Harlan Posted November 18, 2022 Share Posted November 18, 2022 本来是网线直连我PC上的另一张浪潮万兆网卡的 , 记得之前测试的时候虽然没有万兆但是可以跑到200m/s+ 某次版本升级后就只能以100Mbps和windows协议了 , 插拔过 , 也连过千兆交换机 , 都是100Mbps 附上我的设置 Quote Link to comment
Harlan Posted November 18, 2022 Author Share Posted November 18, 2022 ethtool -i eth3 driver: ixgbe version: 5.19.17-Unraid firmware-version: 0x8000052f expansion-rom-version: bus-info: 0000:04:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes Quote Link to comment
zhiwen Posted November 18, 2022 Share Posted November 18, 2022 (edited) 这种情况应该是网卡自动协商的速率不对,建议尝试使用命令设置网口速率到万兆,有效果的话把命令写到 /boot/config/go 里开机时执行 /usr/sbin/ethtool -s eth3 speed 10000 duplex full autoneg on && /sbin/ifconfig eth3 down && /sbin/ifconfig eth3 up Edited November 18, 2022 by zhiwen 2 Quote Link to comment
Harlan Posted November 18, 2022 Author Share Posted November 18, 2022 5 minutes ago, zhiwen said: 这种情况应该是网卡自动协商的速率不对,建议尝试使用命令设置网口速率到万兆,有效果的话把命令写到 /boot/config/go 里开机时执行 /usr/sbin/ethtool -s eth2 speed 2500 duplex full autoneg on && /sbin/ifconfig eth2 down && /sbin/ifconfig eth2 up 感谢 , 但是尝试改为我的网卡 eth3\4后还是无法协商到万兆 Quote Link to comment
zhiwen Posted November 18, 2022 Share Posted November 18, 2022 试试 autoneg off,看看 ethtool eth3 Quote Link to comment
Harlan Posted November 18, 2022 Author Share Posted November 18, 2022 33 minutes ago, zhiwen said: 试试 autoneg off,看看 ethtool eth3 Settings for eth3: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: on Port: Twisted Pair PHYAD: 0 Transceiver: internal MDI-X: Unknown Supports Wake-on: umbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes Quote Link to comment
Solution zhiwen Posted November 18, 2022 Solution Share Posted November 18, 2022 看起来自动协商没问题,尝试换网线和换pcie插槽 Quote Link to comment
Harlan Posted November 18, 2022 Author Share Posted November 18, 2022 1 minute ago, zhiwen said: 看起来自动协商没问题,尝试换网线和换pcie插槽 好的 感谢回复 我试试切换Pcie Quote Link to comment
Harlan Posted November 18, 2022 Author Share Posted November 18, 2022 17 minutes ago, zhiwen said: 看起来自动协商没问题,尝试换网线和换pcie插槽 还真是pcie问题 去掉一个设备之后就可以万兆了 可能是通道不够了 Quote Link to comment
Harlan Posted November 18, 2022 Author Share Posted November 18, 2022 18 minutes ago, zhiwen said: 看起来自动协商没问题,尝试换网线和换pcie插槽 感谢大佬 Quote Link to comment
swolfe Posted January 8 Share Posted January 8 请问你的X540-T2网卡是怎么认出来的啊?我的unraid认不出来,是不是因为我的unraid版本太低?我的是6.11.5 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.