[[Support] binhex - Plex]

Added a NVIDIA card this weekend.  Followed instruction in Q3 of the support documentation but I do not have the fields NVIDIA_DRIVER_CAPABILITIES and NVIDIA_VISIBLE_DEVICES.  I added the variables manually and set appropriately but Transcoding is not using HW.  Using Unraid 9.2 and have Plex Transcode settings ticked off.  Any advice would be appreciated.  Thank you

[[Support] Linuxserver.io - Unifi-Controller]

I had an issue w/ the constant adopting/disconnect loop.  Maybe the following will help someone else.

 

I have the unraid box set with a DNS resolvable name in pfsense.  In my case just "tower".  So using ssh from the unifi device I can ping w/ simply "ping tower".  The controller hostname/ip set to the ip used to access unraid.  I know have selected "Override inform host with controller hostname/IP" as suggested by others and should hopefully keep the issue from reoccurring. 

 

Since I am using Windows I used putty to ssh into the device using the ip address assigned by the router (pfsense) and port 22.  The mistake I used here was trying to use the controller ID/PWD instead of what was in the Site/Device Authentication field of the controller.  Of course w/ SSH checked there.  With those credentials login to the device.  Then run the "set-inform http://unraidip:port/inform"

 

replace unraid ip w/ the address for your unraid box such as 192.168.x.x

 

replace port with the port number defined in your unraid unifi controller container as "Port used for HTTP portal redirection.:"

 

the port thing was the next stumbling block for me as I was attempting to use the port of the controller.  I'm not the best w/ these things so hopefully this is clear enough for anyone w/ a similar issue.  Sorry if it is a repost.  Thank  you to everyone providing their assistance.

[[Support] binhex - SABnzbdVPN]

I'm attempting to utilize the new wireguard setup after a successful openvpn setup.  I use Torguard for my VPN service.  I have wireguard selected and I utilized the tool here https://torguard.net/tgconf.php?action=vpn-openvpnconfig for creating a wireguard config from Torguard.  I entered in my details as requested to generate the config.  I then started and stopped wireguard service and replaced the information in the wg0.conf file w/ my config information.  I verified that the information stays after booting up the container.  I also updated "Extra Parameters" to be "--privileged=true".  The container starts buts that is all I get.  I attached a screenshot of my settings w/ user and pwd temporarily removed.  I would appreciate any assistance.  Thank you in advance.

[Preclear plugin]

4 hours ago, trurl said:

 

You seem to have left out some important details in your description. You can't get directly from adding a disk to "unmountable no file system". If you add a disk to a new slot and that disk hasn't been marked as cleared then unRAID is going to clear it for you and then offer to format it. Even if it was mistakenly marked as clear by the failed preclear unRAID would still offer to format it. Maybe if you had taken a closer look you would have noticed that it was telling you to check a box to format the disk when the array was started. Or did you do a New Config to add the disk to the array?

 

Definitely NOT fine to leave as is. In order to remove the disk from the array you will have to New Config without it and resync parity.

 

*EDIT*

Another possibility would be to assign it back to the slot it is missing from and then check the box to format it. Any time you check the box to format make very sure that only the disk you want to format is unmountable. You should definitely do a parity check afterwards since it isn't completely clear what you did to get to this state.

I apologize for the lack of clarity.  I did not see the format option at the time, had my browser a little scrunched.  The option was down at the bottom.  I stopped the array and replaced the drive into the slot I was attempting before.  Once that was done I selected the format option.  After completing the format its added the drive but the orange triangle lists it as "contents emulated".  The parity sync is running now.

 

Thanks again for replying.

[Preclear plugin]

I attempted running the two most recent ver of the plugin on two new drives and both failed step 5.  Swapped cables with working drives and still failed the same.  I attempted just to add one of the drives to the array due to the above noted issues w/ the plugin for my ver of unraid 6.4.x. I get a "unmountable no file system" error for the disk I had attempted preclear on.  So I removed the drive from the array and put it into unassigned disks.   Should I wait it out for the plugin update or is there a better course of action?  The array says it is missing that disk now but I never wrote to it or ran a parity check with it so it seems like it would be fine to leave as is.

 

Thanks

 

Justin