DoboY Posted April 5, 2020 Share Posted April 5, 2020 (edited) ******UPDATE***** Problem solved by moving the 8TB disk to the Marvell controller, great stable connection and no need for new power supply. Decent parity rebuild times also @ ~180M Thanks for the input and help guys.B/s. *************************** I am trying to extend my unraid array by adding a few new 8TB drives, they are shucked WD My books (Model family:WDC HGST Ultrastar He10, Device model:WDC WD80EZAZ-11TDBA0) Partity rebuild fails on either one I try to use about 1.5% into the rebuild. Read errors it seems? maxes out the read error's in the GUI. I have attached the syslog file, hoping someone can point me in the right direction, currently trying to rebuild parity with my original 4TB HGST drive.(hoping that it goes through) Unraid V6.8.3 Gigabyte F2A85XM-HD3 AMD A10-5800K 8GB Ram IOCrest SI-PEX40064(Marvell 88SE9215) <-- only 1 SSD connected to it 500W PSU Total of 7 Sata Hard drives and 2 SSD. diagnostics-20200405-1344.zip Edited April 11, 2020 by DoboY Update Quote Link to comment
JorgeB Posted April 6, 2020 Share Posted April 6, 2020 Loos more like a controller/connection issue, if you haven't yet replace both cables (power + SATA), if still the same and although Marvell controllers are not recommended try connecting the new disk there, to see if it's the same thing Quote Link to comment
DoboY Posted April 6, 2020 Author Share Posted April 6, 2020 (edited) 6 hours ago, johnnie.black said: Loos more like a controller/connection issue, if you haven't yet replace both cables (power + SATA), if still the same and although Marvell controllers are not recommended try connecting the new disk there, to see if it's the same thing I have replaced cables, going to try a new power supply in a few days but not sure that will make a difference as they power up just fine. Any other ideas why they would just go wonky like that after a couple hundred GB written in parity? and both around the same time. I will try and connect them to the Marvell see if it makes a difference . Until then i have started a pre-clear on it and funny thin is it has been running fine on the pre-read stage, 1.5hrs, 8% done.. was crashing at 15 mins when trying to add it as parity drive. still had quite a bit of "hard resetting link" in the logs for that drive for the first hour, but none in the past hour, maybe a power issue? when the system is under heavy load i got power fluctuation issues? The other drive that is just sitting there doing nothing also has same issues, its connected but not added to the array or anything else, Soft resets then sometimes negotiates at 6Gbps, others 3.0 or 1.5... they are plugged in the built in sata on the mobo, where i had the ssd's before. there is a total of 8 onboard sata.. maybe the extra load of having them all populated now is an issue? but i do not get any errors at all on the 6 other sata ports where my 4TB and 1 ssd are plugged in.. no resets. only on these new 8TB WD drives. I will prob try and connect them to the PCI sata card i got but i only got a 1X since i was only going to use it for 1 SSD.. won't have enough bandwidth to support 2 Harddrives at PCIEv2. Apr 6 08:18:45 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:18:46 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:18:46 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:18:46 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:18:47 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:18:57 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 300) Apr 6 08:18:58 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 300) Apr 6 08:19:09 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:19:10 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:19:10 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:19:10 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:19:10 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:19:21 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 300) Apr 6 08:19:21 PinkyPie kernel: ata8: illegal qc_active transition (00000000->00000001) Apr 6 08:19:31 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:19:32 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:19:32 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:19:32 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:19:33 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:20:46 PinkyPie kernel: ata8: limiting SATA link speed to 3.0 Gbps Apr 6 08:20:56 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:20:57 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 08:20:58 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 08:21:08 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:21:10 PinkyPie kernel: ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 320) Apr 6 08:21:10 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:21:10 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:21:10 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:22:04 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:22:05 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 08:22:15 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:22:16 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 08:22:20 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 08:22:20 PinkyPie kernel: ata8.00: disabled Apr 6 08:22:20 PinkyPie kernel: ata8.00: detaching (SCSI 8:0:0:0) Apr 6 08:22:30 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:22:31 PinkyPie kernel: ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 6 08:22:32 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:22:32 PinkyPie kernel: ata8.00: ATA-9: WDC WD80EZAZ-11TDBA0, 1EJAZZPZ, 83.H0A83, max UDMA/133 Apr 6 08:22:32 PinkyPie kernel: ata8.00: 15628053168 sectors, multi 0: LBA48 NCQ (depth 32), AA Apr 6 08:22:33 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:22:33 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:22:33 PinkyPie kernel: sd 8:0:0:0: [sdi] 15628053168 512-byte logical blocks: (8.00 TB/7.28 TiB) Apr 6 08:22:33 PinkyPie kernel: sd 8:0:0:0: [sdi] 4096-byte physical blocks Apr 6 08:22:33 PinkyPie kernel: sd 8:0:0:0: [sdi] Write Protect is off Apr 6 08:22:33 PinkyPie kernel: sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00 Apr 6 08:22:33 PinkyPie kernel: sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Apr 6 08:22:33 PinkyPie kernel: sdi: sdi1 Apr 6 08:22:33 PinkyPie kernel: sd 8:0:0:0: [sdi] Attached SCSI disk Apr 6 08:26:20 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:26:22 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:26:22 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:26:22 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:26:22 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:26:25 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 300) Apr 6 08:26:35 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:26:36 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:26:36 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:26:36 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:26:36 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:26:39 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 300) Apr 6 08:26:49 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:26:50 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:26:50 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:26:51 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:26:52 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:53:12 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:53:13 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:53:13 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:53:13 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:53:13 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:53:31 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 300) Apr 6 08:53:41 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:53:42 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:53:42 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:53:42 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:53:42 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:55:31 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:55:32 PinkyPie kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300) Apr 6 08:55:32 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:55:34 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:55:34 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:56:02 PinkyPie kernel: ata8: limiting SATA link speed to 3.0 Gbps Apr 6 08:56:12 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:56:14 PinkyPie kernel: ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 320) Apr 6 08:56:14 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:56:14 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:56:14 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:57:41 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:57:43 PinkyPie kernel: ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 320) Apr 6 08:57:43 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:57:44 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:57:45 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:57:50 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 08:57:52 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 08:58:02 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 08:58:04 PinkyPie kernel: ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 320) Apr 6 08:58:04 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:58:04 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 08:58:04 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 08:59:54 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 320) Apr 6 09:00:04 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 09:00:06 PinkyPie kernel: ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 320) Apr 6 09:00:06 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:00:06 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:00:06 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 09:00:08 PinkyPie kernel: ata8: limiting SATA link speed to 1.5 Gbps Apr 6 09:00:18 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 09:00:19 PinkyPie kernel: ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:00:20 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:00:20 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:00:21 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 09:01:10 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 09:01:11 PinkyPie kernel: ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:01:11 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:01:11 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:01:12 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 09:01:39 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 09:01:40 PinkyPie kernel: ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:01:40 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:01:40 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:01:40 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 09:03:13 PinkyPie kernel: ata8: SATA link down (SStatus 0 SControl 310) Apr 6 09:03:23 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 09:03:24 PinkyPie kernel: ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:03:24 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:03:26 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:03:26 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 09:23:07 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 09:23:08 PinkyPie kernel: ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:23:08 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:23:08 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:23:08 PinkyPie kernel: ata8.00: configured for UDMA/133 Apr 6 09:23:19 PinkyPie kernel: ata8: softreset failed (device not ready) Apr 6 09:23:20 PinkyPie kernel: ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:23:20 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:23:22 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:23:22 PinkyPie kernel: ata8.00: failed to enable AA (error_mask=0x100) Apr 6 09:23:22 PinkyPie kernel: ata8.00: revalidation failed (errno=-5) Apr 6 09:23:33 PinkyPie kernel: ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:23:33 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:23:35 PinkyPie kernel: ata8.00: supports DRM functions and may not be fully accessible Apr 6 09:23:35 PinkyPie kernel: ata8.00: configured for UDMA/133 Edited April 6, 2020 by DoboY Quote Link to comment
DoboY Posted April 6, 2020 Author Share Posted April 6, 2020 Any ideas why the drives would stop throwing errors about 1 hour into the test? there have been 0 drive errors since about an hour in? nothing has changed on the array, load has be low and high at times and still no more errors? have not touched a thing. Apr 6 09:00:44 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 708460368 Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#2 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#2 Sense Key : 0x5 [current] Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#2 ASC=0x21 ASCQ=0x4 Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#2 CDB: opcode=0x88 88 00 00 00 00 00 2a 3a 44 00 00 00 05 40 00 00 Apr 6 09:00:44 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 708461568 Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 Sense Key : 0x5 [current] Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 ASC=0x21 ASCQ=0x4 Apr 6 09:00:44 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 CDB: opcode=0x88 88 00 00 00 00 00 2a 3a 49 40 00 00 00 c0 00 00 Apr 6 09:00:44 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 708462912 Apr 6 09:00:44 PinkyPie kernel: ata7: EH complete Apr 6 09:00:44 PinkyPie kernel: ata7.00: exception Emask 0x10 SAct 0x1800018 SErr 0x10200 action 0xe frozen Apr 6 09:00:44 PinkyPie kernel: ata7.00: irq_stat 0x00400000, PHY RDY changed Apr 6 09:00:44 PinkyPie kernel: ata7: SError: { Persist PHYRdyChg } Apr 6 09:00:44 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:00:44 PinkyPie kernel: ata7.00: cmd 60/a8:18:00:ba:3a/05:00:2a:00:00/40 tag 3 ncq dma 741376 in Apr 6 09:00:44 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:00:44 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:00:44 PinkyPie kernel: ata7.00: cmd 60/58:20:a8:bf:3a/04:00:2a:00:00/40 tag 4 ncq dma 569344 in Apr 6 09:00:44 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:00:44 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:00:44 PinkyPie kernel: ata7.00: cmd 60/40:b8:00:c4:3a/05:00:2a:00:00/40 tag 23 ncq dma 688128 in Apr 6 09:00:44 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:00:44 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:00:44 PinkyPie kernel: ata7.00: cmd 60/c0:c0:40:c9:3a/00:00:2a:00:00/40 tag 24 ncq dma 98304 in Apr 6 09:00:44 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:00:44 PinkyPie kernel: ata7: hard resetting link Apr 6 09:00:54 PinkyPie kernel: ata7: softreset failed (device not ready) Apr 6 09:00:54 PinkyPie kernel: ata7: hard resetting link Apr 6 09:00:56 PinkyPie kernel: ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:00:56 PinkyPie kernel: ata7.00: supports DRM functions and may not be fully accessible Apr 6 09:00:56 PinkyPie kernel: ata7.00: supports DRM functions and may not be fully accessible Apr 6 09:00:57 PinkyPie kernel: ata7.00: configured for UDMA/33 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 Sense Key : 0x5 [current] Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 ASC=0x21 ASCQ=0x4 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#3 CDB: opcode=0x88 88 00 00 00 00 00 2a 3a ba 00 00 00 05 a8 00 00 Apr 6 09:00:57 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 708491776 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#4 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#4 Sense Key : 0x5 [current] Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#4 ASC=0x21 ASCQ=0x4 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#4 CDB: opcode=0x88 88 00 00 00 00 00 2a 3a bf a8 00 00 04 58 00 00 Apr 6 09:00:57 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 708493224 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#23 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#23 Sense Key : 0x5 [current] Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#23 ASC=0x21 ASCQ=0x4 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#23 CDB: opcode=0x88 88 00 00 00 00 00 2a 3a c4 00 00 00 05 40 00 00 Apr 6 09:00:57 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 708494336 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#24 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#24 Sense Key : 0x5 [current] Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#24 ASC=0x21 ASCQ=0x4 Apr 6 09:00:57 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#24 CDB: opcode=0x88 88 00 00 00 00 00 2a 3a c9 40 00 00 00 c0 00 00 Apr 6 09:00:57 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 708495680 Apr 6 09:00:57 PinkyPie kernel: ata7: EH complete Apr 6 09:23:10 PinkyPie kernel: ata7.00: exception Emask 0x10 SAct 0x46088000 SErr 0x10200 action 0xe frozen Apr 6 09:23:10 PinkyPie kernel: ata7.00: irq_stat 0x00400000, PHY RDY changed Apr 6 09:23:10 PinkyPie kernel: ata7: SError: { Persist PHYRdyChg } Apr 6 09:23:10 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:23:10 PinkyPie kernel: ata7.00: cmd 60/01:78:82:f9:b6/00:00:7c:00:00/40 tag 15 ncq dma 512 in Apr 6 09:23:10 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:23:10 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:23:10 PinkyPie kernel: ata7.00: cmd 60/01:98:94:f3:0a/00:00:c2:00:00/40 tag 19 ncq dma 512 in Apr 6 09:23:10 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:23:10 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:23:10 PinkyPie kernel: ata7.00: cmd 60/70:c8:00:ca:df/05:00:3f:00:00/40 tag 25 ncq dma 712704 in Apr 6 09:23:10 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:23:10 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:23:10 PinkyPie kernel: ata7.00: cmd 60/90:d0:70:cf:df/04:00:3f:00:00/40 tag 26 ncq dma 598016 in Apr 6 09:23:10 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:23:10 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:23:10 PinkyPie kernel: ata7.00: cmd 60/01:f0:69:7b:82/00:00:0c:00:00/40 tag 30 ncq dma 512 in Apr 6 09:23:10 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:23:10 PinkyPie kernel: ata7: hard resetting link Apr 6 09:23:20 PinkyPie kernel: ata7: softreset failed (device not ready) Apr 6 09:23:20 PinkyPie kernel: ata7: hard resetting link Apr 6 09:23:22 PinkyPie kernel: ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:23:22 PinkyPie kernel: ata7.00: supports DRM functions and may not be fully accessible Apr 6 09:23:22 PinkyPie kernel: ata7.00: supports DRM functions and may not be fully accessible Apr 6 09:23:22 PinkyPie kernel: ata7.00: configured for UDMA/33 Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#25 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#25 Sense Key : 0x5 [current] Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#25 ASC=0x21 ASCQ=0x4 Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#25 CDB: opcode=0x88 88 00 00 00 00 00 3f df ca 00 00 00 05 70 00 00 Apr 6 09:23:22 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 1071630848 Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#26 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#26 Sense Key : 0x5 [current] Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#26 ASC=0x21 ASCQ=0x4 Apr 6 09:23:22 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#26 CDB: opcode=0x88 88 00 00 00 00 00 3f df cf 70 00 00 04 90 00 00 Apr 6 09:23:22 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 1071632240 Apr 6 09:23:22 PinkyPie kernel: ata7: EH complete Apr 6 09:23:25 PinkyPie kernel: ata7.00: exception Emask 0x10 SAct 0xc00 SErr 0x40d0202 action 0xe frozen Apr 6 09:23:25 PinkyPie kernel: ata7.00: irq_stat 0x00400000, PHY RDY changed Apr 6 09:23:25 PinkyPie kernel: ata7: SError: { RecovComm Persist PHYRdyChg CommWake 10B8B DevExch } Apr 6 09:23:25 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:23:25 PinkyPie kernel: ata7.00: cmd 60/c0:50:00:fa:e3/05:00:3f:00:00/40 tag 10 ncq dma 753664 in Apr 6 09:23:25 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:23:25 PinkyPie kernel: ata7.00: failed command: READ FPDMA QUEUED Apr 6 09:23:25 PinkyPie kernel: ata7.00: cmd 60/40:58:c0:ff:e3/04:00:3f:00:00/40 tag 11 ncq dma 557056 in Apr 6 09:23:25 PinkyPie kernel: ata7.00: status: { DRDY } Apr 6 09:23:25 PinkyPie kernel: ata7: hard resetting link Apr 6 09:23:35 PinkyPie kernel: ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Apr 6 09:23:35 PinkyPie kernel: ata7.00: supports DRM functions and may not be fully accessible Apr 6 09:23:36 PinkyPie kernel: ata7.00: supports DRM functions and may not be fully accessible Apr 6 09:23:37 PinkyPie kernel: ata7.00: configured for UDMA/33 Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#10 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#10 Sense Key : 0x5 [current] Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#10 ASC=0x21 ASCQ=0x4 Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#10 CDB: opcode=0x88 88 00 00 00 00 00 3f e3 fa 00 00 00 05 c0 00 00 Apr 6 09:23:37 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 1071905280 Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#11 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#11 Sense Key : 0x5 [current] Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#11 ASC=0x21 ASCQ=0x4 Apr 6 09:23:37 PinkyPie kernel: sd 7:0:0:0: [sdh] tag#11 CDB: opcode=0x88 88 00 00 00 00 00 3f e3 ff c0 00 00 04 40 00 00 Apr 6 09:23:37 PinkyPie kernel: print_req_error: I/O error, dev sdh, sector 1071906752 Apr 6 09:23:37 PinkyPie kernel: ata7: EH complete Quote Link to comment
Vr2Io Posted April 6, 2020 Share Posted April 6, 2020 Suggest you try rebuild in safe mode. Quote Link to comment
DoboY Posted April 6, 2020 Author Share Posted April 6, 2020 5 minutes ago, Benson said: Suggest you try rebuild in safe mode. Thanks for taking the time. How does that differ from normal if i may ask? what kind of functionality would i lose during the rebuild, i restarted the pre clear and since they have both connected at 1.5Gbps they seem to be working normally, is there a way to limit the connection speed somehow(hard code)? The logs had some errors before of "limiting SATA link speed to 3.0 Gbps, then more errors then limiting SATA link speed to 1.5 Gbps.. then no more errors?. Quote Link to comment
Vr2Io Posted April 6, 2020 Share Posted April 6, 2020 (edited) 12 minutes ago, DoboY said: Thanks for taking the time. How does that differ from normal if i may ask? what kind of functionality would i lose during the rebuild, i restarted the pre clear and since they have both connected at 1.5Gbps they seem to be working normally, is there a way to limit the connection speed somehow(hard code)? The logs had some errors before of "limiting SATA link speed to 3.0 Gbps, then more errors then limiting SATA link speed to 1.5 Gbps.. then no more errors?. Seems only old model support setting to 1.5Gbps by jumper, btw, I don't think those was a correct direction. Longtime ago, I need set my WD drive to 1.5Gbps when it connect thr a USB-SATA bridge to avoid the bridge reset itself. ( those are 2TB disk and problem not on disk ) Edited April 6, 2020 by Benson Quote Link to comment
DoboY Posted April 6, 2020 Author Share Posted April 6, 2020 1 minute ago, Benson said: Seems only old model support setting to 1.5Gbps by jumper, btw, I don't think those was a correct direction. Longtime ago, I need set my WD drive to 1.5Gbps when it connect thr a USB-SATA bridge to avoide the bridge reset itself. that could be my issue ( USB-SATA bridge) but I cannot find any info about the mobo and what type of SATA controller it has. it is an old motherboard (2012) Quote Link to comment
Vr2Io Posted April 6, 2020 Share Posted April 6, 2020 (edited) 7 minutes ago, DoboY said: that could be my issue ( USB-SATA bridge) but I cannot find any info about the mobo and what type of SATA controller it has. it is an old motherboard (2012) Newer WD disk shouldn't have this feature, pls forget it. And my case just for that bridge, I got another bridge later and no problem again. Your MB chipset was A85, 8 port SATA chipset. Edited April 6, 2020 by Benson Quote Link to comment
DoboY Posted April 6, 2020 Author Share Posted April 6, 2020 1 minute ago, Benson said: Newer WD disk shouldn't have this feature, pls forget it. And my case just for that bridge, I got another bridge later and no problem again. Ok well then I am back to having zero idea why they seem to run fine atm @ 1.5Gbps, as soon as i reboot or stop start the array i am sure they will renegotiate and get screwy on me again, i have a new power supply coming in tomorrow so I will re-wire it all and try again, if it still gives me issues will try the Marvell Sata card i have to see if it handles it better.. just seems odd is all. currently zeroing out both drives @ 130+MBps and no errors yet. So strange.. Quote Link to comment
Vr2Io Posted April 6, 2020 Share Posted April 6, 2020 (edited) 4 minutes ago, DoboY said: Ok well then I am back to having zero idea why they seem to run fine atm @ 1.5Gbps, as soon as i reboot or stop start the array i am sure they will renegotiate and get screwy on me again, i have a new power supply coming in tomorrow so I will re-wire it all and try again, if it still gives me issues will try the Marvell Sata card i have to see if it handles it better.. just seems odd is all. currently zeroing out both drives @ 130+MBps and no errors yet. So strange.. So like @johnnie.black reply, I vote its controller side problem, just try to found a way to bypass the problem. Agree, problem so strange. Edited April 6, 2020 by Benson Quote Link to comment
DoboY Posted April 7, 2020 Author Share Posted April 7, 2020 And pre-clear passed on both drives.. no more error's in the logs, but only after they both dropped down to SATA 1.5Gbps.. So weird. swapping Power supply today and trying parity again I guess.. Quote Link to comment
Vr2Io Posted April 7, 2020 Share Posted April 7, 2020 If any PHY reset and link drop to 1.5Gbps, that means problem persists and you should stop rebuild or preclear, keep try other solution. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.