorston said: What was the problem you were experiencing? I generally use Firefox and noted that I cant see any text when I open the terminal window from the menu bar. There is text there because when I do CTRL+A CTRL+C I can paste into a text document. Is that the problem you're having? If so where did you make the change to get it to work? Yep, a new terminal window was blank on opening. In the terminal window click on the permissions icon (LH side of the address bar just before the IP address, the padlock and two lines) Then allow 'Extract Canvas Data' (Firefox attempts to stop canvas fingerprint tracking) and all should be good. You can also click on the shield icon and disable Enhanced Tracking Protection for your Unraid server Edited January 24, 2020 by Yak Quote Link to comment
TheMannequin Posted January 24, 2020 Share Posted January 24, 2020 (edited) Only noticed this now.... on the Dashboard view, CPU 0 is pegged at 100% usage.....but Stats and top shows that the usage is normal...? EDIT: I stopped all VM's and Dockers, but still shows CPU 0 at 100% usage.... Edited January 24, 2020 by TheMannequin added EDIT: Quote Link to comment
argonaut Posted January 24, 2020 Share Posted January 24, 2020 17 hours ago, darrenyorston said: What was the problem you were experiencing? I generally use Firefox and noted that I cant see any text when I open the terminal window from the menu bar. There is text there because when I do CTRL+A CTRL+C I can paste into a text document. Is that the problem you're having? If so where did you make the change to get it to work? Firefox since at least version 57 (much longer for sure) has had an issue with black text on black background fields in some CSS elements. I know this happens in Gnome, xfce and KDE. It is much worse if you have a dark theme enabled. I don't use Windows so I don't know about that OS. It can be mitigated via a CSS tweak. The Firefox developers say that this is not an issue due to pages written purely in CSS, not due to a Firefox bug, if you consider native input styles to be a feature rather than a bug. See https://bugzilla.mozilla.org/show_bug.cgi?id=1283086 Quote Link to comment
zoggy Posted January 24, 2020 Share Posted January 24, 2020 (edited) 2 hours ago, TheMannequin said: Only noticed this now.... on the Dashboard view, CPU 0 is pegged at 100% usage.....but Stats and top shows that the usage is normal...? EDIT: I stopped all VM's and Dockers, but still shows CPU 0 at 100% usage.... you can see your load is 1.x which aligns with one of the cpus being pegged. your not showing all the processes in top.. try: top -b1 Edited January 24, 2020 by zoggy Quote Link to comment
Tucubanito07 Posted January 24, 2020 Share Posted January 24, 2020 Did anyone else have issues with Plex when updated t0 6.8.1? I updated last night and kept telling me Execution Error and did not want to restart. I then restore from the back up on 6.8.1 and same. I downgraded to 6.8.0 and is working like normal. Any help is appreciated. Quote Link to comment
sparkus Posted January 24, 2020 Share Posted January 24, 2020 @Tucubanito07 might be the same error that @fatalfurry and I reported earlier. nobody from unraid has really responded to it. Quote Link to comment
Tucubanito07 Posted January 24, 2020 Share Posted January 24, 2020 5 minutes ago, sparkus said: @Tucubanito07 might be the same error that @fatalfurry and I reported earlier. nobody from unraid has really responded to it. I dont see where he states he is having issues with Plex. I see he was having issues with C-States. I was able to get in and everything seems to be working on 6.8.1 for me. Plex did not start and and after manually trying to start it, it would say Execution Failed. On 6.8.1 i did a restore and still the same issues. Then, i did a downgrade to 6.8.0 and Plex started to work again. Just weird. I never have issues upgrading before. Which is fine i know unraid will get to the bottom of it. Thanks @sparkus Quote Link to comment
sparkus Posted January 24, 2020 Share Posted January 24, 2020 Ha @Tucubanito07 I apparently didn't read well. Sorry to have thrown you off the track. Quote Link to comment
Tucubanito07 Posted January 24, 2020 Share Posted January 24, 2020 3 minutes ago, sparkus said: Ha @Tucubanito07 I apparently didn't read well. Sorry to have thrown you off the track. No problem at all. Thank you anyways. Quote Link to comment
Paul_Ber Posted January 24, 2020 Share Posted January 24, 2020 On 1/11/2020 at 9:54 AM, bonienl said: Check and fix your USB stick for file system corruptions Any tips on faster USB sticks? Or does UNraid normally take forever to boot? Using a Cruzer_Fit 8GB now or at least for 5 years or so. Quote Link to comment
Frank1940 Posted January 24, 2020 Share Posted January 24, 2020 1 minute ago, Paul_Ber said: Or does UNraid normally take forever to boot? You should first look at the boot process as I believe the bz* are either (1) copied and unzipped or (2) unzipped directly to memory. (But before that happens any BIOS's any add-in cards have to initialized.) Then the installation process starts in earnest. I said installation as Unraid is installed every time, you restart the server. You can see when the reading of most of the information has been read from the flash drive when the screen starts to display the installation steps. The flash drive will now only be read to get the configuration data and plugin installation information. So put a stop watch to the boot process and see what percentage of the time (it is right at the bottom of the screen), the flash drive is actually being read. Now, I am going to tell a story about my first Unraid server. The BIOS on that very old AMD MB only had drivers for USB1. It took foreeevvvver to load the bz* files to memory (minutes) and a few seconds to finish the install. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.