NREES87 Posted August 28, 2020 Share Posted August 28, 2020 I'm currently trying to deal with the fact my server died mid-rebuild and completely borked Disk1 (now showing "Unmountable File System Present") and the Web UI is currently driving me to frustration. 80% of the time, I'm getting "Hmmm… can't reach this page. It looks like 192.168.XX.XX closed the connection" and then 20% of the time it works fine for a few minutes before crashing and burning again. I've tried 3 different laptops, a tablet, 2 phones and a PC and the behaviour is consistent. Also, my 2nd UnRaid server is behaving exactly as expected. I've attached the diagnostics, in case anyone has any suggestions?! tower-diagnostics-20200828-0806.zip Quote Link to comment
HK-Steve Posted August 30, 2020 Share Posted August 30, 2020 I have exactly the same problem today, Had a problem with my Modem, had to do a factory reset, Now every 2 mins or so, can not access. My other 2x Towers are fine, just my Tower3 which is all my movies. Diags attached tower3-diagnostics-20200830-1518.zip Quote Link to comment
Squid Posted August 30, 2020 Share Posted August 30, 2020 Did you reset the modem while the server was still on? (at 15:13?) The network went down at that time. If this wasn't when you reset modem, then I'd try a different port on the switch / modem Quote Link to comment
HK-Steve Posted August 30, 2020 Share Posted August 30, 2020 No, I reset the modem yesterday, today just can not stay connected. Changed cables and network switch also. Moved Tower to another room and same problem. Thanks for looking and suggestions This Tower3 has been online for a very long time with no issues, strange my other 2x Towers were not effected, running the same UnRaid version Quote Link to comment
HK-Steve Posted August 30, 2020 Share Posted August 30, 2020 Changed port on my Modem, still the same. 😡 Replaced my 16 port switch with a new unit, still the same. Hmmmmmmm Think I will shutdown all my network switches (I have about 10x switches) and repower them and see what happens Quote Link to comment
HK-Steve Posted August 30, 2020 Share Posted August 30, 2020 I reset my whole network, still the same Quote Link to comment
HK-Steve Posted August 30, 2020 Share Posted August 30, 2020 After messing around for the last couple of hrs, I changed my IP address to automatic, then back to a static IP address after a reboot, and now all is good. Weird, never had that happen before. Quote Link to comment
drowsyfish Posted September 1, 2020 Share Posted September 1, 2020 How do we do this via the CLI? I can access my UI every 15th time and even then it fails the next page I load or settings that is changed. Also I tried a putty connection and it connected prefect but failed 10 seconds later. I am running 6.8.3 and when I get home was planning on trying older version / different usb. No idea what the issue is. Quote Link to comment
trurl Posted September 1, 2020 Share Posted September 1, 2020 5 minutes ago, drowsyfish said: How do we do this via the CLI? I can access my UI every 15th time and even then it fails the next page I load or settings that is changed. Also I tried a putty connection and it connected prefect but failed 10 seconds later. I am running 6.8.3 and when I get home was planning on trying older version / different usb. No idea what the issue is. Possibly issue with flash disconnecting. Be sure to boot from a USB2 port. Go to Tools - Diagnostics and attach the complete Diagnostics ZIP file to your NEXT post. Quote Link to comment
drowsyfish Posted October 1, 2020 Share Posted October 1, 2020 On 9/1/2020 at 8:23 AM, trurl said: Possibly issue with flash disconnecting. Be sure to boot from a USB2 port. Go to Tools - Diagnostics and attach the complete Diagnostics ZIP file to your NEXT post. I was using a 2.0 port but I had remembered my boss saying he has had alot of issues with certain 3.0 flash drives for booting. Swapped for another and all was well. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.