RussellG
-
Posts
20 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by RussellG
-
-
On 9/10/2022 at 12:14 PM, trurl said:
Rebuilt disk2 is mounted and 70% full so should be OK.
Your docker/VM setup is less than ideal but we can discuss after you get your array stable.
Looks like that'll be a bit. Disk1 is not giving me errors, but Disk2 is now having read errors. I just got a new 10tb in yesterday, so I am going to get that in and replace Disk2 since it's having active read errors now. These HGSTs have been sitting around for a bit and weren't tested, so I guess that's a failure on my part since they are obviously both bad.
-
Alright, so it finished. There were 35 errors and it appears disk1 is also bad. Given it had water damage (replaced PCB) and all that stress, I'm not surprised. I've got a couple more drives on order to get everything up and safe. Disk2 didn't show any errors on rebuild, so it should be good, for now. It appears I am mostly in the clear though.
-
11 minutes ago, JorgeB said:
Yep.
Oh yeah, much better now
-
1
-
-
4 minutes ago, JorgeB said:
Problem is disk2, it's failing:
=== START OF READ SMART DATA SECTION === SMART Health Status: FAILURE PREDICTION THRESHOLD EXCEEDED: ascq=0xfd [asc=5d, ascq=fd]Do you have another spare?
I do. So just stop the re-build, replace with the other drive, and rebuild again?
-
33 minutes ago, trurl said:
Post new diagnostics
Got it to speed up a good bit by disabling docker. Probably some of my containers trying to do things.
Diags attached -
1 hour ago, trurl said:
Thanks for the donation!
Let us know how it goes.
Going Slowly 🥲
-
3 hours ago, trurl said:
That shows emulated disk2 is mounted and 70% full. So all you have to do is rebuild!
You are at that step now.
Fingers crossed. Started rebuild with new disk. Thank you for your help! Sent over some beer/pizza funds as thanks.
-
32 minutes ago, trurl said:
If emulated disk2 shows as unmountable, DO NOT FORMAT.
I will check back tomorrow
Ok, so it started. And everything looks ok at first glance and a few spot checks? Requested diags and SS attached.32 minutes ago, trurl said:If emulated disk2 shows as unmountable, DO NOT FORMAT.
I will check back tomorrow
Roger. I am going to stop it for the night.
-
2 hours ago, trurl said:
OK
Stop the array, set disk2 to Not Assigned
Start the array in Normal mode (don't check Maintenance mode)
Post a screenshot and new diagnostics
Ok, to confirm, do not check maintenance mode. It also wants me check this to start it:
-
4 hours ago, trurl said:
Follow these instruction carefully. We will check along the way to make sure things are as they should be. If things don't seem to be working as described, or you have questions, ask.
- Install new disk2
- Go to Tools - New Config, Retain All, Apply
- Assign new disk2
- Check BOTH Maintenance mode AND Parity Valid boxes
- Start the array
Then post a screenshot
Alright, Done with all those steps.
Screenshot:
-
2 minutes ago, trurl said:
Follow these instruction carefully. We will check along the way to make sure things are as they should be. If things don't seem to be working as described, or you have questions, ask.
- Install new disk2
- Go to Tools - New Config, Retain All, Apply
- Assign new disk2
- Check BOTH Maintenance mode AND Parity Valid boxes
- Start the array
Then post a screenshot
Ok, i am out for about 3-4 hours and will begin that when i get back.
In the event Disk1 is bad, this would not do anything to the parity disk, correct? I ask because the old Disk2 may be repairable I am still looking at purchasing another WD100EZAZ drive and taking that PCB, swapping ROM IC and fixing it.
i guess i could just mount disk1 and look at its contents to somewhat verify it’s ok? -
10 hours ago, trurl said:
Attach diagnostics to your NEXT post in this thread.
unraid-diagnostics-20220908-0855.zip
Attached, apologies I dropped out yesterday. It was late over here.
-
19 minutes ago, trurl said:
Do you have a new 10TB disk ready to assign as disk2?
I do.19 minutes ago, trurl said:Don't do anything without further advice
10-4 -
Ok, so I had a crazy AC leak and two of my three drives got wet and the PCBs fried. I had one parity, but two drives failed. I have since repaired one of the two bad drives (swapped ROM IC to a new donor board) and want to rebuild parity, but unraid has forgotten one of the disks. Before I go any further and bring confusion, I am going to start with my disks and their status
10Tb Parity - Good and healthy
10Tb Disk1 - Repaired and appears to be fine, but unRAID doesn't "remember" it?10Tb Disk2 - Bad and missing.
So as you can see. Parity shows good. Disk1 (MPN) which is the original disk, has been forgotten for some reason. Disk2 (2MZ) is bad and I plan to replace with a good 10Tb drive. What I need to do is get unRAID to "remember" Disk1 and rebuild to a new disk for disk2. How do i do this?
I do not have any config backups. Any backups I had were on the array (lesson learned there). What can i do? Help me Tom Cruise, please and thank you! -
I created VM, performed all steps, and it boots up perfect; however, when I pass through a controller (Sonnet Allegro USB3-PRO-4P10-E), it takes about 5 minutes for the VM to even start, and the controller does show up in the OS X System Report. No USB devices show available that are plugged into the controller. Anything that I can check or do? I followed the SI1 video on controller passthrough and have another VM with a different controller (also Sonnet Allegro) passed through just fine. At one point I did see the controller on a different Mac VM, but I deleted that VM to create a new one and even following the same steps, cannot get it to show up now.
-
Well I had this working for a week, then i added an account for my wife and it broke any connection from iOS apps. I am not getting timeout errors constantly from any iOS device with any nextcloud account i have set up. I am thinking it might be a file permissions issue with uploading photos to the /Photos folder, but I do not know how to get to the folder and check permissions?
-
I am unable to get my mouse to move? I removed the tablet line and still unable to get it to move?
Strap In for this... Parity Good. One Good Drive Forgotten, Bad Drive Missing
in General Support
Posted · Edited by RussellG
Alright, so I was seeing this:
Per unraid instructions, went to do an XFS repair on md2 (because that's where logs were showing issues) and seeing this:
So I guess I will just replace disk2 when i get home and rebuild to that.