Skip to content
View in the app

A better way to browse. Learn more.

Unraid

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

crash-Webui partly showing, samba/nfs not avilable..

Featured Replies

So the last couple of days (maybe one week) my unraid server "crashes" during the night/morning.. no network shares are available either. After a reboot, everything seemingly works as its supposed to. I cant figure out what causes it. I have tried to describe what happens below:
the webui only displays the "Header" with main menu buttons, but not any actual content in the main part ( if that makes sense)
I can access the terminal from the webui (only terminal and logout buttons are available on the right edge of the header)
I can run diagnostics, and it reports that the fille was created in /boot/....... but when i check the usb, the new file is not there...
I can only get the diagnostics file from when the server is rebooted in a seemingly healthy state.
The attached diagnostic is after a reboot, hope it may provide some insight...
Chkdsk of the usb-drive on a windows reports no errors...


Any, help would be greatly appreciated tower-diagnostics-20201022-1700.zip:)
 

  • Community Expert

That sounds like a flash drive dropping issue, since you're using a USB 3.0 port and those are not recommended try a 2.0 one, you can also do this, and if it happens again post that log.

  • Author
27 minutes ago, JorgeB said:

That sounds like a flash drive dropping issue, since you're using a USB 3.0 port and those are not recommended try a 2.0 one, you can also do this, and if it happens again post that log.

I'm using the motherboard of an old optiplex 7010, there is no USB3.0 ports on that thing..
I will try the syslog server!

  • Community Expert
1 minute ago, shanix said:

there is no USB3.0

Yes, you're right of course, my bad, only looked at the driver and that driver can be used for USB 3.0 but also 2.0 on older boards, you can still try the other USB controller controller, it uses a different driver, though any Intel USB 2.0 port usually works OK.

  • Author
2 hours ago, JorgeB said:

you can also do this, and if it happens again post that log.

So it happened again, syslog attached.

could this be a hardware or flash drive issue then?
 

syslog.log

  • Community Expert

IRQ16 got disable, and it appears to be the one used by the controller where the flash drive is, you could try the other USB controller.

 

 

  • Author

Just wanted to report back and say there have been no issues after moving the flash drive from the back motherboard ports to the front panel usb port.
Thanks a lot for the speedy help!!!
Any idea if the IRQ16 issue could be controller/hub or single port issue?

 

  • Community Expert
55 minutes ago, shanix said:

Any idea if the IRQ16 issue could be controller/hub or single port issue?

Difficult to say, BIOS update might help, same for a newer kernel in a future Unraid release.

Archived

This topic is now archived and is closed to further replies.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.