CHINCB Posted February 16, 2020 Share Posted February 16, 2020 Based on the Raw_Read_Error_Rate is this dive destined for the recyciling bin? Quote smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.98-Unraid] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Serial Number: WD-WMC4N2898941 LU WWN Device Id: 5 0014ee 0592a2c03 Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Feb 16 08:58:29 2020 SAST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 113) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (38940) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 391) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 3987 3 Spin_Up_Time POS--K 194 173 021 - 5275 4 Start_Stop_Count -O--CK 087 087 000 - 13821 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 047 047 000 - 39382 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 307 192 Power-Off_Retract_Count -O--CK 200 200 000 - 203 193 Load_Cycle_Count -O--CK 183 183 000 - 51858 194 Temperature_Celsius -O---K 119 094 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 4393 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4393 [0] occurred at disk power-on lifetime: 39212 hours (1633 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b2 8e 26 98 40 00 Error: UNC at LBA = 0xb28e2698 = 2995660440 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 b8 00 20 00 00 b2 8e 62 30 40 08 05:55:03.649 READ FPDMA QUEUED 60 00 88 00 18 00 00 b2 8e 61 a8 40 08 05:55:03.644 READ FPDMA QUEUED 60 02 e0 00 10 00 00 b2 8e 5e c8 40 08 05:55:03.640 READ FPDMA QUEUED 60 02 80 00 f8 00 00 b2 8e 5c 48 40 08 05:55:03.638 READ FPDMA QUEUED 60 02 c0 00 e8 00 00 b2 8e 59 88 40 08 05:55:03.635 READ FPDMA QUEUED Error 4392 [23] occurred at disk power-on lifetime: 39212 hours (1633 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b2 8e 1c 68 40 00 Error: UNC at LBA = 0xb28e1c68 = 2995657832 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 a8 00 30 00 00 b2 8e 26 e0 40 08 05:55:00.074 READ FPDMA QUEUED 60 01 28 00 28 00 00 b2 8e 25 b8 40 08 05:55:00.072 READ FPDMA QUEUED 60 04 18 00 20 00 00 b2 8e 21 a0 40 08 05:55:00.072 READ FPDMA QUEUED 60 05 38 00 18 00 00 b2 8e 1c 68 40 08 05:55:00.072 READ FPDMA QUEUED 60 04 b8 00 10 00 00 b2 8e 36 e8 40 08 05:55:00.051 READ FPDMA QUEUED Error 4391 [22] occurred at disk power-on lifetime: 39212 hours (1633 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b2 8e 1c 30 40 00 Error: UNC at LBA = 0xb28e1c30 = 2995657776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 88 00 c8 00 00 b2 8e 3b a0 40 08 05:54:56.270 READ FPDMA QUEUED 61 00 88 00 c0 00 00 b2 8e 1b a0 40 08 05:54:56.270 WRITE FPDMA QUEUED 60 04 b8 00 b8 00 00 b2 8e 36 e8 40 08 05:54:56.270 READ FPDMA QUEUED 60 00 40 00 20 00 00 b2 8e 1c 28 40 08 05:54:56.269 READ FPDMA QUEUED 60 05 38 00 18 00 00 b2 8e 1c 68 40 08 05:54:56.269 READ FPDMA QUEUED Error 4390 [21] occurred at disk power-on lifetime: 39212 hours (1633 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b2 8e 1b a0 40 00 Error: UNC at LBA = 0xb28e1ba0 = 2995657632 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 80 00 a8 00 00 b2 8e 31 88 40 08 05:54:52.651 READ FPDMA QUEUED 60 02 c0 00 a0 00 00 b2 8e 2e c8 40 08 05:54:52.649 READ FPDMA QUEUED 60 03 b0 00 98 00 00 b2 8e 2b 18 40 08 05:54:52.646 READ FPDMA QUEUED 60 01 90 00 90 00 00 b2 8e 29 88 40 08 05:54:52.643 READ FPDMA QUEUED 60 02 a8 00 88 00 00 b2 8e 26 e0 40 08 05:54:52.639 READ FPDMA QUEUED Error 4389 [20] occurred at disk power-on lifetime: 39207 hours (1633 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 92 08 20 40 00 Error: UNC at LBA = 0x07920820 = 127010848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 40 00 e0 00 00 07 92 1e 50 40 08 00:34:01.794 READ FPDMA QUEUED 60 05 40 00 d8 00 00 07 92 19 10 40 08 00:34:01.790 READ FPDMA QUEUED 60 05 40 00 d0 00 00 07 92 13 d0 40 08 00:34:01.786 READ FPDMA QUEUED 60 00 20 00 c8 00 00 07 92 13 b0 40 08 00:34:01.727 READ FPDMA QUEUED 60 05 40 00 c0 00 00 07 92 0e 70 40 08 00:34:01.727 READ FPDMA QUEUED Error 4388 [19] occurred at disk power-on lifetime: 39021 hours (1625 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b2 8e 26 98 40 00 Error: UNC at LBA = 0xb28e2698 = 2995660440 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 03 f8 00 d0 00 00 b2 8e 3b 98 40 08 05:41:04.752 READ FPDMA QUEUED 60 01 48 00 c8 00 00 b2 8e 3a 50 40 08 05:41:04.750 READ FPDMA QUEUED 61 03 f8 00 80 00 00 b2 8e 1b 98 40 08 05:41:04.750 WRITE FPDMA QUEUED 60 05 40 00 c0 00 00 b2 8e 1f 90 40 08 05:41:04.750 READ FPDMA QUEUED 60 05 40 00 b8 00 00 b2 8e 24 d0 40 08 05:41:04.750 READ FPDMA QUEUED Error 4387 [18] occurred at disk power-on lifetime: 39021 hours (1625 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b2 8e 1b 98 40 00 Error: UNC at LBA = 0xb28e1b98 = 2995657624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 c0 00 60 00 00 b2 8e 37 08 40 08 05:41:01.147 READ FPDMA QUEUED 60 01 50 00 58 00 00 b2 8e 35 b8 40 08 05:41:01.146 READ FPDMA QUEUED 60 01 38 00 50 00 00 b2 8e 34 80 40 08 05:41:01.144 READ FPDMA QUEUED 60 05 40 00 48 00 00 b2 8e 2f 40 40 08 05:41:01.143 READ FPDMA QUEUED 60 05 30 00 40 00 00 b2 8e 2a 10 40 08 05:41:01.142 READ FPDMA QUEUED Error 4386 [17] occurred at disk power-on lifetime: 39016 hours (1625 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 92 08 20 40 00 Error: UNC at LBA = 0x07920820 = 127010848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 50 00 00 07 92 19 f0 40 08 00:14:55.509 READ FPDMA QUEUED 60 05 40 00 48 00 00 07 92 14 b0 40 08 00:14:55.509 READ FPDMA QUEUED 60 05 40 00 40 00 00 07 92 0f 70 40 08 00:14:55.509 READ FPDMA QUEUED 60 05 40 00 38 00 00 07 92 0a 30 40 08 00:14:55.509 READ FPDMA QUEUED 60 01 70 00 30 00 00 07 92 08 c0 40 08 00:14:55.508 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 10% 39378 2995657632 # 2 Short offline Completed without error 00% 39372 - # 3 Short offline Completed without error 00% 39371 - # 4 Extended offline Aborted by host 90% 39371 - # 5 Extended offline Aborted by host 90% 39348 - # 6 Short offline Completed without error 00% 35662 - # 7 Short offline Completed without error 00% 32260 - # 8 Short offline Completed without error 00% 27319 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 31/40 Celsius Lifetime Min/Max Temperature: 2/56 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (322) Index Estimated Time Temperature Celsius 323 2020-02-16 01:01 38 ******************* ... ..(143 skipped). .. ******************* 467 2020-02-16 03:25 38 ******************* 468 2020-02-16 03:26 37 ****************** ... ..( 29 skipped). .. ****************** 20 2020-02-16 03:56 37 ****************** 21 2020-02-16 03:57 36 ***************** ... ..( 64 skipped). .. ***************** 86 2020-02-16 05:02 36 ***************** 87 2020-02-16 05:03 35 **************** ... ..( 2 skipped). .. **************** 90 2020-02-16 05:06 35 **************** 91 2020-02-16 05:07 34 *************** ... ..( 4 skipped). .. *************** 96 2020-02-16 05:12 34 *************** 97 2020-02-16 05:13 33 ************** ... ..( 6 skipped). .. ************** 104 2020-02-16 05:20 33 ************** 105 2020-02-16 05:21 32 ************* ... ..( 48 skipped). .. ************* 154 2020-02-16 06:10 32 ************* 155 2020-02-16 06:11 31 ************ ... ..( 52 skipped). .. ************ 208 2020-02-16 07:04 31 ************ 209 2020-02-16 07:05 ? - 210 2020-02-16 07:06 31 ************ 211 2020-02-16 07:07 40 ********************* ... ..( 38 skipped). .. ********************* 250 2020-02-16 07:46 40 ********************* 251 2020-02-16 07:47 39 ******************** ... ..( 19 skipped). .. ******************** 271 2020-02-16 08:07 39 ******************** 272 2020-02-16 08:08 38 ******************* ... ..( 49 skipped). .. ******************* 322 2020-02-16 08:58 38 ******************* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 38573 Vendor specific Quote Link to comment
JorgeB Posted February 16, 2020 Share Posted February 16, 2020 1 hour ago, CHINCB said: Based on the Raw_Read_Error_Rate is this dive destined for the recyciling bin? Yes, that and it failed the SMART test. Quote Link to comment
CHINCB Posted February 17, 2020 Author Share Posted February 17, 2020 Thank you Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.