tstorzuk
-
Posts
23 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by tstorzuk
-
-
If you've been following my posts, I'm new to unRAID. I don't have it installed yet even, but I am going through the process of preclearing all of my drives on my newest server.
I have 24 HDD's that I'm going through the preclear process and am on my 3rd batch of 6. I can only run 6 drives at a time as my multiple controller cards are not recognized by version 4.7. And I'm not interested in testing out the development series yet. I will wait until I have run through all my preclear checks.
I am running each drive 6 times through preclear, as I do not want to worry much about having a failure. It takes a lot of time to recover from one, and I currently have one of my servers sitting around waiting until I have time to correct/replace one of it's faulty drives. It takes a lot to get into my servers as they are all crammed into a storage closet, at the very back. I have to move full shelving units and my deep freezer out of the way to wheel out the server rack.....then disconnect LOADS of cables. The last time I took it out of the storage room, I took some photos. Attached is one to show you what I'm talking about.
I'm not sure what to look for in the results, so I'm posting one of them here. I tried to post 6 in this thread (1 batch), but it exceeded the maximum allowed characters by more than 4 times!!! So if someone could point out which areas to look at, and what types of numbers to watch out for it would be greatly appreciated.
1st disk to finish
========================================================================1.13 == invoked as: ./preclear_disk.sh -r 65536 -w 65536 -b 2000 -A -c 6 -m [email protected] /dev/sdc == ST3000DM001-1CH166 W1F1GJDG == Disk /dev/sdc has been successfully precleared == with a starting sector of 1 == Ran 6 cycles == == Using :Read block size = 65536 Bytes == Last Cycle's Pre Read Time : 6:35:04 (126 MB/s) == Last Cycle's Zeroing time : 5:33:50 (149 MB/s) == Last Cycle's Post Read Time : 11:55:20 (69 MB/s) == Last Cycle's Total Time : 17:30:15 == == Total Elapsed Time 112:42:31 == == Disk Start Temperature: 29C == == Current Disk Temperature: 31C, == ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdc /tmp/smart_finish_sdc ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 117 100 6 ok 131179216 Seek_Error_Rate = 63 100 30 ok 2312779 Spin_Retry_Count = 100 100 97 near_thresh 0 End-to-End_Error = 100 100 99 near_thresh 0 High_Fly_Writes = 94 100 0 ok 6 Airflow_Temperature_Cel = 69 71 45 near_thresh 31 Temperature_Celsius = 31 29 0 ok 31 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 6. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 6. 0 sectors were pending re-allocation after post-read in cycle 1 of 6. 0 sectors were pending re-allocation after zero of disk in cycle 2 of 6. 0 sectors were pending re-allocation after post-read in cycle 2 of 6. 0 sectors were pending re-allocation after zero of disk in cycle 3 of 6. 0 sectors were pending re-allocation after post-read in cycle 3 of 6. 0 sectors were pending re-allocation after zero of disk in cycle 4 of 6. 0 sectors were pending re-allocation after post-read in cycle 4 of 6. 0 sectors were pending re-allocation after zero of disk in cycle 5 of 6. 0 sectors were pending re-allocation after post-read in cycle 5 of 6. 0 sectors were pending re-allocation after zero of disk in cycle 6 of 6. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. ============================================================================ ============================================================================ == == S.M.A.R.T Initial Report for /dev/sdc == Disk: /dev/sdc smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST3000DM001-1CH166 Serial Number: W1F1GJDG Firmware Version: CC24 User Capacity: 3,000,592,982,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Thu Jun 6 22:32:51 2013 MDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 89) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 006 Pre-fail Always - 949336 3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 42 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 908 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 5 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 42 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 071 069 045 Old_age Always - 29 (Lifetime Min/Max 26/29) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 40 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 87 194 Temperature_Celsius 0x0022 029 040 000 Old_age Always - 29 (0 23 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 39058432589824 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 66 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 14474 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. == ============================================================================ ============================================================================ == == S.M.A.R.T Final Report for /dev/sdc == Disk: /dev/sdc smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST3000DM001-1CH166 Serial Number: W1F1GJDG Firmware Version: CC24 User Capacity: 3,000,592,982,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Tue Jun 11 15:15:21 2013 MDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 89) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 131179216 3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 42 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 063 060 030 Pre-fail Always - 2312779 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 118 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 42 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 094 094 000 Old_age Always - 6 190 Airflow_Temperature_Cel 0x0022 069 068 045 Old_age Always - 31 (Lifetime Min/Max 26/32) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 40 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 87 194 Temperature_Celsius 0x0022 031 040 000 Old_age Always - 31 (0 23 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 64029372448881 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 35163223210 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 76403288396 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. == ============================================================================
Preclear.sh results - Questions about your results? Post them here.
in User Customizations
Posted
Thanks for the information. Ok, I think the drives I have run are good so far. The 3rd batch of 6 drives has finished since my last post. When I get home tonight, I'll be running my 4th and final batch of drives on this server through preclear.
Preclear actually does recognize my 3TB HDD's (as you can see from the detailed report I attached in my previous post). It's just unRAID that doesn't.
I'm hoping that the stable 5.0 release will be ready by the time I run my final set of HDD's through preclear. And when it is ready, I'll find out if it can recognize my multiple controller cards.