Jump to content
Sign in to follow this  
bdydrp

[SOLVED] New hardware , No webUI

20 posts in this topic Last Reply

Recommended Posts

Posted (edited)

Ive just replaced my hardware (cpu,mobo,ram) and cannot access my system via webUI

 

Ive attached a monitor and keyboard to my system and can access bios just fine, 

Unraid boots to the splashscreen where i can make a choice.

Unraid OS - Takes me to the following:

image.thumb.png.09f6a11146057f759307ce4c0ba28401.png

I can login at this cmd line

But i cant access the server via IP on another machine

 

Unraid OS with GUI - Takes me to a blank screen with a white - in the top right hand corner. And still no access via another machine

 

Lost on what to try next?

Edited by bdydrp
SOLVED

Share this post


Link to post

It could be that it's using a different NIC or the order changed, you can boot with GUI mode and change witch NIC it eth0

Share this post


Link to post
Posted (edited)

If i select boot with GUI, all i get is blank screen with a dash in the top left corner!

 

Can u put the unraid USB in a PC and change any settings manually??

Edited by bdydrp

Share this post


Link to post

Delete/rename network.cfg and network-rules.cfg both in the config folder, then boot again, you still might need to change the cable to a different NIC depending on witch one gets assigned by default as eth0.

Share this post


Link to post
Posted (edited)

Ive removed both files

Also removed the 4 port intel card so that its forced to use the onboard NIC

 

When unraid loads, i get to login 

The lines

IPv4 - Not set

IPv6 - Not set

 

Should both network.cfg and network-rules.cfg files get re-created upon boot?

And an IP should be assigned via DHCP?

 

Also, selecting Unraid with WebUI, only loads to blank screen still!

 

 

Edited by bdydrp

Share this post


Link to post
2 minutes ago, bdydrp said:

Should both network.cfg and network-rules.cfg files get re-created upon boot?

With a single NIC only network.cfg would be re-created, if it isn't it points to a problem with the flash drive, i.e., it's not booting correctly.

 

3 minutes ago, bdydrp said:

And an IP should be assigned via DHCP?

Yes.

 

Backup current flash, re-create it using the USB tool then restore the config folder.

 

Share this post


Link to post
Posted (edited)

Thanks

 

 

28 minutes ago, johnnie.black said:

With a single NIC only network.cfg would be re-created, if it isn't it points to a problem with the flash drive, i.e., it's not booting correctly.

I'll double check, but i dont think a new network.cfg file was created

Ill backup USB anyway, and if all else fails, will recreate usb drive and restore config

Cheers 

Edited by bdydrp

Share this post


Link to post

Have run the usb creator tool, and copied my existing config folder.

 

Now it doesnt want to boot at all, it just goes straight to bios 

 

Will have another look tomorrow afternoon  

Share this post


Link to post
5 minutes ago, johnnie.black said:

Make sure you enabled UEFI boot when creating the flash, or just rename "EFI-" to "EFI"

Ahhhhhhhh

I remeber renaming that folder previously (on another thread i read)

 

Ill look at tomorrow 

Share this post


Link to post

Quick test before work, 

It now boots fine after renaming folder.

 

But now at login screen, IPv4 is not set.

Something is causing it to not get an IP from my DHCP.

 

Possibly an issue with my onboard NIC??

Share this post


Link to post
1 minute ago, bdydrp said:

Possibly an issue with my onboard NIC??

Possibly, is network.cfg being created? If not see if you can get the diags from the console by typing "diagnostics"

Share this post


Link to post
3 hours ago, johnnie.black said:

Possibly, is network.cfg being created? If not see if you can get the diags from the console by typing "diagnostics"

Yes, network.cfg is created and I can see its set to dhcp. 

I'll get the diagnostics and post them when I'm home. 

 

Share this post


Link to post
1 hour ago, johnnie.black said:

NIC isn't loading a driver, try the latest beta.

I'll give that a go. 

Cheers 

Share this post


Link to post

Latest beta worked.

Driver loaded and IP received from DHCP

 

Main page loaded but some disk were not assigned..

So will double check sata cables.

 

Would it be safe to assume other disks remained on correct slot?

Share this post


Link to post

All good now

Thanks for your help

 

Beta version solved the issues

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this