Temp Monitor Errors - Ryzen+X570 (ASUS TUF)


30 posts in this topic Last Reply

Recommended Posts

Hi all,

I've been trying for a while to get temp monitor working with My Ryzen setup.

Trying to get the temps working for my ASUS TUF GAMING X570-PLUS (WI-FI), without much luck.

Recently with the 6.9.0-beta1 release, I understand that there is support in the new kernel.

 

When I initially upgraded from 6.8.3 to 6.9.0-beta1, I noticed that some temps were visible, but they have gone and now I get an error in my log when I "Load Drivers".

 

I've seen in the 6.9.0-beta1 release thread that I should add `acpi_enforce_resources=lax` to my flash syslinux config, which I did:

image.png.c22c383801b9d5d8f048542abb1b39dc.png

(I also loaded perl from Nerd pack without issue or error).

 

Log during detection process:

May 6 11:11:40 blaster kernel: i2c /dev entries driver
May 6 11:11:51 blaster kernel: nct6775: Found NCT6798D or compatible chip at 0x2e:0x290
May 6 11:11:51 blaster kernel: ACPI Warning: SystemIO range 0x0000000000000295-0x0000000000000296 conflicts with OpRegion 0x0000000000000290-0x0000000000000299 (\AMW0.SHWM) (20191018/utaddress-204)
May 6 11:11:51 blaster kernel: ACPI: This conflict may cause random problems and system instability
May 6 11:11:51 blaster kernel: ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
May 6 11:11:51 blaster kernel: nct6775 nct6775.656: Invalid temperature source 28 at index 0, source register 0x100, temp register 0x73
May 6 11:11:51 blaster kernel: nct6775 nct6775.656: Invalid temperature source 28 at index 1, source register 0x200, temp register 0x75
May 6 11:11:51 blaster kernel: nct6775 nct6775.656: Invalid temperature source 28 at index 2, source register 0x300, temp register 0x77
May 6 11:11:51 blaster kernel: nct6775 nct6775.656: Invalid temperature source 28 at index 3, source register 0x800, temp register 0x79
May 6 11:11:51 blaster kernel: nct6775 nct6775.656: Invalid temperature source 28 at index 5, source register 0xa00, temp register 0x7d

 

I can detect a few different drivers/devices:

image.png.c6c4e5c461a9c8712a7c9fb8bf0056ba.png

 

Error when I "Load Drivers":

ACPI Warning: SystemIO range 0x0000000000000295-0x0000000000000296 conflicts with OpRegion 0x0000000000000290-0x0000000000000299 (\AMW0.SHWM) (20191018/utaddress-204)

 

And now all the "Sensors" below are always blank no matter what:

image.png.242cb166bf2c1cd6121960130d1755d5.png

 

Any ideas what might be the matter?

Link to post

Still trying, the result of my `sensors-detect`

root@blaster:~# sensors-detect
# sensors-detect version 3.6.0
# Board: ASUSTeK COMPUTER INC. TUF GAMING X570-PLUS (WI-FI)
# Kernel: 5.5.8-Unraid x86_64
# Processor: AMD Ryzen 5 3600 6-Core Processor (23/113/0)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): YES
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 16h thermal sensors...                           No
AMD Family 17h thermal sensors...                           Success!
    (driver `k10temp')
AMD Family 15h power sensors...                             No
AMD Family 16h power sensors...                             No
Hygon Family 18h thermal sensors...                         No
Intel digital thermal sensor...                             No
Intel AMB FB-DIMM thermal sensor...                         No
Intel 5500/5520/X58 thermal sensor...                       No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               Yes
Found `Nuvoton NCT6798D Super IO Sensors'                   Success!
    (address 0x290, driver `nct6775')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): YES
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): YES
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): YES
Using driver `i2c-piix4' for device 0000:00:14.0: AMD KERNCZ SMBus
Module i2c-dev loaded successfully.

Next adapter: SMBus PIIX4 adapter port 0 at 0b00 (i2c-0)
Do you want to scan it? (YES/no/selectively): YES
Client found at address 0x1a
Probing for `Analog Devices ADM1021'...                     No
Probing for `Analog Devices ADM1021A/ADM1023'...            No
Probing for `Maxim MAX1617'...                              No
Probing for `Maxim MAX1617A'...                             No
Probing for `Maxim MAX1668'...                              No
Probing for `Maxim MAX1805'...                              No
Probing for `Maxim MAX1989'...                              No
Probing for `Maxim MAX6655/MAX6656'...                      No
Probing for `TI THMC10'...                                  No
Probing for `National Semiconductor LM84'...                No
Probing for `Genesys Logic GL523SM'...                      No
Probing for `Onsemi MC1066'...                              No
Probing for `Maxim MAX1618'...                              No
Probing for `Maxim MAX1619'...                              No
Probing for `National Semiconductor LM82/LM83'...           No
Probing for `Maxim MAX6654'...                              No
Probing for `Maxim MAX6690'...                              No
Probing for `Maxim MAX6680/MAX6681'...                      No
Probing for `Maxim MAX6695/MAX6696'...                      No
Probing for `Texas Instruments TMP400'...                   No
Probing for `Texas Instruments AMC6821'...                  No
Probing for `ST STTS424'...                                 No
Probing for `ST STTS424E'...                                No
Probing for `ST STTS2002'...                                No
Probing for `ST STTS3000'...                                No
Probing for `NXP SE97/SE97B'...                             No
Probing for `NXP SE98'...                                   No
Probing for `Analog Devices ADT7408'...                     No
Probing for `IDT TS3000/TSE2002'...                         No
Probing for `IDT TSE2004'...                                No
Probing for `IDT TS3001'...                                 No
Probing for `Maxim MAX6604'...                              No
Probing for `Microchip MCP9804'...                          No
Probing for `Microchip MCP9808'...                          No
Probing for `Microchip MCP98242'...                         No
Probing for `Microchip MCP98243'...                         No
Probing for `Microchip MCP98244'...                         Success!
    (confidence 5, driver `jc42')
Probing for `Microchip MCP9843'...                          No
Probing for `ON CAT6095/CAT34TS02'...                       No
Probing for `ON CAT34TS02C'...                              No
Probing for `ON CAT34TS04'...                               No
Probing for `Atmel AT30TS00'...                             No
Probing for `Giantec GT30TS00'...                           No
Client found at address 0x1b
Probing for `ST STTS424'...                                 No
Probing for `ST STTS424E'...                                No
Probing for `ST STTS2002'...                                No
Probing for `ST STTS3000'...                                No
Probing for `NXP SE97/SE97B'...                             No
Probing for `NXP SE98'...                                   No
Probing for `Analog Devices ADT7408'...                     No
Probing for `IDT TS3000/TSE2002'...                         No
Probing for `IDT TSE2004'...                                No
Probing for `IDT TS3001'...                                 No
Probing for `Maxim MAX6604'...                              No
Probing for `Microchip MCP9804'...                          No
Probing for `Microchip MCP9808'...                          No
Probing for `Microchip MCP98242'...                         No
Probing for `Microchip MCP98243'...                         No
Probing for `Microchip MCP98244'...                         Success!
    (confidence 5, driver `jc42')
Probing for `Microchip MCP9843'...                          No
Probing for `ON CAT6095/CAT34TS02'...                       No
Probing for `ON CAT34TS02C'...                              No
Probing for `ON CAT34TS04'...                               No
Probing for `Atmel AT30TS00'...                             No
Probing for `Giantec GT30TS00'...                           No
Client found at address 0x52
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Client found at address 0x53
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)

Next adapter: SMBus PIIX4 adapter port 2 at 0b00 (i2c-1)
Do you want to scan it? (YES/no/selectively): YES


Now follows a summary of the probes I have just done.
Just press ENTER to continue: 

Driver `k10temp':
  * Chip `AMD Family 17h thermal sensors' (confidence: 9)

Driver `jc42':
  * Bus `SMBus PIIX4 adapter port 0 at 0b00'
    Busdriver `i2c_piix4', I2C address 0x1a
    Chip `Microchip MCP98244' (confidence: 5)
  * Bus `SMBus PIIX4 adapter port 0 at 0b00'
    Busdriver `i2c_piix4', I2C address 0x1b
    Chip `Microchip MCP98244' (confidence: 5)

Driver `nct6775':
  * ISA bus, address 0x290
    Chip `Nuvoton NCT6798D Super IO Sensors' (confidence: 9)

Do you want to generate /etc/sysconfig/lm_sensors? (yes/NO): yes
Copy prog/init/lm_sensors.init to /etc/init.d/lm_sensors
for initialization at boot time.
You should now start the lm_sensors service to load the required
kernel modules.

Unloading i2c-dev... OK

 

Link to post
  • 5 months later...

@KptnKMan May I ask you for a quick review of that board?

Did you ran into any problems? (beside this here with the temp monitor)

Or do you got useful tips/hints for better bios settings or an unproblematic unRAID installation?

 

I'm planing to send my i7 6700 in his well earned retirement and the ASUS TUF GAMING X570-PLUS is one of my two options. 

I don't need the WiFi model but as far as I researched all other specs are totally identical. 

 

Thank you for any information. 

Link to post
  • 2 weeks later...

Hey @Maddeen I wrote a response to you but apparently it seemed to have not posted a week ago.

 

The ASUS TUF GAMING X570-PLUS (WI-FI) is a great board for my Unraid.

I've had no issues with it, apart from the thermal sensor issue in this thread.

I currently run 64GB (2x 32GB) of Micron Multi-Bit ECC DDR4 at 3200MHz and it works great. I'm considering doubling that.

The reason I got this board is because I wanted a board that was:

- rock-solid stable

- X570 chipset

- 2x NVME M.2 x4 PCIe Gen 4 slots

- ECC support (unofficial, but ASUS is good with including ECC support)

- 8x onboard SATA

- 2x PCIe x16 slots

 

It delivered on all those accounts.

I don't use the onboard WiFi but I wanted to possibly make a VM as a AP, and host that in Unraid.

 

Also, it would seem that I got the thermal sensor to finally work on the 2407 BIOS, no idea what changed.

So even that niggle seems to be working now.

Link to post

@KptnKMan thank you very much.

I wasn't sure if my first decision for this board is right - but after your review, I'll definitely go with the TUF - but without WiFi, because I dont have a usecase for that 😜

 

I selected the TUF over others because of the following reasons

- X570 Chipset to be able to use latest Ryzen 

- 8x SATA

- No PCI-E lane sharing. 

Last bullet point wasn't as easy as I thought.

I was kind of shocked when I found out that the majority of the boards (even the more expensive) share PCI-E lanes or - even worse - share m.2 with SATA. 

 

Do you use any 10Gb NIC and have a recommendation too?

 

And please - if you need to made any special "moves" to get the thermal sensor running - please write it down here 😝

 

Link to post

Wow thanks for this, i was literally about to get this card but decided to do some research on it first... don't like the look of this but friends of mine have had fine experiences with it - still the risk is enough for me to go down another road...

Edited by mscott
Link to post

@Maddeen I didn't have to do anything special to get the temp monitor to work, but now it is:

image.thumb.png.ae105aae070ded23bb727c50ecc08ff2.png

 

I'm still on the 2407 BIOS, so it might be that version that got things working, but I'll need to update at some point as I intend to upgrade to a Ryzen 5000-series CPU in the coming months.

 

@mscott I have no idea what "card" you're referring to. Can you explain?

Edited by KptnKMan
Link to post

@Maddeen The only gripe I might have with this motherboard is the lack of PCIe slots, but the chipset is PCIe 4.0, so that probably explains the dedicated lanes.

I am waiting for a PCIe4.0 1x 10Gb NIC to come out.

 

Right now I'm using a PCIe 1x Dual 1Gb Intel card, teamed with my onboard, for 3Gb throughput, and that works well.

My backup Unraid also uses the same configuration, and I get a nice 3Gb/s between them.

 

There are PCIe4.0 1x NICs with 4x 1Gb on them, but I'm not too concerned about them right now.

Link to post

@KptnKMan 

Today I received my TUF X570 - now just waiting for my 3700X - ETA tomorrow :)

Do you made an upgrade from an existing unraid server and have any useful tipps/hints for that?

 

Or is it just like it was for majority here; Replace board + cpu - change boot device to usb - and it all just works?! :) 

Link to post

@Maddeen

Oooh, I would have waited just a couple weeks for the Ryzen 5000 chips, in particular the 5600X or 5800X for you.

 

Anyhow, I upgraded from my (Now Backup) unraid to my new Ryzen build earlier this year.

If you have your array setup now without any issues, and you're migrating to the same version, it should be easy to swap your disks out. You'll be able to find plenty of advice on this forum about that, from better people than me. :)

 

You should basically be able to swap your hardware out, as far as I'm aware.

Link to post

I already made one board+cpu change earlier this year. I just asked in relation to the X570 especially. 

So if you don't need to do some special "tricks" to get in run, I'm fine :) 

 

btw - have you found here in the community a guide for the best bios settings? I searched for it but due to the mass of keywords like "bios" in the results I didn't found one ;-)

 

I was pondered if I want to wait but I get a (imho) special offer - I just paying 200€ ($236) for a new X3700. 

For this price I not even get a 5600 - :(

Edited by Maddeen
Link to post
2 hours ago, Maddeen said:

@KptnKMan 

Today I received my TUF X570 - now just waiting for my 3700X - ETA tomorrow :)

Do you made an upgrade from an existing unraid server and have any useful tipps/hints for that?

 

Or is it just like it was for majority here; Replace board + cpu - change boot device to usb - and it all just works?! :) 

From what I understand, yes.

Does not hurt to make a backup of your flash and note your disk assignements, just in case.

Also, if you have VMs, the passthrough elements would have to be checked and potentially changed.

Link to post

@KptnKMan

I finally upgraded successfully :) All up and running. Thank you

But I can only detect two temp sensors --> k10temp nct6775

Your jc42 sensor is not showing up. What is this for a sensor? Did I miss something?

 

And I dont have any of the fan speeds... is this a separate plugin?

Link to post
  • 2 weeks later...
On 10/24/2020 at 12:47 PM, Maddeen said:

@KptnKMan

I finally upgraded successfully :) All up and running. Thank you

But I can only detect two temp sensors --> k10temp nct6775

Your jc42 sensor is not showing up. What is this for a sensor? Did I miss something?

 

And I dont have any of the fan speeds... is this a separate plugin?

Hi. i have the same specs. migrate mobo and cpu. but has problems at the start . Whats is your disk assignment on the Sata ports ?

Initially I started

sata 1 Parity1 4tb

sata 2 parity2 4tb

sata 3 Disk 1 4tb

sata 4 Disk 2 4tb

sata 5 disk 3 4tb

sata 6 disk 4 4tb

sata 7 SSD Cache 256gb

sata 8 SSD unassigned vm storage 128gb

m2. slot 1 nvme 250gb unassigned, for pass to VM

 

1 vga GTX 1060 for pass Win 10 VM

1 vga Radeon 580 for pass OS X VM

1 Sound blaster ZXR for pass win 10VM 

 

With that configuration I have problems with the array and errors on Sata 1 and Sata 6, both disk was disabled after severals read errors.

 

I removed the M2 Slot 1 and everything start working properly, I rebuild data from disk 4 and rebuild parity 1 drive.

 

 

 

I think asus disable 2 Sata ports if you are using a nvme drive but is not mentioned on the manual. I tested 3 weeks ago a x470 mainboard and in the documentation its special section that mentions the Sata ports disabled with the use of the m2 slots.

 

now my only problem remains in the data temp.

Link to post
2 minutes ago, NetMaster said:

With that configuration I have problems with the array and errors on Sata 1 and Sata 6, both disk was disabled after severals read errors.

 

I removed the M2 Slot 1 and everything start working properly, I rebuild data from disk 4 and rebuild parity 1 drive.

 

 

 

I think asus disable 2 Sata ports if you are using a nvme drive but is not mentioned on the manual. I tested 3 weeks ago a x470 mainboard and in the documentation its special section that mentions the Sata ports disabled with the use of the m2 slots.

 

now my only problem remains in the data temp.

This is NOT true, and you should not be telling people to make decisions like this based on your unfounded assumption that it is not in the manual.

You should also NOT be making recommendations based upon assumption of something you saw in another motherboards manual, with a different chipset generation. Please don't do that.

 

I am using all 8 SATA ports and both NVME slots, and all work fine together.

 

If you are using THE EXACT SAME motherboard, it sounds like you have a fault and should probably contact ASUS support.

Link to post
On 10/24/2020 at 5:47 PM, Maddeen said:

@KptnKMan

I finally upgraded successfully :) All up and running. Thank you

But I can only detect two temp sensors --> k10temp nct6775

Your jc42 sensor is not showing up. What is this for a sensor? Did I miss something?

 

And I dont have any of the fan speeds... is this a separate plugin?

Everything is working fine for me, and I also only have the same 2 monitors now.

image.png.5798f0158c8abe11423890a2be46aba7.png

 

From what I can see, the other "jc42" sensor is not not detected, and I have all the monitors that I need.

So between BIOS updates looks like they fixed it.

Link to post

@KptnKMan - perfect - I was just wondering why you got one sensor more in your screenshot. 

 

@NetMaster - I dont need all ports, but I have 6x SATA Ports  (4x 4TB Iron Wolf 2x 512 SSD Cache pool) and one m2 slot (the one with the heat sink - bare metal win10 installation) in use - no problems. 

And as KptnKMan said - there is no sharing/disabling - neither pci-e sharing nor SATA sharing! 
That's why I (and KptnKMan too - i think) choose that board instead of others which use sharing. 

Edited by Maddeen
Link to post
9 hours ago, KptnKMan said:

This is NOT true, and you should not be telling people to make decisions like this based on your unfounded assumption that it is not in the manual.

You should also NOT be making recommendations based upon assumption of something you saw in another motherboards manual, with a different chipset generation. Please don't do that.

 

I am using all 8 SATA ports and both NVME slots, and all work fine together.

 

If you are using THE EXACT SAME motherboard, it sounds like you have a fault and should probably contact ASUS support.

that is the reason i am asking for help.

8 sata ports are working fine without m2 slots in use.

test lab was 1 slot m2 nvme with 3 sata ports and 1 VGA, was running perfect with no issues.

i read similar complaints in asus forums about this. what bios version are you running ? running bios 2607 for me.

 

i never made a recommendations  about anything. just posted what  i've experienced in my tests.

i read also about max pci-e lane are not enough and  shared bandwidth is enabled if you try to run all slots at max speed.  any readings recommendations with those specs and architecture specifications ?

 

 

 

 

 

 

Link to post
3 hours ago, Maddeen said:

@KptnKMan - perfect - I was just wondering why you got one sensor more in your screenshot. 

 

@NetMaster - I dont need all ports, but I have 6x SATA Ports  (4x 4TB Iron Wolf 2x 512 SSD Cache pool) and one m2 slot (the one with the heat sink - bare metal win10 installation) in use - no problems. 

And as KptnKMan said - there is no sharing/disabling - neither pci-e sharing nor SATA sharing! 
That's why I (and KptnKMan too - i think) choose that board instead of others which use sharing. 

ok. need to do another test.  maybe is some settings on the bios or another config error.  what do you have to says about the comment below

I've done a bit more research and think this may have to do with not having enough PCIe Lanes.

I'm using a Ryzen 7 3700x = 24 PCIe Lanes

Chipset - 4 lanes
1 x nvme SSD - 4 lanes
GPU (2070 super) - 16 lanes

= not enough lanes for the additional nvme SSD?

So maybe I need a 2.5 SSD instead

 

i don't know about lanes assigned. or how are handled by the motherboard.

 

Link to post
1 hour ago, NetMaster said:

that is the reason i am asking for help.

8 sata ports are working fine without m2 slots in use.

test lab was 1 slot m2 nvme with 3 sata ports and 1 VGA, was running perfect with no issues.

i read similar complaints in asus forums about this. what bios version are you running ? running bios 2607 for me.

 

i never made a recommendations  about anything. just posted what  i've experienced in my tests.

i read also about max pci-e lane are not enough and  shared bandwidth is enabled if you try to run all slots at max speed.  any readings recommendations with those specs and architecture specifications ?

 

1 hour ago, NetMaster said:

ok. need to do another test.  maybe is some settings on the bios or another config error.  what do you have to says about the comment below

I've done a bit more research and think this may have to do with not having enough PCIe Lanes.

I'm using a Ryzen 7 3700x = 24 PCIe Lanes

Chipset - 4 lanes
1 x nvme SSD - 4 lanes
GPU (2070 super) - 16 lanes

= not enough lanes for the additional nvme SSD?

So maybe I need a 2.5 SSD instead

 

i don't know about lanes assigned. or how are handled by the motherboard.

I don't mean to be rude, but you need to start a separate thread about these issues.

Thanks.

 

If you want help then start a thread and people can choose to respond there, don't derail another thread.

It's rude to other people trying to discuss and get help for their particular issues.

 

We are discussing the temp monitor addon, getting it working, and which BIOS version it works with on this particular motherboard.

You also STILL have not indicated exactly which motherboard you are in fact using, and nothing is in your signature.

 

Or contact ASUS support, as I advised.

 

Edit: I see you already have a thread discussing your issues. That's great. You need to respond there about this, thanks.

Edited by KptnKMan
Link to post
5 hours ago, Maddeen said:

@KptnKMan - perfect - I was just wondering why you got one sensor more in your screenshot. 

@Maddeen This seemed to be something with the earlier BIOS version I was on.

 

I'm planning to get a Ryzen 5000 chip in the future when they become generally available, so I've been wondering if anything will change again with that upgrade.

 

The newer Ryzen 5000 chips require a BIOS with AGESA 1.0.8.0, but I think they recommend AGESA 1.1.0.0 for full support.

Edited by KptnKMan
Link to post
  • 1 month later...

I'm currently on 2407, but my Ryzen 9 5950x just arrived, so I need to upgrade.

 

I've downloaded the 2802 non-beta and the 2816 beta BIOS, but I'll be using the non-beta for now as it has AGESA 1.1.0.0 needed for Zen 3.

For the record, I think Zen 3 requires at least AGESA 1.0.8.0, in BIOS version 2607+.

 

Gonna do that first and see if temp monitors are still working, before swapping in the new chip.

 

@Kash76 this might be useful for you.

Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.