grrant Posted July 16, 2020 Posted July 16, 2020 Long story short, just updated my FreeNAS rig to unRaid. Purchased several 8TB drives, new and one is reporting errors already. Been up for a few days. Its my parity drive. Any help would be appreciated. smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.19.107-Unraid] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda Compute Device Model: ST8000DM004-2CX188 Serial Number: ZCT2DXLW LU WWN Device Id: 5 000c50 0c59b0c10 Firmware Version: 0001 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5425 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 15 19:47:40 2020 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 945) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 074 064 006 - 22442647 3 Spin_Up_Time PO---- 093 091 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 59 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 074 060 045 - 24086294 9 Power_On_Hours -O--CK 100 100 000 - 285 (62 193 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 59 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 097 097 099 NOW 3 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 095 000 - 8590262277 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 071 055 040 - 29 (Min/Max 25/33) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 53 193 Load_Cycle_Count -O--CK 100 100 000 - 65 194 Temperature_Celsius -O---K 029 045 000 - 29 (0 24 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 074 064 000 - 22442647 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 133 (222 214 0) 241 Total_LBAs_Written ------ 100 253 000 - 48382710241 242 Total_LBAs_Read ------ 100 253 000 - 30720092629 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 24 Device vendor specific log 0xa2 GPL VS 8160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 9048 Device vendor specific log 0xbd GPL VS 8 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 16 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 24 Device vendor specific log 0xd1 GPL VS 264 Device vendor specific log 0xd3 GPL VS 1920 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 260 hours (10 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 00 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 05 40 00 00 c4 4d 2e c0 e0 00 1d+02:47:39.150 READ DMA EXT 25 00 00 05 40 00 00 c4 4d 44 40 e0 00 1d+02:47:39.147 READ DMA EXT 25 00 00 05 40 00 00 c4 4d 3f 00 e0 00 1d+02:47:39.143 READ DMA EXT 25 00 00 05 40 00 00 c4 4d 39 c0 e0 00 1d+02:47:39.139 READ DMA EXT 25 00 00 05 40 00 00 c4 4d 34 80 e0 00 1d+02:47:39.136 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 260 hours (10 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 00 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 00 80 00 6b 40 40 00 1d+02:47:09.763 READ FPDMA QUEUED 60 00 00 00 80 00 00 80 1f 48 00 40 00 1d+02:47:09.763 READ FPDMA QUEUED 60 00 00 00 08 00 00 80 00 01 78 40 00 1d+02:47:09.763 READ FPDMA QUEUED 60 00 00 00 80 00 00 c4 4d 34 00 40 00 1d+02:47:09.762 READ FPDMA QUEUED 60 00 00 05 40 00 00 c4 4d 34 80 40 00 1d+02:47:09.762 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 260 hours (10 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 00 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 05 40 00 00 c4 4d 44 40 40 00 1d+02:46:40.279 READ FPDMA QUEUED 60 00 00 05 40 00 00 c4 4d 3f 00 40 00 1d+02:46:40.279 READ FPDMA QUEUED 60 00 00 05 40 00 00 c4 4d 39 c0 40 00 1d+02:46:40.279 READ FPDMA QUEUED 60 00 00 05 40 00 00 c4 4d 34 80 40 00 1d+02:46:40.279 READ FPDMA QUEUED 60 00 00 00 80 00 00 c4 4d 34 00 40 00 1d+02:46:40.278 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 25/33 Celsius Lifetime Min/Max Temperature: 24/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 3 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (30) Index Estimated Time Temperature Celsius 31 2020-07-10 14:20 ? - 32 2020-07-10 15:19 29 ********** 33 2020-07-10 16:18 ? - 34 2020-07-10 17:17 29 ********** 35 2020-07-10 18:16 ? - 36 2020-07-10 19:15 28 ********* 37 2020-07-10 20:14 ? - 38 2020-07-10 21:13 28 ********* 39 2020-07-10 22:12 ? - 40 2020-07-10 23:11 24 ***** 41 2020-07-11 00:10 30 *********** 42 2020-07-11 01:09 29 ********** 43 2020-07-11 02:08 30 *********** 44 2020-07-11 03:07 30 *********** 45 2020-07-11 04:06 30 *********** 46 2020-07-11 05:05 29 ********** ... ..( 3 skipped). .. ********** 50 2020-07-11 09:01 29 ********** 51 2020-07-11 10:00 28 ********* 52 2020-07-11 10:59 29 ********** ... ..( 2 skipped). .. ********** 55 2020-07-11 13:56 29 ********** 56 2020-07-11 14:55 27 ******** 57 2020-07-11 15:54 29 ********** 58 2020-07-11 16:53 29 ********** 59 2020-07-11 17:52 29 ********** 60 2020-07-11 18:51 28 ********* 61 2020-07-11 19:50 28 ********* 62 2020-07-11 20:49 29 ********** 63 2020-07-11 21:48 29 ********** 64 2020-07-11 22:47 28 ********* 65 2020-07-11 23:46 28 ********* 66 2020-07-12 00:45 29 ********** 67 2020-07-12 01:44 27 ******** 68 2020-07-12 02:43 29 ********** ... ..( 7 skipped). .. ********** 76 2020-07-12 10:35 29 ********** 77 2020-07-12 11:34 27 ******** 78 2020-07-12 12:33 29 ********** 79 2020-07-12 13:32 27 ******** 80 2020-07-12 14:31 29 ********** 81 2020-07-12 15:30 27 ******** 82 2020-07-12 16:29 30 *********** 83 2020-07-12 17:28 30 *********** 84 2020-07-12 18:27 30 *********** 85 2020-07-12 19:26 31 ************ 86 2020-07-12 20:25 30 *********** ... ..( 2 skipped). .. *********** 89 2020-07-12 23:22 30 *********** 90 2020-07-13 00:21 29 ********** 91 2020-07-13 01:20 30 *********** 92 2020-07-13 02:19 30 *********** 93 2020-07-13 03:18 30 *********** 94 2020-07-13 04:17 29 ********** ... ..( 3 skipped). .. ********** 98 2020-07-13 08:13 29 ********** 99 2020-07-13 09:12 28 ********* 100 2020-07-13 10:11 28 ********* 101 2020-07-13 11:10 28 ********* 102 2020-07-13 12:09 29 ********** 103 2020-07-13 13:08 29 ********** 104 2020-07-13 14:07 28 ********* 105 2020-07-13 15:06 ? - 106 2020-07-13 16:05 25 ****** 107 2020-07-13 17:04 31 ************ 108 2020-07-13 18:03 30 *********** 109 2020-07-13 19:02 30 *********** 110 2020-07-13 20:01 31 ************ 111 2020-07-13 21:00 31 ************ 112 2020-07-13 21:59 29 ********** 113 2020-07-13 22:58 30 *********** ... ..( 2 skipped). .. *********** 116 2020-07-14 01:55 30 *********** 117 2020-07-14 02:54 29 ********** 118 2020-07-14 03:53 30 *********** 119 2020-07-14 04:52 29 ********** ... ..( 5 skipped). .. ********** 125 2020-07-14 10:46 29 ********** 126 2020-07-14 11:45 30 *********** 127 2020-07-14 12:44 30 *********** 0 2020-07-14 13:43 30 *********** 1 2020-07-14 14:42 32 ************* 2 2020-07-14 15:41 31 ************ 3 2020-07-14 16:40 31 ************ 4 2020-07-14 17:39 31 ************ 5 2020-07-14 18:38 32 ************* 6 2020-07-14 19:37 32 ************* 7 2020-07-14 20:36 30 *********** 8 2020-07-14 21:35 31 ************ 9 2020-07-14 22:34 32 ************* 10 2020-07-14 23:33 31 ************ 11 2020-07-15 00:32 30 *********** 12 2020-07-15 01:31 31 ************ 13 2020-07-15 02:30 32 ************* 14 2020-07-15 03:29 30 *********** 15 2020-07-15 04:28 31 ************ ... ..( 6 skipped). .. ************ 22 2020-07-15 11:21 31 ************ 23 2020-07-15 12:20 32 ************* 24 2020-07-15 13:19 31 ************ 25 2020-07-15 14:18 32 ************* 26 2020-07-15 15:17 32 ************* 27 2020-07-15 16:16 32 ************* 28 2020-07-15 17:15 31 ************ 29 2020-07-15 18:14 30 *********** 30 2020-07-15 19:13 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 59 --- Lifetime Power-On Resets 0x01 0x010 4 285 --- Power-on Hours 0x01 0x018 6 47787928897 --- Logical Sectors Written 0x01 0x020 6 49813650 --- Number of Write Commands 0x01 0x028 6 30719974162 --- Logical Sectors Read 0x01 0x030 6 29616280 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 168 --- Spindle Motor Power-on Hours 0x03 0x010 4 168 --- Head Flying Hours 0x03 0x018 4 65 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 53 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 5 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 31 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 45 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 28 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 46 --- Number of Hardware Resets 0x06 0x010 4 21 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS Quote
JorgeB Posted July 16, 2020 Posted July 16, 2020 Please post the diagnostics: Tools -> Diagnostics, you can also run an extended SMART test on that disk. Quote
grrant Posted July 17, 2020 Author Posted July 17, 2020 As requested, thank you!!! unraid-6.8.3.txt domain.cfg flash.cfg go docker.cfg super.dat ident.cfg share.cfg network.cfg disk.cfg docker.txt syslog.txt no qemu log files appdata.cfg system.cfg G------------n.cfg WDC_WD80EMAZ-00WJTA0_2SGGBEHW-20200715-1947 disk5 (sdg).txt WDC_WD80EMAZ-00WJTA0_2SGH4RSJ-20200715-1947 disk2 (sdc).txt WDC_WD60EFRX-68L0BN1_WD-WX11D66CVT16-20200715-1947 disk6 (sdi).txt WDC_WD6002FFWX-68TZ4N0_K1HBND1B-20200715-1947 disk8 (sdk).txt WDC_WD60EFRX-68L0BN1_WD-WXB1HB4RJRCA-20200715-1947 disk9 (sdh).txt WDC_WD80EMAZ-00WJTA0_1EH96UPZ-20200715-1947 disk4 (sde).txt WDC_WDS250G1B0A-00H9H0_170433803243-20200715-1947 cache (sdj).txt SanDisk_Ultra_Fit_4C530001141231118513-0-0-20200715-1947 flash (sda).txt ST8000DM004-2CX188_ZCT2DXLW-20200715-1947 parity (sdl).txt WDC_WD80EMAZ-00WJTA0_1EHPNLSZ-20200715-1947 disk3 (sdd).txt WDC_WD80EMAZ-00WJTA0_1EHPGLDN-20200715-1947 disk1 (sdb).txt WDC_WD6002FFWX-68TZ4N0_K1GX6N0D-20200715-1947 disk7 (sdf).txt cmdline.txt plugins.txt motherboard.txt iommu_groups.txt ethtool.txt folders.txt lsmod.txt lsscsi.txt loads.txt memory.txt lspci.txt meminfo.txt lsusb.txt top.txt ps.txt vars.txt lscpu.txt lsof.txt df.txt ifconfig.txt Quote
JorgeB Posted July 18, 2020 Posted July 18, 2020 Next time please upload the single diagnostics.zip, much easier for us to check. Missed in the earlier post before (mostly because it's not so easy to read when not posted inside code tags) that parity as a FAILING NOW SMART attribute: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 184 End-to-End_Error -O--CK 097 097 099 NOW 3 So it needs to be replaced. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.